Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › from 2016.08
RM2660E _56 Audio / Visual / Telematics _052831 PARK ASSIST / MONITORING _0255516 BLIND SPOT MONITOR SYSTEM D

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  OPERATION CHECK  


BLIND SPOT MONITOR BEAM AXIS CONFIRMATION


HINT:

The blind spot monitor beam axis confirmation is performed to confirm whether the sensor's beam axis is correct, and perform adjustment of the beam axis by using reflector.


a.

When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

E305141E01
4.385,0.844 4.885,0.615 4.885,0.615 5.26,0.604 false 2.135,0.688 2.385,0.688 2.385,0.688 2.76,0.823 false 0.552,0.073 1.896,0.26 1.344,0.188 10 false Left Side of Vehicle: 4.021,0.073 5.365,0.26 1.344,0.188 10 false Right Side of Vehicle: 5.323,0.521 6.667,0.708 1.344,0.188 10 false Vehicle center line 0.969,0.594 2.313,0.781 1.344,0.188 10 false Vehicle center line 1.313,4.375 2.656,4.563 1.344,0.188 10 false : Inspection Area 0.104,2.448 1.052,2.719 0.948,0.271 10 false 5 m (16.41 ft.) 6.208,2.458 7.156,2.729 0.948,0.271 10 false 5 m (16.41 ft.) 3.219,1.823 4.563,2.01 1.344,0.188 10 false Rear Bumper 0.125,1.719 1.073,1.99 0.948,0.271 10 false 1 m (3.28 ft.) 1.531,3.458 2.479,3.729 0.948,0.271 10 false 6 m (19.68 ft.) 4.854,3.458 5.802,3.729 0.948,0.271 10 false 6 m (19.68 ft.) 6.208,1.708 7.156,1.979 0.948,0.271 10 false 1 m (3.28 ft.)

NOTICE:
·

Perform this inspection on level ground.

·

Make sure that there are no metal objects around the vehicle or on the ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.

·

Do not place any objects other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 6 m (19.68 ft.) x L 6 m (19.68 ft.) x H 4 m (13.12 ft.)) shown in the illustration.




b.

Place the reflector.

i.

From the center of the rear bumper (center of the emblem), hang a weight with a pointed tip, and mark position on the ground (mark A).

E338920E01
5.156,1.107 4.876,1.578 4.876,1.578 4.773,1.578 false 5.159,1.624 5.304,1.624 false 5.341,1.537 5.570,1.701 0.229,0.164 10 *a 4.605,1.5 4.834,1.664 0.229,0.164 10 *c 2.456,2.423 2.685,2.587 0.229,0.164 10 *b 4.773,0.267 4.951,0.439 0.178,0.172 10 *d 5.394,0.267 5.572,0.439 0.178,0.172 10 *d 2.76,2.59 2.673,2.504 2.673,2.504 2.617,2.504 false 2.766,2.692 3.122,2.692 false 3.13,2.62 3.380,2.759 0.250,0.140 10 A

Text in Illustration
*a String *b Weight
*c Center point *d Same size

HINT:

Lightly flick the string with your fingers several times to confirm that the string is aligned with mark A.



ii.

From the center of the front bumper (center of the emblem), hang a weight with a pointed tip, and mark position on the ground (mark B).

E338921E01
0.812,1.901 1.110,2.062 0.298,0.161 10 *c 1.758,1.909 2.056,2.070 0.298,0.161 10 *a 3.561,1.976 3.859,2.137 0.298,0.161 10 *b 4.187,2.274 4.484,2.435 0.298,0.161 10 B 1.931,0.209 2.228,0.370 0.298,0.161 10 *d 1.561,1.217 1.109,1.977 1.109,1.977 0.991,1.977 false 1.566,1.991 1.71,1.991 false 3.897,2.229 3.783,2.051 3.783,2.051 3.724,2.051 false 3.912,2.342 4.172,2.342 false

Text in Illustration
*a String *b Weight
*c Center point *d Same size

HINT:

