Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The Mass Air Flow (MAF) meter is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.

Inside the MAF meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to these components in the MAF meter. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and the cold film element create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. Fail-safe mode continues until a pass condition is detected.


A160257E01
2.954,2.753 5.064,2.960 2.110,0.207 10 Temperature Sensor (Thermistor) 1.929,0.681 2.184,0.845 0.255,0.163 10 +B 1.878,1.033 2.969,1.179 1.091,0.145 10 Power Transistor 2.18,1.424 3.342,1.595 1.162,0.171 10 Hot Wire (Heater) 5.974,2.76 7.117,2.932 1.143,0.171 10 Hot Wire (Heater) 1.357,2.631 1.593,1.889 false 2.142,1.492 1.962,1.924 false 2.574,2.013 3.560,2.207 0.986,0.194 10 Output Voltage 4.646,2.733 5.424,1.969 false 6.322,2.003 6.116,2.746 false 1.323,1.911 1.487,2.075 0.164,0.165 10 A 2.133,1.904 2.299,2.072 0.165,0.168 10 B 4.967,3.273 6.151,3.439 1.184,0.165 10 Cold Film Element 0.474,2.638 1.658,2.803 1.184,0.165 10 Cold Film Element 5.507,3.235 5.794,1.968 false

DTC Code DTC Detection Condition Trouble Area
P0102 The Mass Air Flow (MAF) meter voltage is below 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in Mass Air Flow (MAF) meter circuit

·

MAF meter

·

ECM


P0103 The MAF meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in MAF meter circuit

·

MAF meter

·

ECM



HINT:

When any of these DTCs is output, check the air-flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Mass Air Flow Rate (gm/s) Malfunction
Approximately 0.0
·

Open in Mass Air Flow (MAF) meter power source circuit

·

Open or short in VG circuit


160.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the MAF meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the MAF meter and stores DTC(s).

Example:

When the sensor output voltage remains at below 0.2 V, or higher than 4.9 V for more than 3 seconds, the ECM stores DTC(s).

If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

WIRING DIAGRAM

A344921E11
1.74,1.906 3.344,2.646 1.604,0.74 10 false No. 2 Integration Relay 0.469,2.635 1.24,2.833 0.771,0.198 10 false P/I-B 0.656,3.938 1.271,4.135 0.615,0.198 10 false Battery 6.375,3.604 6.865,3.958 0.49,0.354 10 false ECM 4.01,1.979 5.354,2.448 1.344,0.469 10 false Mass Air Flow Meter 2.5,0.75 3.729,0.948 1.229,0.198 10 false EFI NO. 2 1.604,1.521 3.063,1.698 1.458,0.177 10 false EFI MAIN NO. 1 1.115,0.76 1.76,1.125 0.646,0.365 10 false EFI MAIN NO. 1 6.146,3.052 6.76,3.25 0.615,0.198 10 false MREL 6.135,1.385 6.75,1.583 0.615,0.198 10 false E2G 6.146,0.833 6.49,1.083 0.344,0.25 10 false VG 5.823,0.906 6.167,1.156 0.344,0.25 10 false C45 5.813,1.427 6.156,1.677 0.344,0.25 10 false C45 5.823,3.052 6.167,3.302 0.344,0.25 10 false A38 3.208,0.594 3.552,0.844 0.344,0.25 10 false 1S 3.208,1.146 3.552,1.396 0.344,0.25 10 false 1S 0.771,0.604 1.115,0.854 0.344,0.25 10 false 1X 1.167,1.646 1.51,1.896 0.344,0.25 10 false 1S 4.01,1.823 4.354,2.073 0.344,0.25 10 false C50 5.021,0.823 5.365,1.073 0.344,0.25 10 false VG 4.958,1.385 5.573,1.583 0.615,0.198 10 false E2G 5.875,1.26 6.271,1.458 0.396,0.198 10 false 70 5.865,0.75 6.323,0.948 0.458,0.198 10 false 68 5.854,2.875 6.313,3.073 0.458,0.198 10 false 6 5.323,0.823 5.594,0.979 0.271,0.156 10 false 3 4.094,0.51 4.552,0.708 0.458,0.198 10 false +B 5.313,1.396 5.583,1.552 0.271,0.156 10 false 2 3.927,0.51 4.198,0.667 0.271,0.156 10 false 1 3.25,0.438 3.521,0.594 0.271,0.156 10 false 1 3.25,0.969 3.521,1.125 0.271,0.156 10 false 8 0.813,0.438 1.083,0.594 0.271,0.156 10 false 1 1,1.656 1.271,1.813 0.271,0.156 10 false 4

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.


e.

Read the values displayed on the tester.

Result
Mass Air Flow Rate (gm/s) Proceed to
0.0 A
271.0 or more B
Between 1.0 and 270.0* C

HINT:

*: The value must change when the throttle valve is open or closed with the engine running.




A

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)

B

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

C

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
U162846E01
0.083,0.091 2.434,0.455 2.350,0.364 10 Front view of wire harness connector: (to MAF Meter) 0.999,2.69 1.411,2.828 0.413,0.139 10 +B (+) 1.364,2.033 1.264,2.69 false 0.398,1.915 0.678,2.054 0.281,0.139 10 C50

a.

Disconnect the C50 Mass Air Flow (MAF) meter connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C50-1 (+B) - Body ground Engine switch on (IG) 11 to 14 V




OK

3.INSPECT MASS AIR FLOW METER

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO.2 INTEGRATION RELAY)
3.INSPECT MASS AIR FLOW METER

OK

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

4.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the C50 MAF meter connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-3 (VG) - C45-68 (VG) Always Below 1 Ω
C50-2 (E2G) - C45-70 (E2G) Always Below 1 Ω
C50-3 (VG) or C45-68 (VG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO.2 INTEGRATION RELAY)
a.

Disconnect the C50 MAF meter connector.


b.

Remove the No. 2 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-1 (+B) - 1S-1 Always Below 1 Ω
C50-1 (+B) or 1S-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the C50 MAF meter connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-3 (VG) - C45-68 (VG) Always Below 1 Ω
C50-2 (E2G) - C45-70 (E2G) Always Below 1 Ω
C50-3 (VG) or C45-68 (VG) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
U162847E02
1.615,2.073 2.01,2.729 true 0.156,0.125 2.521,0.5 2.365,0.375 10 false Front view of wire harness connector: (to MAF Meter) 1.927,2.76 2.24,2.927 0.313,0.167 10 false E2G 0.417,1.917 0.719,2.104 0.302,0.188 10 false C50

a.

Disconnect the C50 MAF meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-2 (E2G) - Body ground Always Below 1 Ω




OK

NG