Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER(w/ Pintle Hook) › from 2015.08
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255832 REAR BUMPER(w/ Pintle Hook) A

EXTERIOR PANELS / TRIM  REAR BUMPER(w/ Pintle Hook)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 57616B 1.INSTALL REAR BUMPER ARM BRACKET LH

a.

Install the rear bumper arm bracket LH with the 2 bolts.


b.

Attach the clamp.


Hide 57615C 2.INSTALL REAR BUMPER ARM BRACKET

a.

Install the rear bumper arm bracket with the bolt.

HINT:

Use the same procedure for both bumper arm brackets.



Hide 52172B 3.INSTALL REAR BUMPER NO. 2 REINFORCEMENT

a.

Install the rear bumper No. 2 reinforcement with the 2 bolts.


Hide 52156A 4.INSTALL REAR BUMPER SIDE SUPPORT LH

a.

Attach the 6 claws to install the rear bumper side support LH.


b.

Install the 3 screws.


Hide 52155A 5.INSTALL REAR BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure described for the LH side.


Hide 52563D 6.INSTALL REAR BUMPER UPPER RETAINER LH

a.

Attach the 2 clips to install the rear bumper upper retainer LH.


Hide 52562E 7.INSTALL REAR BUMPER UPPER RETAINER RH

HINT:

Use the same procedure described for the LH side.


Hide 81560 8.INSTALL REAR COMBINATION LIGHT ASSEMBLY LH

Hide 81550 9.INSTALL REAR COMBINATION LIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 58724B 10.INSTALL NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

a.

Install the No. 2 luggage compartment side cover protector with 2 new grommets.


b.

Install the 2 screws.


Hide 58723B 11.INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

HINT:

Use the same procedure described for the LH side.


Hide 52159 12.INSTALL REAR BUMPER COVER

HINT:

For the rear bumper cover with tire carrier, use the procedures described below.


a.

w/ TOYOTA Parking Assist-sensor System or w/ Rear Fog Light:

Connect the No. 2 frame wire connector.


b.

Attach the 14 claws to install the rear bumper cover.


c.

Install the 7 bolts, 6 screws and 2 clips.


d.

Open the tail gate and install the 4 clips.


e.

Close the tail gate.


Hide 52162B 13.INSTALL REAR BUMPER NO. 1 PLATE (for Step)

a.

Attach the 20 claws to install the rear bumper No. 1 plate.


Hide 76626E 14.INSTALL REAR QUARTER PANEL MUDGUARD LH

Hide 76625G 15.INSTALL REAR QUARTER PANEL MUDGUARD RH

Hide 51903B 16.INSTALL SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)

Hide 51902A 17.INSTALL SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)

Hide 51937C 18.INSTALL SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)

Hide 51980A 19.INSTALL PINTLE HOOK ASSEMBLY

a.

Install the pintle hook assembly and pintle hook bracket with the 2 bolts, 2 eyelet pintle hooks and 4 nuts.

Torque:
for nut : 65 N*m (663 kgf*cm, 48 ft.*lbf)


b.

For vehicles with a spare installed to the underbody, install the spare tire.