Lightly flick the string with your fingers several times to confirm that the string is aligned with mark (B).



iii.
E238824E01
1.439,1.257 1.206,1.541 false 3.022,1.262 3.177,1.627 false 0.633,1.258 1.092,0.453 false 1.092,0.453 1.292,0.453 false 1.321,0.355 2.528,0.516 1.207,0.161 10 Vehicle center line 1.1,1.532 1.261,1.693 0.161,0.161 10 A 3.186,1.624 3.347,1.785 0.161,0.161 10 B

Draw a vehicle center line so that it passes through mark (A) and (B) (front and rear center points).


iv.

Enlarge and print out the poster shown in the illustration.

E334359E06
2.344,6.031 2.177,6.031 2.177,6.031 2.01,4.458 false 5.063,4.063 4.833,4.063 4.833,4.063 4.615,4.438 false 4.417,6.75 4.25,6.75 4.25,6.75 4.063,7.135 false 3.906,2.625 3.74,2.625 3.74,2.625 3.615,2.354 false 2.427,5.958 2.74,6.271 0.313,0.313 10 false A 4.521,6.677 5.365,6.99 0.844,0.313 10 false Line C 5.188,3.99 6.604,4.219 1.417,0.229 10 false Vehicle center line 2.76,4.021 3.458,4.302 0.698,0.281 10 false 53.5° 3.979,2.583 4.74,2.854 0.76,0.271 10 false Line C 1.396,3.104 2.802,3.396 1.406,0.292 10 false Edge of Rear Bumper 0.229,0.208 0.844,0.438 0.615,0.229 12 false Poster: 2.719,4.688 3.417,4.969 0.698,0.281 10 false 53.5°


v.
E334361E05
1.823,2.771 1.646,3.031 1.646,3.031 1.531,3.031 false 1.99,2.177 2.521,2.552 2.521,2.552 2.729,2.552 false 0.969,1.448 1.135,1.448 1.135,1.448 1.813,1.958 true 0.781,1.375 1.094,1.573 0.313,0.198 10 false A 2.813,2.469 3.313,2.677 0.5,0.208 10 false Poster 0.292,2.948 1.521,3.25 1.229,0.302 10 false Vehicle center line

Attach the printed poster to the floor with the vehicle center line aligned with point A as shown in the illustration.


vi.
E334362E06
0.563,4.125 0.667,4.125 0.667,4.125 0.75,3.75 false 2.875,4.115 2.76,4.115 2.76,4.115 2.656,3.729 false 0.729,3.146 0.833,3.146 0.833,3.146 1.094,3.542 false 2.458,2.594 2.26,2.594 2.26,2.594 1.729,3.167 true 2.604,3.208 2.49,3.208 2.49,3.208 2.292,3.521 false 2,3.74 1.885,3.74 1.885,3.74 1.813,3.396 false 2.073,0.208 1.938,0.208 1.938,0.208 1.698,0.594 false 0.24,0.365 1.219,0.573 0.979,0.208 10 false Vehicle front 2.146,0.125 3.323,0.375 1.177,0.25 10 false Vehicle center line 2.521,2.521 2.875,2.708 0.354,0.188 10 false A 2.688,3.125 3.219,3.323 0.531,0.198 10 false String 0.323,3.042 0.677,3.229 0.354,0.188 10 false String 0.313,4.073 0.667,4.26 0.354,0.188 10 false D 2.917,4.042 3.271,4.229 0.354,0.188 10 false D 2.073,3.667 2.427,3.854 0.354,0.188 10 false Poster

Attach strings aligned with the lines labeled C and mark points D at a distance of 3484 mm (11.43 ft.) from point A.


vii.

Set the reflector at the position (D) shown in the illustration below.

