Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2015.08
RM2660E _59 Vehicle Exterior _052852 DOOR / HATCH _0255747 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.



PROCEDURE

Hide 67862 1.INSTALL FRONT DOOR WEATHERSTRIP LH

HINT:

When installing the front door weatherstrip, heat the vehicle body and front door weatherstrip using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front Door Weatherstrip 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or front door weatherstrip excessively.


a.

w/ Spot Cover:

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.


iv.

Using a heat light, heat the vehicle body and a new front door weatherstrip LH.


v.

Remove the peeling paper from the face of the front door weatherstrip LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



vi.

Attach the 21 clips to install a new front door weatherstrip LH.

HINT:
·

If clips are damaged during installation, replace them.

·

Press the front door weatherstrip LH firmly to install it.





b.

w/o Spot Cover:

i.

Attach the 21 clips to install the front door weatherstrip LH.

HINT:

If clips are damaged during installation, replace them.




Hide 68620 2.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.

Install the front door check assembly LH to the door panel with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 67924 3.INSTALL FRONT NO. 2 DOOR STIFFENER CUSHION

HINT:

When installing the front No. 2 door stiffener cushion, heat the vehicle body and front No. 2 door stiffener cushion using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Front No. 2 Door Stiffener Cushion 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or front No. 2 door stiffener cushion excessively.


a.

Clean the installation surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new front No. 2 door stiffener cushion.

i.

Using a heat light, heat the vehicle body and a new front No. 2 door stiffener cushion.


ii.

Remove the peeling paper from the face of the front No. 2 door stiffener cushion.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Attach the 2 clamps to install the door stiffener cushion.

HINT:

Press the front No. 2 door stiffener cushion firmly to install it.



iv.

Install the 2 bolts.



Hide 69312 4.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.
B433938E02
2.312,1.302 2.529,1.513 0.218,0.211 2.306,1.314 2.493,1.495 0.187,0.181 10 (1) 1.61,1.219 1.797,1.400 0.187,0.181 10 (2)

Install the front door lock open rod LH as shown in the illustration.


Hide 89746D 5.INSTALL NO. 2 ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)

a.

Attach the 2clamps and guide to install the No. 2 electrical key wire harness to the front door outside handle frame sub-assembly LH.


Hide 69202A 6.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding areas of the front door outside handle frame sub-assembly LH.


b.

Attach the nut and 2 guides to install the front door outside handle frame sub-assembly LH.


c.

Attach the clamp.


d.
B433939E03
2.042,2.156 2.531,2.156 false 0.281,1.958 0.531,1.958 false 1.073,1.792 1.073,1.552 1.073,1.552 0.917,1.552 false 0.406,2.51 0.656,2.51 0.656,2.51 0.656,2.25 false 2.552,2.083 2.708,2.26 0.156,0.177 10 false *b 0.094,1.865 0.25,2.042 0.156,0.177 10 false *c 0.281,2.427 0.448,2.656 0.167,0.229 10 true *c 0.719,1.448 0.917,1.75 0.198,0.302 10 true *a

Using a T30 "TORX" wrench, install the front door outside handle frame sub-assembly LH with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)

NOTICE:

A cover should be inserted between the screw and door panel.



Hide 69760C 7.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B237389

Install the front door inside locking cable assembly LH.


b.

Attach the 3 claws.


Hide 69720B 8.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the front door lock remote control cable assembly LH.


Hide 69320 9.INSTALL FRONT DOOR LOCK ASSEMBLY LH

Hide 69254C 10.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD LH

a.

Attach the 2 claws to install the front door rear outside handle pad LH.


Hide 69252 11.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

a.

Attach the 3 claws to install the front door front outside handle pad LH.


Hide 69220 12.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B433940

Pull and hold the bellcrank lever of the front door outside handle frame sub-assembly LH.


b.

Install the front door outside handle assembly LH by pushing it in the direction of the arrow in the illustration.


c.

w/ Entry and Start System:

i.
B433941

Attach the 3 claws to install the connector and connector cover.



Hide 69217F 13.INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH

a.

Apply MP grease to the sliding and rotating areas of the front door lock cylinder.


b.
B433942

Attach the 2 claws to install the front door outside handle cover LH to the front door lock cylinder.


c.

Using a T30 ''TORX'' socket, install the front door outside cover LH (with the door lock cylinder) with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

Install the hole plug.


