1.DISCHARGE FUEL SYSTEM PRESSURE
2. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
52119A
4.REMOVE FRONT BUMPER COVER
for Standard (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(for Standard)>REMOVAL)
w/ Winch (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/ Winch)>REMOVAL)
32917
5.REMOVE TRANSMISSION OIL COOLER AIR DUCT
53294C
6.REMOVE RADIATOR SIDE DEFLECTOR LH
55781E
7.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53737B
8.REMOVE FRONT FENDER APRON SEAL LH
53736G
9.REMOVE FRONT FENDER APRON SEAL FRONT RH
51405C
10.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
51442
11.REMOVE NO. 2 ENGINE UNDER COVER
12.DRAIN ENGINE OIL
13.DRAIN ENGINE COOLANT
11209
14.REMOVE V-BANK COVER SUB-ASSEMBLY
17880
15.REMOVE AIR CLEANER HOSE ASSEMBLY
17700
16.REMOVE AIR CLEANER ASSEMBLY
16400
17.REMOVE RADIATOR ASSEMBLY
18.DISCONNECT ENGINE WIRE
Engine Room LH Side:
Remove the engine room relay block cover.
Disconnect the 2 connectors and 2 clips from the engine room junction block.
w/ Secondary Air Injection System:
Disconnect the 4 air injection control driver connectors and wire harness clamp.
Disconnect the injector connector.
Disconnect the 4 ignition coil connectors.
Disconnect the 2 VVT sensor connectors.
Disconnect the 4 clamps.
Remove the bolt and disconnect the ground wire.
Disconnect the noise filter connector.
Disconnect the engine coolant temperature sensor connector.
Disconnect the 2 camshaft timing oil control valve connectors.
Disconnect the camshaft position sensor connector.
Disconnect the 3 clamps.
Disconnect the cooler compressor connector.
Engine Room RH Side:
Disconnect the 2 camshaft timing oil control valve connectors.
Disconnect the 4 ignition coil connectors.
Disconnect the injector connector.
Disconnect the 2 VVT sensor connectors.
Disconnect the noise filter connector.
Remove the bolt and disconnect the ground wire.
w/ Secondary Air Injection System:
Disconnect the 2 air pump connectors and clamp.
| *a | Clamp |
|
Connector |
Disconnect the throttle position sensor and throttle control motor connector.
Disconnect the 6 clamps.
Disconnect the 2 clamps and power steering oil pressure switch connector.
19.DISCONNECT AIR PUMP HOSE AND WIRE HARNESS (w/ Secondary Air Injection System)
Disconnect the No. 2 and No. 3 air hoses.
| *1 | No. 2 Air Hose |
| *2 | No. 3 Air Hose |
Disconnect the 2 clamps.
20.DISCONNECT WATER PIPE AND HOSE SUB-ASSEMBLY
Disconnect the 3 hoses.
Remove the 2 bolts and disconnect the water pipe and hose from the cylinder head cover.
88320
21.DISCONNECT COOLER COMPRESSOR ASSEMBLY
Remove the 3 bolts, nut and stud bolt, and disconnect the cooler compressor.
It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.
23902
22.DISCONNECT NO. 2 FUEL TUBE SUB-ASSEMBLY
Remove the 2 bolts and disconnect the fuel tube.
| *A | LH Side |
| *B | RH Side |
23.REMOVE OIL FILTER ELEMENT
11452
24.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
83520
25.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY
16207
26.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 3 bolts.
Disconnect the 4 hoses and remove the water by-pass pipe.
15781
27.REMOVE NO. 1 OIL COOLER BRACKET
15671
28.REMOVE OIL FILTER BRACKET
17111
29.REMOVE INTAKE MANIFOLD
44310
30.DISCONNECT VANE PUMP ASSEMBLY
Remove the 2 bolts and disconnect the vane pump.
32907A
31.DISCONNECT OIL COOLER PIPE ASSEMBLY
27020
32.REMOVE GENERATOR ASSEMBLY
16261G
33.REMOVE NO. 1 WATER BY-PASS HOSE
Remove the No. 1 water by-pass hose by disconnecting the hose from the water inlet housing and front water by-pass joint.
16206
34.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
w/ Secondary Air Injection System:
Remove the bolt and disconnect the air tube.
Disconnect the 2 hoses.
Remove the 2 bolts and water by-pass pipe.
16355
35.REMOVE FRONT WATER BY-PASS JOINT
Disconnect the No. 2 water by-pass hose from the water by-pass joint.
Remove the 4 nuts, water by-pass joint and 2 gaskets.
11212
36.REMOVE NO. 2 ENGINE COVER
12611
37.REMOVE NO. 1 ENGINE COVER
17303
38.REMOVE AIR PIPE SUB-ASSEMBLY (w/ Secondary Air Injection System)
Remove the bolt, disconnect the 2 hoses, and remove the air pipe.
16323
39.REMOVE WATER INLET HOUSING
Remove the 3 bolts, water inlet housing and gasket.
16173
40.REMOVE WATER PUMP PULLEY
Using SST, hold the water pump pulley.
Remove the 4 bolts and water pump pulley.
16603
41.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
Remove the bolt and idler pulley.
16211
42.REMOVE FLUID COUPLING BRACKET
Remove the 4 bolts and fluid coupling bracket.
16620
43.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
Remove the standard bolt, 6 mm hexagon wrench bolt and belt tensioner.
19500
44.REMOVE IGNITION COIL ASSEMBLY
Remove the 8 bolts and 8 ignition coils.
11202
45.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
Remove the 14 bolts, seal washer, cylinder head cover and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).
11201
46.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH
Remove the bolt and noise filter.
Remove the 14 bolts, seal washer, cylinder head cover and gasket.
Make sure the removed parts are returned to the same places they were removed from.
Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).
11193
47.REMOVE SPARK PLUG TUBE GASKET
13471
48.REMOVE CRANKSHAFT PULLEY
Using SST, loosen the crankshaft pulley set bolt until 2 or 3 threads are engaged.
| *a | Hold |
|
Turn |
Using the pulley set bolt and SST, remove the crankshaft pulley.
| *a | Hold |
|
Turn |
49.DISCONNECT WIRE HARNESS CLAMP BRACKET
Remove the bolt and disconnect the bracket.
13521A
50.REMOVE CRANKSHAFT TIMING GEAR KEY
Using a screwdriver, remove the timing gear key from the crankshaft.
11302
51.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
Remove the 28 bolts and nut shown in the illustration.
|
Bolt |
|
Nut |
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver as shown in the illustration.
Be careful not to damage the contact surfaces of the cylinder head, cylinder block and chain cover.
Tape the screwdriver tip before use.
Remove the oil pump gasket from the cylinder block.
Remove the O-ring from the oil pan.
16322
52.REMOVE WATER INLET PIPE
Remove the water inlet pipe.
Remove the 2 O-rings from the water inlet pipe.