SST
09870-60000  (09870-60010)
09870-60040  

E334360E10
4.417,2.26 4.156,1.802 4.156,1.802 4.01,1.802 false 2.719,2.26 2.979,1.823 2.979,1.823 3.135,1.823 false 2.417,0.729 2.698,0.448 2.698,0.448 2.854,0.448 false 4.76,0.729 5.042,0.448 5.042,0.448 5.198,0.448 false 6,2.969 6.292,3.177 6.292,3.177 6.417,3.177 false 1.177,3 0.969,3.25 0.969,3.25 0.802,3.25 false 1.26,2.896 1.01,2.156 1.01,2.156 0.865,2.156 false 5.906,2.896 6.135,2.302 6.135,2.302 6.292,2.302 false 2.021,2.479 1.74,1.646 1.74,1.646 1.615,1.646 false 5.208,2.521 5.438,1.656 5.438,1.656 5.604,1.656 false 0.573,0.208 1.031,0.406 0.458,0.198 10 false LH: 4.25,0.188 4.708,0.385 0.458,0.198 10 false RH: 3.198,1.719 4.115,1.958 0.917,0.24 10 false Rear bumper 2.917,0.365 4.333,0.708 1.417,0.344 10 false Vehicle center line 5.292,0.365 6.875,0.719 1.583,0.354 10 false Vehicle center line 6.49,3.083 7.083,3.333 0.594,0.25 10 false Reflector 0.188,3.146 0.865,3.417 0.677,0.271 10 false Reflector 0.385,1.552 1.604,1.792 1.219,0.24 10 false 3484 mm (11.43 ft) 5.698,1.583 7.042,1.854 1.344,0.271 10 false 3484 mm (11.43 ft) 0.656,2.073 1.573,2.313 0.917,0.24 10 false D 6.365,2.219 6.813,2.552 0.448,0.333 10 false D

NOTICE:
·
E238830E46
0.198,1.417 0.823,1.823 0.625,0.406 10 false 882 mm (2.89 ft.)

Set the reflector so that its center is 882 mm (2.89 ft) above the ground.

·
E238829E26
1.99,0.667 2.479,1.292 false 2,1.333 3.188,1.781 1.188,0.448 10 false Center of triangular pyramid

The center of triangular pyramid is the reference point for the setting position and angle.

·

Set the reflector as shown in the illustration so that its center of triangular pyramid faces the blind spot monitor sensor.

·

Perform the operation as precisely as possible.





c.

Perform the blind spot monitor beam axis display.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the blind spot monitor main switch (steering pad switch assembly [multi-function switch]) on.


iv.

Turn the GTS on.


v.

Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis display or BSM Slave beam axis display.


vi.

Check the results displayed for the BSM beam axis display.

Allowable Range:
Item Blind Spot Monitor Sensor LH (Master) Blind Spot Monitor Sensor RH (Slave)
Angle -3.6 to +3.6 ° -3.6 to +3.6 °


HINT:

If the results are outside the allowable range, it is possible that the reflector position is incorrect, there is a metallic object near the inspection area or the blind spot monitor sensor installation condition is abnormal, so check the reflector positioning, the inspection area and the blind spot monitor sensor installation condition, and perform the inspection again.



vii.

Perform the blind spot monitor beam axis adjustment using the GTS. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis adjustment or BSM Slave beam axis adjustment.

HINT:

When values on the axis display are in the allowable range, performing this adjustment compensates the values to the normal value.





BLIND SPOT MONITOR INSTALLATION CONDITION INSPECTION


NOTICE:
·

Perform this inspection on level ground.

·

Unload the vehicle before beginning the inspection.

·

Confirm that the tire pressure is correct before beginning the inspection.



HINT:

The blind spot monitor sensor installation condition inspection is performed to confirm whether the sensor is perpendicular to the floor surface (+/-4°) by using a jig, and that the sensor is 46 to 54° from the line parallel to the vehicle center line.



b.

Attach a jig similar to the one shown in the illustration to the outward facing surface of the blind spot monitor sensor and check that the blind spot monitor sensor is perpendicular to the floor surface or within the allowable range.

