32910
1.INSTALL OIL COOLER ASSEMBLY
Install the oil cooler inlet hose and oil cooler outlet hose, connect the air cooled oil cooler tube, and slide the 4 hose clips to secure the hose.
| *a | Lower Side |
| *b | Outward |
Install the rear transmission oil cooler air duct with the 4 bolts, and then install the air cooled oil cooler tube to the rear transmission oil cooler air duct with the bolt.
Temporarily put the oil cooler assembly on the radiator support.
Securely attach the 2 claws of the oil cooler assembly into the holes of the radiator support.
| *a | Claw |
Install the 4 bolts in the sequence shown in the illustration.
32917
2.INSTALL TRANSMISSION OIL COOLER AIR DUCT
Install the transmission oil cooler air duct with the 4 bolts.
32907A
3.INSTALL OIL COOLER TUBE
Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.
32941H
4.INSTALL INLET NO. 4 OIL COOLER HOSE
| *a | Paint Mark |
| *b | 0 to 3.0 mm (0 to 0.118 in.) |
| *c | 2.0 to 7.0 mm (0.0788 to 0.275 in.) |
Install the inlet No. 4 oil cooler hose, and slide the 4 hose clips to secure the hose as shown in the illustration.
Make sure the pinching portion of each hose clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.
32942
5.INSTALL INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE
| *a | 0 to 3.0 mm (0 to 0.118 in.) |
| *b | 2.0 to 7.0 mm (0.0788 to 0.275 in.) |
Install the inlet No. 2 oil cooler hose and inlet No. 3 oil cooler hose, and slide the 4 hose clips to secure the hose as shown in the illustration.
Make sure the pinching portion of each hose clip is facing the direction shown in the illustration.
32942
6.INSTALL INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE
| *a | Paint Mark |
| *b | 0 to 3.0 mm (0 to 0.118 in.) |
| *c | 2.0 to 7.0 mm (0.0788 to 0.275 in.) |
Install the inlet No. 1 oil cooler hose and outlet No. 1 oil cooler hose, and slide the 4 hose clips to secure the hose as shown in the illustration.
Make sure the pinching portion of each hose clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.
Attach the hose to the flexible hose clamp and close the clamp as shown in the illustration.
32943B
7.INSTALL TRANSMISSION OIL COOLER HOSE
| *a | RH Side |
| *b | Paint Mark |
Install the 2 transmission oil cooler hoses, and slide the 4 hose clips to secure the hose as shown in the illustration.
Make sure the pinching portion of each hose clip is facing the direction shown in the illustration.
Make sure the paint mark of each hose is facing outward.
8.ADD AUTOMATIC TRANSMISSION FLUID
52521
9.INSTALL FRONT UPPER CENTER BUMPER RETAINER
53784
10.INSTALL FRONT FENDER APRON TRIM PACKING C
53782
11.INSTALL FRONT FENDER APRON TRIM PACKING A
51442
12.INSTALL NO. 2 ENGINE UNDER COVER
51405A
13.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
53806
14.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
15.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH