Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › BLACK OUT TAPE (for Front Door) › from 2015.08
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255851 BLACK OUT TAPE(for Front Door) A

EXTERIOR PANELS / TRIM  BLACK OUT TAPE(for Front Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

When installing the No. 1 black out tape LH, No. 3 black out tape LH, No. 4 black out tape LH and front door rear window frame moulding LH, heat the vehicle body, No. 1 black out tape LH, No. 3 black out tape LH, No. 4 black out tape LH and front door rear window frame moulding LH using a heat light.



Standard Heating Temperature:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
No. 1 Black Out Tape LH 20 to 30°C (68 to 86°F)
No. 3 Black Out Tape LH 20 to 30°C (68 to 86°F)
No. 4 Black Out Tape LH 20 to 30°C (68 to 86°F)
Front Door Rear Window Frame Moulding LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body, No. 1 black out tape LH, No. 3 black out tape LH, No. 4 black out tape LH and front door rear window frame moulding LH excessively.


PROCEDURE

Hide 1.REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape up to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape down to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in high temperature places.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for flat surfaces)

NOTICE:
·

Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms and will not fit after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee at 40 to 50° (for pressing forward) or 30 to 45° (for pulling) to the vehicle body surface and press the tape onto the vehicle body surface with a force of 20 to 30 N (2 to 3 kgf) at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

B147252E32
0.104,0.083 3.417,1.583 3.313,1.5 2.26,0.25 2.198,0.25 2.198,0.25 2.052,0.698 false 1.396,1.146 1.396,1.302 false 0.792,0.396 0.688,0.583 false 5.063,2.573 4.854,2.573 false 1.854,3.521 2.01,3.521 false 0.792,0.396 0.896,0.396 false 1.698,3.208 1.531,3.083 1.531,3.083 1.458,3.083 false 5.188,3.177 5.094,3.125 5.094,3.125 4.771,3.125 false 2.031,2.302 1.729,2.604 1.729,2.604 1.458,2.604 false 5.656,2.625 5.979,2.948 5.979,2.948 6.135,2.948 false 2.188,1.99 2.188,1.688 2.188,1.688 2.594,1.688 false 5.583,3.448 5.417,3.448 false 0.167,0.125 0.51,0.396 0.344,0.271 10 false *a 2.667,1.625 3.302,1.854 0.635,0.229 10 false 40 to 50° 6.198,2.844 6.865,3.063 0.667,0.219 10 false 30 to 45° 0.729,2.229 1.646,2.458 0.917,0.229 10 false 3 to 7 cm/sec. 4.115,2.229 5.083,2.438 0.969,0.208 10 false 3 to 7 cm/sec. 2.833,2.469 4.052,3.021 1.219,0.552 10 false 10 to 20 mm 6.031,2.542 7.115,2.771 1.083,0.229 10 false 10 to 20 mm 1.292,3.01 1.521,3.188 0.229,0.177 10 false *1 1.677,3.438 1.875,3.646 0.198,0.208 10 false *e 1.281,2.521 1.51,2.729 0.229,0.208 10 false *d 0.146,1.646 0.49,1.917 0.344,0.271 10 false *A 0.948,0.323 1.292,0.594 0.344,0.271 10 false *d 2.323,0.177 2.667,0.448 0.344,0.271 10 false *b 1.333,1.333 1.594,1.531 0.26,0.198 10 false *c 3.927,1.615 4.271,1.885 0.344,0.271 10 false *B 4.667,2.49 4.906,2.667 0.24,0.177 10 false *d 4.594,3.063 4.781,3.229 0.188,0.167 10 false *1 5.24,3.365 5.583,3.635 0.344,0.271 10 false *e

Text in Illustration
*A Pressing *B Pulling
*1 Black Out Tape - -
*a Sectional View *b Non-padded Side
*c Padded Side *d Squeegee
*e Release Paper - -

NOTICE:

Be sure to observe the specified pressing speed, force, and angle of the squeegee to avoid wrinkles or air bubbles.


HINT:
·

Either angle of the squeegee (for pressing forward or for pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.





f.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces)

i.
B147253E23
1.208,1.75 0.615,1.75 false 0.99,0.5 1.344,0.771 0.354,0.271 10 false *c 1.635,0.365 1.865,0.594 0.229,0.229 10 false *b 2.313,0.469 2.573,0.708 0.26,0.24 10 false *a 0.438,1.667 0.677,1.854 0.24,0.188 10 false *d

Text in Illustration
*a First
*b Second
*c Third
*d Squeegee

If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for corners)

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles on the tape and achieve a neat finish.



h.

Check after installation

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




Hide 75928B 2.INSTALL NO. 4 BLACK OUT TAPE LH

B182615

a.

Refer to the illustration to position a new No. 4 black out tape LH.


b.

Remove the release paper and apply the tape.


Hide 75926A 3.INSTALL NO. 3 BLACK OUT TAPE LH

B182613

a.

Refer to the illustration to position a new No. 3 black out tape LH.


b.

Remove the release paper and apply the tape.


Hide 75922M 4.INSTALL NO. 1 BLACK OUT TAPE LH

B182611E02
0.729,1.824 1.184,2.077 0.455,0.253 10 A - A 1.623,0.498 1.885,0.742 0.262,0.244 10 A 2.024,2.652 2.263,2.826 0.239,0.174 10 *b 1.54,0 1.802,0.244 0.262,0.244 10 A 2.133,2.217 2.372,2.391 0.239,0.174 10 *a

a.

Refer to the illustration to position a new No. 1 black out tape LH.

Standard Dimension:
Area Dimension
*a 2 to 4 mm (0.078 to 0.158 in.)
*b 4 to 6 mm (0.158 to 0.236 in.)



b.

Remove the release paper and apply the tape.


Hide 67862 5.INSTALL FRONT DOOR WEATHERSTRIP LH

a.
B433685

w/o Spot Cover:

i.

Attach the 6 clips and install the upper part of the front door weatherstrip LH.



b.

w/ Spot Cover:

i.

Install the front door weatherstrip LH (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>REASSEMBLY).



Hide 68620 6.INSTALL FRONT DOOR CHECK ASSEMBLY LH

Hide 67674 7.INSTALL LOWER DOOR FRAME GARNISH LH

Hide 75756C 8.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH

Hide 75720 9.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 68151E 10.INSTALL FRONT DOOR GLASS RUN LH

Hide 68102 11.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

Hide 68172A 12.INSTALL FRONT INNER DOOR GLASS WEATHERSTRIP LH

Hide 67832 13.INSTALL FRONT DOOR SERVICE HOLE COVER LH

Hide 87940 14.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 67602 15.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Hide 74646 16.INSTALL DOOR ASSIST GRIP COVER LH

Hide 74232 17.INSTALL FRONT UPPER ARMREST BASE PANEL LH

Hide 69278B 18.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH

Hide 67492A 19.INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH

Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).