The tire pressure warning valve and transmitters that are installed in the tire and wheel assemblies measure the tire pressures. The measured values are transmitted to the tire pressure warning ECU and receiver in the vehicle as radio waves. The ECU compares the measured air pressure values with the air pressure threshold. When the measured air pressure value is less than this threshold, the warning light in the combination meter assembly illuminates.
The tire pressure warning valve and transmitters constantly send radio waves to the tire pressure warning ECU and receiver.
Under the conditions below, the tire pressure warning ECU and receiver is unable to receive the signals from the tire pressure warning valve and transmitters, and a DTC is stored.
Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
Devices using similar radio frequencies are used in the vehicle.
The ID of a tire pressure warning valve and transmitter is mistyped during registration.
A tire, wheel and/or transmitter from a different vehicle is installed.
When no transmitter ID is received from a tire pressure warning valve and transmitter for 20 minutes*1 (10 minutes*2) or more while the vehicle speed is more than 40 km/h (25 mph), or no transmitter ID is received from any of the tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2) or more, DTCs from C2121/21 to C2125/25 are stored.
DTCs C2121/21 to C2125/25 can only be cleared by using the GTS. DTCs C2181/81 to C2185/85 can be cleared when the tire pressure warning valve and transmitter sends a forced transmission signal or test mode ends. DTCs C2181/81 to C2185/85 are output only in test mode.
*1: for FMVSS138 Type
*2: for ECE-R64 Type
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C2121/21
C2122/22 C2123/23 C2124/24 C2125/25 |
Following condition (a) or (b) is met:
(a) When all conditions below are met: ·
Tire pressure warning valve and transmitter is not in stop mode. ·
Any transmitter ID is not received from tire pressure warning valve and transmitters. ·
Vehicle speed is more than 40 km/h (25 mph) or no vehicle speed signal is received for 20 minutes*1 (10 minutes*2) or more. (b) When both conditions below are met: ·
Tire pressure warning valve and transmitter is not in stop mode. ·
No transmitter ID is received from tire pressure warning valve and transmitters for 20 minutes*1 (10 minutes*2) or more. |
·
Tire pressure warning valve and transmitter ·
Tire pressure warning antenna*3 ·
Tire pressure warning ECU and receiver |
| C2181/81
C2182/82 C2183/83 C2184/84 C2185/85 |
Test mode procedure is performed. | ·
Tire pressure warning valve and transmitter ·
Tire pressure warning antenna*3 ·
Tire pressure warning ECU and receiver |
*1: for FMVSS138 Type
*2: for ECE-R64 Type
*3: w/ Front Antenna
w/ ID Switching Function:
(Main) is displayed on the DTC screen for the DTCs even when the 2nd set of tires is selected.
When DTCs C2121/21 to C2125/25 are stored, DTC C2179/79 may be stored simultaneously. In such cases, troubleshoot DTCs C2121/21 to C2125/25 first, then troubleshoot DTC C2179/79.
It is necessary to perform the following procedure to identify the tire pressure warning valve and transmitter that is malfunctioning because it cannot be identified by the output DTC.
When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.
It is necessary to perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION) after registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION) of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.
Check that the following conditions are not met:
Facilities or devices that use similar radio frequencies are located in the vicinity of the vehicle.
If the vehicle is located in an area such as the one described above, the tire pressure warning light may come on only in a particular area.
Devices using similar radio frequencies are used in the vehicle.
Facilities or devices that use similar radio frequencies are not located in the vicinity of the vehicle.
Radio transmissions may be interrupted due to the surroundings or devices installed by the user.
| Result | Proceed to |
|---|---|
| OK (w/ Front Antenna) | A |
| OK (w/o Front Antenna) | B |
| NG | C |
A
B
C
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.
Perform the test mode inspection (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TEST MODE PROCEDURE).
| Result | Proceed to |
|---|---|
| DTC C2195/95 is cleared | A |
| DTC C2195/95 is not cleared | B |
A
B
Set the tire pressure to the specified values (See page Suspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION).
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Display the "ID Tire Inflation Pressure" value for each wheel using the GTS.
Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kg/cm2, 5.8 psi) within 30 seconds. If the "ID Tire Inflation Pressure" value displayed on the GTS does not change, the tire pressure warning valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" value was the cause of the output DTC.
Identify the malfunctioning tire pressure warning valve and transmitter by repeatedly decreasing the tire pressure for each tire.
Record which "ID Tire Inflation Pressure" value corresponds to each tire.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 5 Tire Inflation Pressure | ID5 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
*: It may take a few minutes until the values are displayed.
The wheel position cannot be determined from ID1 through ID5 on the Data List.
Check the Data List.
It may take a few minutes to display the updated tire pressure data.
When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.
Record the transmitter ID of which "ID Tire Inflation Pressure" values corresponds to each tire.
After confirming that the "ID Tire Inflation Pressure" value for one tire has changed, repeat this procedure for each tire. Identify the transmitter that corresponds to the DTC.
| Result | Proceed to |
|---|---|
| One or more transmitters are abnormal | A |
| All transmitters are normal | B |
A
B
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Registered ID 1 code | Registered ID1 code/
min.: 0 max.: FFFFFFF* |
ID No. registered for transmitter ID1 displayed | - |
| Registered ID 2 code | Registered ID2 code/
min.: 0 max.: FFFFFFF* |
ID No. registered for transmitter ID2 displayed | - |
| Registered ID 3 code | Registered ID3 code/
min.: 0 max.: FFFFFFF* |
ID No. registered for transmitter ID3 displayed | - |
| Registered ID 4 code | Registered ID4 code/
min.: 0 max.: FFFFFFF* |
ID No. registered for transmitter ID4 displayed | - |
| Registered ID 5 code | Registered ID5 code/
min.: 0 max.: FFFFFFF* |
ID No. registered for transmitter ID5 displayed | - |
*: Displayed only when the ID No. is not registered.
The wheel position cannot be determined from ID1 through ID5 on the Data List.
Check the ID number on the identified transmitter by removing it from the tire and wheel.
| *1 | Tire Pressure Warning Valve and Transmitter | - | - |
| *a | Transmitter ID (7-digit Number) | *b | Wheel Speed Type Tire Inflation Pressure Display Function Identification Mark |
Be sure to use tire pressure warning valve and transmitters with identification marks for this model.
Confirm that the ID number on the transmitter and recorded transmitter ID match.
| Result | Proceed to |
|---|---|
| Match | A |
| Do not match | B |
A
B
Replace the tire pressure warning valve and transmitter (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING VALVE>REMOVAL).
NEXT
Perform registration (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION).
NEXT
Perform initialization (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION).
NEXT
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Tire Pressure Monitor / Data List.
Check the values by referring to the table below.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| ID 1 Tire Inflation Pressure | ID1 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 2 Tire Inflation Pressure | ID2 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 3 Tire Inflation Pressure | ID3 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 4 Tire Inflation Pressure | ID4 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
| ID 5 Tire Inflation Pressure | ID5 tire inflation pressure/
min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure (Gauge) / 0 kPa (0 kgf/cm2, 0 psi) max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), Relative pressure (Gauge) / 380 kPa (3.9 kgf/cm2, 55 psi) |
Actual tire inflation pressure | If N/A is displayed, data has not been received.* |
*: It may take a few minutes until the values are displayed.
The wheel position cannot be determined from ID1 through ID5 on the Data List.
When an "ID Tire Inflation Pressure" value has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the value.
| Result | Proceed to |
|---|---|
| Tire pressure values are not displayed. | A |
| All tire pressure readings are equal to specified values. | B |
A
B