When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes current to flow to the coil, closing the contacts of the integration relay (EFI relay) and supplying power to terminal +B of the ECM.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>INITIALIZATION).
Remove the integration relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1X-1 - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(Integration relay) |
OK
NG
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1S-4 - Body ground | Always | Below 1 Ω |
OK
NG
Inspect the integration relay (See page Engine / Hybrid System>1VD-FTV (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Remove the integration relay from the engine room relay block.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-44 (MREL) - 1S-8 | Always | Below 1 Ω |
| A38-2 (+B) - 1S-11 | Always | Below 1 Ω |
| A38-1 (+B2) - 1S-11 | Always | Below 1 Ω |
| A38-44 (MREL) or 1S-8 - Body ground | Always | 10 kΩ or higher |
| A38-2 (+B) or 1S-11 - Body ground | Always | 10 kΩ or higher |
| A38-1 (+B2) or 1S-11 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-44 (MREL) - 1S-8 | Always | Below 1 Ω |
| A52-2 (+B) - 1S-11 | Always | Below 1 Ω |
| A52-1 (+B2) - 1S-11 | Always | Below 1 Ω |
| A52-44 (MREL) or 1S-8 - Body ground | Always | 10 kΩ or higher |
| A52-2 (+B) or 1S-11 - Body ground | Always | 10 kΩ or higher |
| A52-1 (+B2) or 1S-11 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C45-81 (E1) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C46-81 (E1) - Body ground | Always | Below 1 Ω |
OK
NG
Disconnect the ECM connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A38-28 (IGSW) - C45-81 (E1) | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A52-28 (IGSW) - C46-81 (E1) | Ignition switch ON | 11 to 14 V |
OK
NG
Disconnect the ECM connector.
Remove the integration relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-28 (IGSW) - 1P-7 | Always | Below 1 Ω |
| A38-28 (IGSW) or 1P-7 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A52-28 (IGSW) - 1P-7 | Always | Below 1 Ω |
| A52-28 (IGSW) or 1P-7 - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (w/ Entry and Start System) | A |
| OK (w/o Entry and Start System) | B |
| NG | C |
A
B
C
Disconnect the smart key ECU assembly connector.
Disconnect the integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E128-3 (IG1D) - 1R-2 | Always | Below 1 Ω |
| E128-3 (IG1D) or 1R-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the ignition switch assembly connector.
Disconnect the integration relay connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| E93-6 (IG2) - 1R-2 | Always | Below 1 Ω |
| E93-6 (IG2) or 1R-2 - Body ground | Always | 10 kΩ or higher |
OK
NG
Inspect the ignition switch assembly (See page Engine / Hybrid System>1VD-FTV (STARTING)>IGNITION SWITCH>INSPECTION).
OK
(See pageEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>PROBLEM SYMPTOMS TABLE)
NG