Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER(for Standard) › from 2016.08
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255830 REAR BUMPER(for Standard) A

EXTERIOR PANELS / TRIM  REAR BUMPER(for Standard)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

If the bumper is damaged, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (frame, stud bolt) to make sure it is not dented or bent.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK

If the visual inspection finds a problem, check the installation condition of the blind spot monitor sensor, and adjust the installation position of the blind spot monitor sensor as necessary.


PROCEDURE

Hide 51937C 1.REMOVE SPARE WHEEL CARRIER HINGE BRACKET (w/ Tire Carrier)

Hide 51902A 2.REMOVE SPARE WHEEL COVER SUB-ASSEMBLY (w/ Tire Carrier)

Hide 51903B 3.REMOVE SPARE WHEEL CARRIER SUB-ASSEMBLY (w/ Tire Carrier)

Hide 76626E 4.REMOVE REAR QUARTER PANEL MUDGUARD LH

Hide 76625G 5.REMOVE REAR QUARTER PANEL MUDGUARD RH

Hide 52162B 6.REMOVE REAR BUMPER NO. 1 PLATE (for Step)

a.

Put protective tape around the rear bumper No. 1 plate.


b.

Detach the 20 claws and remove the rear bumper No. 1 plate.

B414823E01
3.545,1.669 3.545,1.238 3.545,1.238 3.72,1.238 false 3.762,1.16 3.918,1.341 0.156,0.181 10 *a

Text in Illustration
*a Protective Tape - -


Hide 52159 7.REMOVE REAR BUMPER COVER

HINT:

For the rear bumper cover with tire carrier, use the procedures described below.


a.
B414824E04
1.846,0.84 1.846,0.582 1.846,0.582 2.022,0.582 false 2.026,0.46 2.182,0.641 0.156,0.181 10 *a

Put protective tape around the rear bumper cover.

Text in Illustration
*a Protective Tape


b.
B414825

Open the tail gate and remove the 4 clips.


c.

Close the tail gate.


d.
B414828E06
2.507,1.846 2.507,2.66 false 2.633,2.247 2.633,2.431 2.633,2.431 2.501,2.431 false 2.428,2.667 2.584,2.848 0.156,0.181 10 *a

Remove the 2 bolts, 6 screws and 2 clips.

Text in Illustration
*a Bolt


e.
B414826

Remove the 5 bolts.


f.
B414827

Detach the 7 claws.

HINT:

Use the same procedure for the other side.



g.
B418150

Remove the rear bumper cover.


h.

w/ TOYOTA Parking Assist-sensor System or w/ Rear Fog Light:

Disconnect the No. 2 frame wire connector.


Hide 58724B 8.REMOVE NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

a.
B414832

Remove the 2 screws, 2 grommets and No. 2 luggage compartment side cover protector.


Hide 58723B 9.REMOVE NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

HINT:

Use the same procedure described for the LH side.


Hide 81560 10.REMOVE REAR COMBINATION LIGHT ASSEMBLY LH

Hide 81550 11.REMOVE REAR COMBINATION LIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52563D 12.REMOVE REAR BUMPER UPPER RETAINER LH

a.
B181015

Detach the 2 clips and remove the rear bumper upper retainer LH.


Hide 52562E 13.REMOVE REAR BUMPER UPPER RETAINER RH

HINT:

Use the same procedure described for the LH side.


Hide 52156A 14.REMOVE REAR BUMPER SIDE SUPPORT LH

a.
B414829

Remove the 3 screws.


b.

Detach the 6 claws and remove the rear bumper side support LH.


Hide 52155A 15.REMOVE REAR BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure described for the LH side.


Hide 52172B 16.REMOVE REAR BUMPER NO. 2 REINFORCEMENT

a.
B184217

Remove the 2 bolts and rear bumper No. 2 reinforcement.


Hide 57615C 17.REMOVE REAR BUMPER ARM BRACKET

a.
B414830

Remove the bolt and rear bumper arm bracket.

HINT:

Use the same procedure for both rear bumper arm brackets.



Hide 57616B 18.REMOVE REAR BUMPER ARM BRACKET LH

a.
B414831

Disconnect the clamp.


b.

Remove the 2 bolts and rear bumper arm bracket LH.