Hide 85720C 14.INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69802 15.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B180836E19
2.177,0.896 1.604,0.698 false 2.479,1.521 2.635,1.74 0.156,0.219 10 true 1 1.927,0.875 2.104,1.063 0.177,0.188 10 true 4 2.771,1.51 2.979,1.708 0.208,0.198 10 true 3 2.115,1.594 2.25,1.833 0.135,0.24 10 true 6 1.313,1.458 1.448,1.646 0.135,0.188 10 true 5 3.229,0.906 3.375,1.229 0.146,0.323 10 true 2 1.417,0.604 1.646,0.813 0.229,0.208 10 true *a

Apply MP grease to the sliding and rotating areas of the front door window regulator sub-assembly LH.

NOTICE:

Do not apply grease to the spring of the front door window regulator sub-assembly LH.


Text in Illustration
*a Temporary Bolt


b.

Loosely install the temporary bolt onto the front door window regulator sub-assembly LH.


c.

Insert the front door window regulator sub-assembly LH into the door panel. Use the temporary bolt to hang the front door window regulator sub-assembly LH on the door panel.

NOTICE:

Be careful not to drop the front door window regulator sub-assembly LH as it may become damaged.



d.

Temporarily install the front door window regulator sub-assembly LH with the 5 bolts.


e.

Tighten the 6 bolts in the order shown in the illustration.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 75756C 16.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH

Hide 75720 17.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY LH

Hide 67674 18.INSTALL LOWER DOOR FRAME GARNISH LH

a.

Attach the clip and install a new lower door frame garnish LH.


Hide 67404F 19.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.

Attach the guide.


b.

Install the front door rear lower frame sub-assembly LH with the bolt.


Hide 68151E 20.INSTALL FRONT DOOR GLASS RUN LH

a.

Install the front door glass run LH.


Hide 68102 21.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Temporarily install the multiplex network master switch assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Move the front door window regulator sub-assembly LH so that the front door glass sub-assembly LH bolts can be seen.


d.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:
·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



e.

Disconnect the multiplex network master switch assembly.


f.
B183141

Insert the front door glass sub-assembly LH into the door panel along the glass run as indicated by the arrows in the illustration.

NOTICE:

Be careful not to damage the glass.



g.

Install the front door glass sub-assembly LH to the front door window regulator sub-assembly LH with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 67832 22.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.
B180831

Apply butyl tape to the door.


b.

Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.

NOTICE:
·

When installing the front door service hole cover LH, pull the links and connectors through the front door service hole cover LH.

·

There should be no wrinkles or folds after attaching the front door service hole cover LH.

·

After attaching the front door service hole cover LH, check the sealing quality.




c.
B186231E05
2.427,1.51 2.698,1.75 0.271,0.24 10 false 45° 3.073,1.5 3.344,1.74 0.271,0.24 10 false 45°

Connect the 2 connectors.


d.

Attach the 9 clamps.


e.

Install the bolt as shown in the illustration.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 89860A 23.INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH (w/ Curtain Shield Airbag)

Hide 67856B 25.INSTALL FRONT DOOR PANEL PROTECTOR LH

a.

Install the screw, and install the front No. 1 door stiffener cushion and front door panel protector LH.


Hide 89430 26.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)

Hide 87940 27.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 82505A 28.REMOVE FRONT DOOR WIRING SUB-ASSEMBLY

a.

Attach the 2 clamps to install the front door wiring sub-assembly to the front door inside handle bezel LH.


Hide 69278E 29.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH

a.

Install the front door inside handle bezel LH to the trim board with the 8 screws.


Hide 69206B 30.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.

Attach the 2 claws to install the front door inside handle sub-assembly LH.


Hide 84927 31.INSTALL SEAT MEMORY SWITCH (w/ Seat Position Memory System)

Hide 68172A 32.INSTALL FRONT INNER DOOR GLASS WEATHERSTRIP LH

a.
B180828

Attach the 4 claws to install the front inner door glass weatherstrip LH.


Hide 67602 33.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B183139

Connect the connector.


b.

Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH to the front door inside handle sub-assembly LH.


c.
B433943

Attach the 4 claws and 13 clips to install the front door trim board sub-assembly LH.


d.

Install the 3 screws.


Hide 74646 34.INSTALL DOOR ASSIST GRIP COVER LH

a.

Attach the 8 claws to install the door assist grip cover LH to the front door trim board sub-assembly LH.


Hide 84040 35.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

Hide 74232 36.INSTALL FRONT UPPER ARMREST BASE PANEL LH

Hide 69278B 37.INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH

a.
B183136

Attach the 4 claws to install the front door inside handle bezel LH.


Hide 81230 38.INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Hide 67492A 39.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.

Attach the clip and claw, and install the front door lower frame bracket garnish LH.


Hide 75072A 40.INSTALL FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH (w/ Outside Moulding)

Hide 41.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).