For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).
These DTCs are related to the air fuel ratio sensor, although the titles say oxygen sensor.
The air fuel ratio sensor outputs a voltage* that is proportional to the air-fuel ratio. The air fuel ratio sensor output voltage is used to control the A/F mixture.
The air fuel ratio sensor is located after the Diesel Particulate Filter (DPF) catalytic converter. This sensor has been developed based on the structure and technology of the air fuel ratio sensor that is used for gasoline engines. The cover for the sensor electrode has been modified to suit its application in a diesel engine. This change allows the sensor to function effectively in this DPF type diesel engine, and it also avoids problems with sensor temperature and particulate matter (PM).
In order to reduce PM, the ECM adjusts the air-fuel ratio to a value slightly richer than that which would otherwise be used (note that this mixture is still leaner than the stoichiometric air fuel ratio). The ECM controls these adjustments on signals from the air fuel ratio sensor.
When the ECM performs PM forced regeneration (cleaning) by adding fuel using the exhaust fuel addition injector assembly, the air fuel ratio sensor feedback is used to ensure that an appropriate air fuel ratio is maintained.
*: This voltage change occurs only inside the ECM. It is not possible to measure this voltage at the sensor. The GTS can be used to monitor this voltage.
The ECM provides a pulse width modulated control circuit to adjust current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
·
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more. ·
Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the GTS. |
Air fuel ratio sensor heater current is 0.8 A or less when the heater operates for 4 seconds.
(1 trip detection logic) |
·
Open in air fuel ratio sensor heater circuit ·
air fuel ratio sensor heater ·
A/F relay ·
ECM |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
|---|---|---|
| Ignition switch ON for 5 seconds | Either condition is met (1 trip detection logic):
·
Air fuel ratio sensor heater current reaches the high limit (overcurrent is detected even though the air fuel ratio sensor heater is off) ·
Air fuel ratio sensor heater current is 0.8 A or more when the heater does not operate for 4 seconds. |
·
Short in air fuel ratio sensor heater circuit ·
Air fuel ratio sensor heater ·
ECM |
| DTC No. | Data List |
|---|---|
| P0031
P0032 |
·
AFS Voltage B1S1 ·
AF Lambda B1S1 ·
Exhaust Temperature B1S1 |
| P0052
P0053 |
·
AFS Voltage B2S1 ·
AF Lambda B2S1 ·
Exhaust Temperature B2S1 |
The inner surface of the air fuel ratio sensor element is exposed to outside air. The outer surface of the sensor element is exposed to exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations of the exhaust and the outside air. The platinum coating amplifies the voltage generation. When heated, the sensor becomes very efficient. If the temperature of the exhaust is low, without supplemental heating, the sensor will not generate useful voltage signals. The ECM controls the heating by using a duty-cycle to regulate the average current in the heater element. If the heater current is out of the normal range, the output signals of the sensor are inaccurate and the ECM cannot regulate the air-fuel ratio properly. When the heater current is out of the normal operating range, the ECM interprets this as a malfunction and stores a DTC.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the air fuel ratio sensor (for bank 1 or bank 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION).
OK
NG
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C159-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| C158-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | for Bank 1 |
| *B | for Bank 2 |
| *a | Front view of wire harness connector
(to Air Fuel Ratio Sensor) |
OK
NG
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C159-1 (HAF1) - C45-45 (HA1A) | Always | Below 1 Ω |
| C158-1 (HAF2) - C45-46 (HA2A) | Always | Below 1 Ω |
| C159-1 (HAF1) or C45-45 (HA1A) - Body ground | Always | 10 kΩ or higher |
| C158-1 (HAF2) or C45-46 (HA2A) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C159-1 (HAF1) - C46-45 (HA1A) | Always | Below 1 Ω |
| C158-1 (HAF2) - C46-46 (HA2A) | Always | Below 1 Ω |
| C159-1 (HAF1) or C46-45 (HA1A) - Body ground | Always | 10 kΩ or higher |
| C158-1 (HAF2) or C46-46 (HA2A) - Body ground | Always | 10 kΩ or higher |
OK
NG
Replace the ECM (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECM>REMOVAL).
NEXT
Disconnect the air fuel ratio sensor connector.
Remove the integration relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C159-2 (+B) - 1S-3 | Always | Below 1 Ω |
| C158-2 (+B) - 1S-3 | Always | Below 1 Ω |
| C159-2 (+B) or 1S-3 - Body ground | Always | 10 kΩ or higher |
| C158-2 (+B) or 1S-3 - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the integration relay (EFI MAIN NO.2, A/F) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
When DTC P0031 or P0032 is output:
Replace the air fuel ratio sensor (for bank 1) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).
When DTC P0051 or P0052 is output:
Replace the air fuel ratio sensor (for bank 2) (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL).
NEXT
Replace the integration relay (EFI MAIN NO.2, A/F).
NEXT
Repair or replace harness or connector.
NEXT
Check the ECM power source circuit (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>ECM Power Source Circuit).
NEXT
Connect the GTS to the DLC3.
Clear the DTCs (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DTC CHECK / CLEAR).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Turn the GTS on.
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
"Exhaust Temperature B1S1" and "Exhaust Temperature B2S1" on the GTS screen should be 200°C (392°F) or higher.
Confirm that the DTC is not output again.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Engine and ECT / Utility / All Readiness.
Input DTC P0031, P0032, P0052 or P0053.
Check that STATUS is NORMAL.
If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.
If STATUS is INCOMPLETE or N/A, DTC judgment is incomplete. Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more again.
NEXT