Refer to DTC P0412 (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>SFI SYSTEM(w/ Secondary Air Injection System)>P0412).
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P1613
P1614 |
Either of the following conditions (1) or (2) is met:
(1) All of the following conditions are met (1 trip detection logic): ·
Either the air pump or the air switching valve is not operating. ·
The diagnostic signal from the Air Injection Control Driver (AID) is 80%. ·
The battery voltage is 8 V or higher. (2) Both of the following conditions are met (1 trip detection logic): ·
The battery voltage is 8 V or higher. ·
The diagnostic signal from the AID is abnormal (duty signal other than 0, 20, 40, 80 and 100%). |
·
Air Injection Control Driver (AID) ·
Open in AID ground circuit |
| P1613
P1614 |
All of the following conditions are met (1 trip detection logic): (a)
The air injection system is operating (Air Switching Valve [ASV] ON and air pump ON). (b)
The diagnostic signal from the Air Injection Control Driver (AID) is 0%. (c)
The battery voltage is 8 V or higher. |
·
Short in diagnostic information signal circuit (AID - ECM) ·
Open or short in air pump and air switching valve command signal circuit (AID - ECM) ·
Open in AID ground circuit ·
AID ·
ECM |
| P1613
P1614 |
Both of the following conditions are met (1 trip detection logic): (a)
The battery voltage is 8 V or higher. (b)
The diagnostic signal from the Air Injection Control Driver (AID) is 100%. |
·
Open or short in AID +B circuit ·
Open in diagnostic information signal circuit (AID - ECM) ·
AID ·
ECM |
For a short time after a cold engine start, the ECM transmits command signals to the Air Injection Control Driver (AID) to drive the air pump and the Air Switching Valve (ASV). The AID detects open and short circuits according to the voltages at the AID terminals to the air pump and ASV, and the circuit voltage of the AID power source, and transmits diagnostic information as a signal to the ECM.
If the Secondary Air Injection (AIR) system circuit or the AID itself malfunctions, the AID sends a malfunction signal (duty signal) as diagnostic information to the ECM (when the system is normal, a system normal signal is sent). The ECM stores the DTC based on the diagnostic information from the AID.
EXAMPLE:
The duty ratio of the diagnostic signal from the AID is 0 or 100% (remains at 0 V or the same as battery voltage).
The duty ratio of the diagnostic signal from the AID shows an impossible ratio (other than 0, 20, 40, 80 and 100%).
The AID outputs the normal signal (normal duty signal: 80%) while the system is not operating.
Refer to DTC P0412 (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>SFI SYSTEM(w/ Secondary Air Injection System)>P0412).
By using the intelligent tester to perform the Secondary Air Injection Check operation in the Utility, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
|---|---|
| P1613 and/or P1614 are output | A |
| P1613 and/or P1614 and other DTCs are output | B |
If any DTCs other than P1613 and P1614 are output, troubleshoot those DTCs first.
A
B
Disconnect the Air Injection Control Driver (AID) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C174-5 (+B) - Body ground | Engine switch on (IG) | 11 to 14 V (near battery voltage) |
| C176-5 (+B2) - Body ground | Engine switch on (IG) | 11 to 14 V (near battery voltage) |
OK
NG
Disconnect the ECM connector.
Disconnect the AID connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C45-63 (AIRP) - C174-4 (SIP) | Always | Below 1 Ω |
| C45-61 (AIRV) - C174-3 (SIV) | Always | Below 1 Ω |
| C45-62 (ARP2) - C176-4 (SIP2) | Always | Below 1 Ω |
| C45-60 (ARV2) - C176-3 (SIV2) | Always | Below 1 Ω |
| C45-52 (AIDI) - C174-2 (DI) | Always | Below 1 Ω |
| C45-51 (AID2) - C176-2 (DI2) | Always | Below 1 Ω |
| C174-1 (E) - Body ground | Always | Below 1 Ω |
| C176-1 (E2) - Body ground | Always | Below 1 Ω |
| C45-63 (AIRP) or C174-4 (SIP) - Body ground | Always | 10 kΩ or higher |
| C45-61 (AIRV) or C174-3 (SIV) - Body ground | Always | 10 kΩ or higher |
| C45-62 (ARP2) or C176-4 (SIP2) - Body ground | Always | 10 kΩ or higher |
| C45-60 (ARV2) or C176-3 (SIV2) - Body ground | Always | 10 kΩ or higher |
| C45-52 (AIDI) or C174-2 (DI) - Body ground | Always | 10 kΩ or higher |
| C45-51 (AID2) or C176-2 (DI2) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the AID connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C174-2 (DI) - C174-1 (E) | Engine switch on (IG) | 11 to 14 V (near battery voltage) |
| C176-2 (DI2) - C176-1 (E2) | Engine switch on (IG) | 11 to 14 V (near battery voltage) |
OK
NG
Disconnect the AID connectors.
Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.
When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
Turn the engine switch off.
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.
Turn the engine switch off when the Secondary Air Injection Check operation finishes.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C174-3 (SIV) - C174-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| C176-3 (SIV2) - C176-1 (E2) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| C174-3 (SIV) - C174-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| C176-3 (SIV2) - C176-1 (E2) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN or AIR PUMP 2: ON, ASV 2: OPEN.
When Manual Mode is selected, the intelligent tester initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
Turn the engine switch off.
Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.
Turn the engine switch off when the Secondary Air Injection Check operation finishes.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C174-4 (SIP) - C174-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| C176-4 (SIP2) - C176-1 (E2) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| C174-4 (SIP) - C174-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| C176-4 (SIP2) - C176-1 (E2) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
OK
NG
Replace the air injection control driver (See page Engine / Hybrid System>3UR-FE (EMISSION CONTROL)>AIR INJECTION DRIVER (w/ Secondary Air Injection System)>REMOVAL).
NEXT
Start the engine and warm it up.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the tester initialization is finished.
Perform the Automatic Mode operation by pressing Next.
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
|---|---|
| No DTC is output | A |
| Other DTCs are output | B |
Turn the engine switch off.
When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.
Turn the engine switch off when the Secondary Air Injection Check operation finishes.
A
B