1.REMOVE ENGINE WIRE
Engine LH Side:
Disconnect the 2 camshaft timing control valve connectors.
Disconnect the 4 ignition coil connectors.
Disconnect the 2 VVT sensor connectors.
Disconnect the camshaft position sensor connector.
Disconnect the vacuum switching valve connector (for ACIS).
Disconnect the purge VSV connector.
Disconnect the engine coolant temperature sensor connector.
Disconnect the fuel injector connector.
Disconnect the noise filter connector.
Remove the bolt and disconnect the 7 clamps.
Engine RH Side:
Disconnect the 2 camshaft timing control valve connectors.
Disconnect the 4 ignition coil connectors.
Disconnect the 2 VVT sensor connectors.
Disconnect the fuel injector connector.
Disconnect the noise filter connector.
Disconnect the throttle sensor connector.
Disconnect the oil pressure sender gauge connector.
Disconnect the oil level sensor connector.
Disconnect the 9 clamps.
Engine Rear Side:
w/ Secondary Air Injection System:
Disconnect the 2 air switching valve connectors.
| *A | w/ Secondary Air Injection System |
| *B | w/o Secondary Air Injection System |
Disconnect the sensor wire connector.
Disconnect the 5 clamps.
Remove the 3 bolts.
Remove the engine wire.
12601B
2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
12613
3.REMOVE NO. 3 ENGINE COVER
23271H
4.REMOVE NO. 1 FUEL HOSE
23902
5.DISCONNECT NO. 2 FUEL TUBE
23901
6.DISCONNECT NO. 1 FUEL TUBE
23808
7.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY LH
23807
8.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY RH
23250
9.REMOVE FUEL INJECTOR ASSEMBLY
17111
10.REMOVE INTAKE MANIFOLD
Disconnect the ventilation hose from the ventilation pipe of the cylinder head cover LH and RH.
Disconnect the 2 water by-pass hoses.
Disconnect the No. 1 ventilation hose.
Remove the bolt and wire bracket from the intake manifold.
Remove the 2 nuts, 8 bolts, intake manifold and 2 gaskets.
23902
11.REMOVE NO. 2 FUEL TUBE
Remove the 2 bolts and No. 2 fuel tube.
23901
12.REMOVE NO. 1 FUEL TUBE
11212
13.REMOVE NO. 2 ENGINE COVER
12611
14.REMOVE NO. 1 ENGINE COVER
16207
15.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
16261G
16.REMOVE NO. 1 WATER BY-PASS HOSE
16355
17.REMOVE FRONT WATER BY-PASS JOINT
17303
18.REMOVE AIR PIPE SUB-ASSEMBLY (w/ Secondary Air Injection System)
Remove the 2 bolts, air pipe and 2 No. 1 air hoses.
16323
19.REMOVE WATER INLET HOUSING
16206
20.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 2 bolts and water by-pass pipe.
25720
21.REMOVE AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)
17362
22.REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)
17363Q
23.REMOVE NO. 3 AIR TUBE (w/ Secondary Air Injection System)
82219A
24.REMOVE SENSOR WIRE
Disconnect the 4 knock sensor connectors.
Disconnect the 3 clamps. Then remove the sensor wire.
12215
25.REMOVE SEPARATOR CASE
Remove the 4 bolts and separator case.
89615
26.REMOVE KNOCK SENSOR
Remove the 4 bolts and 4 knock sensors.
11415
27.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY
Remove the 2 water drain cock plugs from the water drain cocks.
Remove the 2 water drain cocks from the cylinder block.
| *A | RH |
| *B | LH |
12311
28.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH
Remove the 4 bolts and mounting bracket.
12315
29.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
Remove the 4 bolts and mounting bracket.
19500
30.REMOVE IGNITION COIL ASSEMBLY
Remove the 8 bolts and 8 ignition coils.
86011A
31.REMOVE NOISE FILTER
Remove the 2 bolts and 2 noise filters from the cylinder head cover.