E233717E01
5.912,3.961 5.912,3.413 false 6.081,3.343 6.913,3.527 0.832,0.184 10 Floor surface 5.912,3.413 6.059,3.413 false 1.953,3.588 1.953,2.446 false 1.189,3.588 2.903,3.753 1.714,0.166 10 Blind Spot Monitor Sensor 3.125,3.441 4.816,3.645 1.691,0.205 10 Outward facing surface 2.298,2.115 2.983,3.504 false 0.161,0.064 1.797,0.248 1.635,0.184 10 Rear view of vehicle (RH): 5.056,1.213 5.582,0.619 false 5.582,0.619 5.729,0.619 false 5.764,0.556 6.208,0.793 0.444,0.236 10 Jig 4.611,3.251 4.874,3.251 false 4.909,3.19 5.483,3.426 0.574,0.236 10 Weight 2.983,3.504 3.095,3.504 false

E308579E03
1.729,0.823 3.302,1.333 1.573,0.51 10 false Hold this side against the blind spot monitor sensor RH 3.917,0.823 5.5,1.313 1.583,0.49 10 false Hold this side against the blind spot monitor sensor LH 3.271,1.719 3.646,1.99 0.375,0.271 10 false Top 1.385,2.677 2.698,3.135 1.313,0.458 10 false Position where string is to be secured 5.344,3.167 5.917,3.646 0.573,0.479 10 false 100 mm (3.94 in.) 2.615,4.385 2.99,4.656 0.375,0.271 10 false A 3.885,4.385 4.26,4.656 0.375,0.271 10 false B 3.104,3.313 3.479,3.583 0.375,0.271 10 false X 3.552,3.313 3.927,3.583 0.375,0.271 10 false Y 1.677,4.99 2.052,5.26 0.375,0.271 10 false + 5,5.021 5.375,5.292 0.375,0.271 10 false - 1.042,6.188 2.5,6.427 1.458,0.24 10 false : Allowable range

Standard
A B
Blind spot monitor sensor RH 5.2 mm
(0.315 in)
-5.2 mm
(-0.315 in)
Blind spot monitor sensor LH 5.2 mm
(0.315 in)
-5.2 mm
(-0.315 in)

X Y
Blind spot monitor sensor RH 3° -3°
Blind spot monitor sensor LH 3° -3°


c.
E305127E09
2.313,0.573 2.625,0.573 2.625,0.573 2.979,1.177 false 1.479,1.938 1.479,1.563 1.479,1.563 1.667,1.563 false 2.031,3.219 2.031,4.01 2.031,4.01 2.219,4.01 false 0.979,3.385 0.708,3.583 0.708,3.583 0.708,3.76 false 1.417,3.427 1.417,3.292 false 0.698,2.01 0.802,2.01 0.802,2.01 0.917,1.729 false 0.115,0.083 1.615,0.354 1.5,0.271 12 false Vehicle rear (LH): 1.063,0.521 2.323,0.729 1.26,0.208 10 false Vehicle center line 1.573,0.948 2.531,1.219 0.958,0.271 10 false Vehicle front 1.74,1.469 2.74,1.823 1,0.354 10 false Stud bolt center line 2.354,2.167 2.948,2.594 0.594,0.427 10 false 108 mm (4.25 in.) 2.563,3.354 3.344,3.635 0.781,0.281 10 false Vehicle rear 2.281,3.927 3.135,4.135 0.854,0.208 10 false Stud bolt 0.135,3.813 1.406,4.177 1.271,0.365 10 false Line parallel to the vehicle center line 1.396,3.469 1.719,3.708 0.323,0.24 10 false y 0.542,1.938 0.865,2.177 0.323,0.24 10 false A

Using the sensor installation stud bolt center lines as a reference, check that the stud bolts are as shown in the illustration.

Standard:
Dimension Specified Value
y 78 to 87 mm
(3.07 to 3.43 in)

Degree Specified Value
A 46 to 54°


HINT:

If the results are not as specified, it is possible that the blind spot monitor sensor installation area (frame, stud bolt) is deformed, so make corrections as necessary.