Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › 2016.08–2019.08
RM2660E _53 Suspension _052817 TIRE PRESSURE MONITORING _0255402 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals 13 (TC) and 4 (CG) of the DLC3. The DTCs are indicated by the blinking of the tire pressure warning light.

WIRING DIAGRAM

C281618E05
6.042,1.052 6.594,1.5 0.552,0.448 10 false PRG*1, PRG2*2 3.771,1.135 4.167,1.292 0.396,0.156 10 false PRG 5.365,1.979 6.74,2.135 1.375,0.156 10 false L65*1, L75*2 5.833,1.021 6.021,1.177 0.188,0.156 10 false 5 4.188,1.021 4.375,1.177 0.188,0.156 10 false 5 1.354,2.667 1.865,3.021 0.51,0.354 10 false 16*3,*7, 27*4 6.042,3.073 6.25,3.229 0.208,0.156 10 false TC 1.073,3.094 1.281,3.25 0.208,0.156 10 false TC 5.76,2.99 5.938,3.146 0.177,0.156 10 false 13 5.844,3.615 5.948,3.771 0.104,0.156 10 false 4 6.042,3.708 6.281,3.865 0.24,0.156 10 false CG 6.198,4.24 6.615,4.427 0.417,0.188 10 false E22 6.198,4.375 6.583,4.531 0.385,0.156 10 false DLC3 5.365,2.146 7.115,2.49 1.75,0.344 10 false Tire Pressure Warning ECU and Receiver 2.99,1.938 3.51,2.094 0.521,0.156 10 false E118 2.99,2.104 4.74,2.448 1.75,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 0.729,4.25 1.104,4.406 0.375,0.156 10 false ECM 1.427,3.083 1.708,3.24 0.281,0.156 10 false A38 1.865,3.083 2.146,3.24 0.281,0.156 10 false A52 2.063,4.667 3.146,4.823 1.083,0.156 10 false *3: for 1UR-FE 2.063,4.979 4.135,5.135 2.073,0.156 10 false *4: for 1VD-FTV 1.479,3.302 1.667,3.458 0.188,0.156 10 false *5 1.917,3.302 2.104,3.458 0.188,0.156 10 false *6 2.031,6.354 4.115,6.51 2.083,0.156 10 false : CAN Communication Line 2.063,3.979 4.594,4.333 2.531,0.354 10 false *1: w/o Front Antenna 2.063,4.313 4.833,4.625 2.771,0.313 10 false *2: w/ Front Antenna 1.885,2.667 2.271,3.021 0.385,0.354 10 false 16*3, 27*4 2.063,5.302 3.146,5.458 1.083,0.156 10 false *5: for LHD 2.063,5.625 3.146,5.781 1.083,0.156 10 false *6: for RHD 2.094,5.948 3.625,6.146 1.531,0.198 10 false *7: 1GR-FE

PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output (for LHD with Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM, for LHD without Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM, for RHD with Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM, for RHD without Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
DTC is not output. A
DTC is output. for LHD with Central Gateway ECU B
for LHD without Central Gateway ECU C
for RHD with Central Gateway ECU D
for RHD without Central Gateway ECU E




A

2.CHECK DTC (C2179/79)

B

C

D

E

2.CHECK DTC (C2179/79)
a.

Check if DTC C2179/79 is output (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>C2179/79).

Result:
Result Proceed to
DTC C2179/79 is not output. A
DTC C2179/79 is output. B




A

3.INSPECT DLC3 (TC VOLTAGE)

B

3.INSPECT DLC3 (TC VOLTAGE)
a.
U156225E08
1.781,1.469 2.031,1.802 true 1.573,1.073 1.365,1.802 true 0.156,0.083 0.833,0.365 0.677,0.281 10 false *a 1.969,1.833 2.49,2.01 0.521,0.177 10 false TC 1.198,1.813 1.552,1.99 0.354,0.177 10 false CG 1.531,0.396 1.896,0.583 0.365,0.188 10 false E22

Turn the ignition switch off.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E22-13 (TC) - E22-4 (CG) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of DLC3



OK

4.REPLACE ECM

NG

5.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
4.REPLACE ECM
SST
09843-18040  

a.

Turn the ignition switch off.



U156225E08
1.781,1.469 2.031,1.802 true 1.573,1.073 1.365,1.802 true 0.156,0.083 0.833,0.365 0.677,0.281 10 false *a 1.969,1.833 2.49,2.01 0.521,0.177 10 false TC 1.198,1.813 1.552,1.99 0.354,0.177 10 false CG 1.531,0.396 1.896,0.583 0.365,0.188 10 false E22

Text in Illustration
*a Front view of DLC3

c.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


d.

Turn the ignition switch to ON.


e.

Check that the tire pressure warning light is blinking.

OK:

The tire pressure warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

END

NG

REPLACE TIRE PRESSURE WARNING ECUAND RECEIVER

5.CHECK HARNESS AND CONNECTOR (TC of DLC3 - ECM)
a.

Turn the ignition switch off.


b.

Disconnect the A38*1 or A52*2 ECM connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1UR-FE
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-16 (TC)*1
E22-13 (TC) - A52-16 (TC)*2
Always Below 1 Ω
E22-13 (TC) or A38-16 (TC)*1 - Body ground
E22-13 (TC) or A52-16 (TC)*2 - Body ground
Always 10 kΩ or higher

for 1VD-FTV
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-27 (TC)*1
E22-13 (TC) - A52-27 (TC)*2
Always Below 1 Ω
E22-13 (TC) or A38-27 (TC)*1 - Body ground
E22-13 (TC) or A52-27 (TC)*2 - Body ground
Always 10 kΩ or higher

for 1GR-FE
Tester Connection Condition Specified Condition
E22-13 (TC) - A38-16 (TC)*1 Always Below 1 Ω
E22-13 (TC) or A38-16 (TC)*1 - Body ground Always 10 kΩ or higher


*1: for LHD

*2: for RHD




OK

6.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
U156226E02
1.573,1.083 1.365,1.813 true 0.156,0.083 0.833,0.365 0.677,0.281 10 false *a 1.26,1.813 1.615,1.99 0.354,0.177 10 false CG 1.542,0.396 1.906,0.583 0.365,0.188 10 false E22

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E22-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of DLC3



OK

7.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE ECM
SST
09843-18040  

a.

Turn the ignition switch off.



U156225E08
1.781,1.469 2.031,1.802 true 1.573,1.073 1.365,1.802 true 0.156,0.083 0.833,0.365 0.677,0.281 10 false *a 1.969,1.833 2.49,2.01 0.521,0.177 10 false TC 1.198,1.813 1.552,1.99 0.354,0.177 10 false CG 1.531,0.396 1.896,0.583 0.365,0.188 10 false E22

Text in Illustration
*a Front view of DLC3

c.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.


d.

Turn the ignition switch to ON.


e.

Check that the tire pressure warning light is blinking.

OK:

The tire pressure warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (See page Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>PROBLEM SYMPTOMS TABLE).




OK

END

NG

REPLACE TIRE PRESSURE WARNING ECUAND RECEIVER