Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › from 2016.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0660  Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)  


DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

A165943E02
0.066,0.262 1.048,0.439 0.982,0.177 10 Intake Manifold 1.039,0.339 1.419,0.812 false 2.171,0.427 2.556,0.590 0.385,0.163 10 IACV 2.139,0.493 1.856,1.064 false 2.791,2.441 3.141,2.611 0.350,0.170 10 ECM 3.554,2.529 5.078,2.692 1.524,0.163 10 Throttle Position Sensor 2.153,3.107 3.885,3.270 1.732,0.163 10 Crankshaft Position Sensor 5.568,0.138 5.967,0.308 0.399,0.170 10 Close 6.02,1.39 6.433,1.567 0.413,0.177 10 Open 2.868,0.164 4.676,0.355 1.809,0.191 10 Throttle Valve Position (deg.) 5.817,1.883 7.098,2.080 1.281,0.198 10 Engine Speed (rpm) 5.537,0.204 5.397,0.41 false

DTC Code DTC Detection Condition Trouble Area
P0660 Conditions (a) and (b) are met for 0.5 sec. or more (2 trip detection logic):
(a) The voltage of terminal ACIS of the ECM is low when the VSV is OFF.
(b) The engine has started.
·

Open or short in VSV for ACIS circuit

·

VSV for ACIS

·

ECM



WIRING DIAGRAM

A337230E25
0.656,3.823 1.271,4.021 0.615,0.198 10 false Battery 0.583,2.854 1.198,3.052 0.615,0.198 10 false P/I-B 1.375,2.438 3.302,2.865 1.927,0.427 10 false No. 2 Integration Relay 0.698,0.875 1.313,1.073 0.615,0.198 10 false 1X 0.75,0.708 1.365,0.906 0.615,0.198 10 false 1 1.073,1.031 1.74,1.427 0.667,0.396 10 false EFI MAIN NO. 1 1.573,1.646 2.521,1.875 0.948,0.229 10 false EFI-MAIN NO.1 2.417,1.052 3.177,1.281 0.76,0.229 10 false EFI NO.2 3.083,0.875 3.698,1.073 0.615,0.198 10 false 1S 3.125,0.698 3.74,0.896 0.615,0.198 10 false 1 3.094,1.365 3.708,1.563 0.615,0.198 10 false 1S 3.135,1.219 3.75,1.417 0.615,0.198 10 false 4 3.083,2.063 3.698,2.26 0.615,0.198 10 false 1S 3.135,1.896 3.75,2.094 0.615,0.198 10 false 8 6.115,3.74 6.958,4.26 0.844,0.521 10 false ECM 5.417,2.073 6.031,2.271 0.615,0.198 10 false A38 5.49,1.896 6.104,2.094 0.615,0.198 10 false 6 5.417,0.885 6.031,1.083 0.615,0.198 10 false C45 5.417,0.708 6.031,0.906 0.615,0.198 10 false 105 5.75,2.083 6.365,2.281 0.615,0.198 10 false MREL 5.75,0.792 6.365,0.99 0.615,0.198 10 false ACIS 4.135,1.396 5.688,1.844 1.552,0.448 10 false VSV for ACIS 4.115,1.219 4.729,1.417 0.615,0.198 10 false C129 3.979,0.802 4.594,1 0.615,0.198 10 false 1 5.052,0.802 5.333,1.01 0.281,0.208 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE VSV FOR ACIS)
A067588E30
0.469,1.427 0.323,1.667 false 0.667,1.313 0.917,1.802 false 2,1.417 1.844,1.646 false 2.177,1.292 2.5,1.76 false 0.823,0.031 1.531,0.24 0.708,0.208 10 false VSV is ON 2.458,0.031 3.24,0.24 0.781,0.208 10 false VSV is OFF 0.552,0.313 0.771,0.51 0.219,0.198 10 false Air 2.333,1.75 2.813,1.948 0.479,0.198 10 false Port E 0.698,1.781 1.177,1.979 0.479,0.198 10 false Port E 1.625,1.625 2.094,1.823 0.469,0.198 10 false Port F 0.104,1.635 0.573,1.833 0.469,0.198 10 false Port F 2,0.385 2.219,0.583 0.219,0.198 10 false Air 2.76,0.552 3.333,0.75 0.573,0.198 10 false Air Filter

a.

Disconnect the vacuum hose.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG) and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control. Operate the VSV for ACIS.


e.

Check the VSV operation when it is operated using the tester.

Standard:
Tester Operation Specified Condition
VSV ON Air from port E flows out through port F
VSV OFF Air from port E flows out through air filter




OK

2.CHECK VACUUM HOSE

NG

4.INSPECT VSV FOR ACIS (OPERATION)
2.CHECK VACUUM HOSE
a.

Check that the vacuum hose is connected correctly, and that there are no cracks, holes, damage, or looseness.

OK:

Vacuum hose is normal.




OK

3.INSPECT INTAKE MANIFOLD (INTAKE AIR CONTROL VALVE)

NG

REPAIR OR REPLACE VACUUM HOSE

3.INSPECT INTAKE MANIFOLD (INTAKE AIR CONTROL VALVE)

OK

NG

REPLACE INTAKE MANIFOLD (INTAKE AIR CONTROL VALVE)

4.INSPECT VSV FOR ACIS (OPERATION)

OK

5.INSPECT VSV FOR ACIS (POWER SOURCE VOLTAGE)

NG

5.INSPECT VSV FOR ACIS (POWER SOURCE VOLTAGE)
U163743E02
0.115,0.083 2.49,0.417 2.375,0.333 10 false Front view of wire harness connector: (to VSV for ACIS) 0.594,1.198 0.979,1.365 0.385,0.167 10 false C129

a.

Disconnect the VSV for ACIS connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C129-1 - Body ground Engine switch on (IG) 11 to 14 V




OK

6.CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VSV FOR ACIS - INTEGRATION RELAY)

6.CHECK HARNESS AND CONNECTOR (VSV FOR ACIS - ECM)
a.

Disconnect the VSV for ACIS connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance between the terminals of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
C129-2 - C45-105 (ACIS) Always Below 1 Ω
C129-2 or C45-105 (ACIS) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR