Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/ Secondary Air Injection System) › from 2017.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0327320 SFI SYSTEM(w/ Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P2431  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1  P2432  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1  P2433  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1  P2436  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank 2  P2437  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank 2  P2438  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank 2  


DESCRIPTION

The Secondary Air injection (AIR) system consists of an air pump, the Air Switching Valve (ASV), a pressure sensor, the Air Injection Control Driver (AID) and the ECM. For a short time after a cold engine start, the AIR system pumps secondary air to the exhaust port of the cylinder head to purify the exhaust emissions. The secondary air is supplied by the air pump and is pumped to the exhaust port through the ASV.

The AID drives the ASV and the air pump according to command signals transmitted by the ECM. The pressure sensor detects the pressure in the secondary air passage when the AIR system is ON and OFF, and transmits a pressure signal to the ECM.

The AID is not only equipped to drive the pump and valve, but also with a diagnosis function to detect malfunctions in the AIR system circuit.

HINT:

As a large current is required to drive the air pump and ASV, an AID is installed to this system.


A162565E06
0.781,1.844 0.49,2.438 false 3.979,0.531 3.458,1.177 false 3.563,3.26 3.469,2.583 true 2.479,2.563 2.635,1.99 false 3.521,2.344 4.677,3.604 true 5.406,1.438 5.146,1.708 false 3.448,1.948 4.188,1.031 false 1.927,1.594 3.052,0.104 false 1.354,0.573 1.708,0.74 0.354,0.167 10 false ECM 3.115,0.031 5.135,0.24 2.021,0.208 10 false Air Injection Control Driver (AID) 0.125,2.458 1.302,2.656 1.177,0.198 10 false Diagnostic Signal 4.031,0.448 5.083,0.635 1.052,0.188 10 false Pressure Signal 3.313,3.292 4.083,3.469 0.771,0.177 10 false Reed Valve 1.927,2.563 3.042,2.75 1.115,0.188 10 false ASV Drive Signal 4.198,3.635 5.417,4 1.219,0.365 10 false Air Switching Valve (ASV) 5.75,3.427 6.365,3.625 0.615,0.198 10 false Air Pump 6.271,2.021 6.635,2.208 0.365,0.188 10 false Filter 5.448,1.292 6.875,1.49 1.427,0.198 10 false Air Pump Drive Signal 4.24,0.917 5.365,1.125 1.125,0.208 10 false Pressure Sensor

DTC Code DTC Detection Condition Trouble Area
P2431
P2436
The pressure sensor indicates below 45.6 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) (2 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


P2432
P2437
While the engine is running, the voltage output of the pressure sensor remains below 0.5 V (1 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


P2433
P2438
While the engine is running, the voltage output of the pressure sensor remains higher than 4.5 V (1 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM



MONITOR DESCRIPTION

A085160E41
0.073,0.063 1.948,0.427 1.875,0.365 12 false Reference (for Bank 1): 2.677,2.969 3.104,3.167 0.427,0.198 10 false ECM 2.302,0.896 2.823,1.104 0.521,0.208 10 false VCAI 2.302,1.5 2.583,1.677 0.281,0.177 10 false AIP 0.833,1.615 1.125,1.792 0.292,0.177 10 false AIP 2.281,2.146 2.729,2.323 0.448,0.177 10 false EAIP 0.865,0.99 1.156,1.156 0.292,0.167 10 false VC 0.875,2.25 1.177,2.438 0.302,0.188 10 false E2 0.219,2.792 1.667,3.063 1.448,0.271 10 false Pressure Sensor

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the air switching valve in the secondary air injection system.

If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range, the ECM interprets this deviation as a malfunction in the pressure sensor or circuit and stores DTC(s).

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - ECM)
a.

Disconnect the pressure sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C137-3 (AIP) - C45-73 (AIP) Always Below 1 Ω
C137-2 (VC) - C45-75 (VCAI) Always Below 1 Ω
C137-4 (E2) - C45-74 (EAIP) Always Below 1 Ω
C138-3 (AIP2) - C45-72 (AIP2) Always Below 1 Ω
C138-2 (VC2) - C45-75 (VCAI) Always Below 1 Ω
C138-4 (E22) - C45-74 (EAIP) Always Below 1 Ω
C137-3 (AIP) or C45-73 (AIP) - Body ground Always 10 kΩ or higher
C137-2 (VC) or C45-75 (VCAI) - Body ground Always 10 kΩ or higher
C138-3 (AIP2) or C45-72 (AIP2) - Body ground Always 10 kΩ or higher
C138-2 (VC2) or C45-75 (VCAI) - Body ground Always 10 kΩ or higher




OK

2.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR)
A158647E11
1.073,0.771 1.74,0.177 1.74,0.177 1.094,2.313 true 1.792,0.052 2.885,0.406 1.094,0.354 10 true Pressure Gauge 0.063,0.052 0.979,0.26 0.917,0.208 12 true for Bank 1: 0.063,1.771 0.969,2 0.906,0.229 12 true for Bank 2:

a.

Connect a pressure gauge to the air pressure sensor as shown in the illustration.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the engine switch on (IG) and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (Absolute) and Air Pump2 Pressure (Absolute).


e.

Check that the pressure displayed on the tester fluctuates when applying the pressure to the pressure sensor with the pressure gauge.

OK:

Pressure fluctuates in response to pressure applied with pressure gauge.


HINT:

The tester displays the air pump pressure as absolute pressure.




OK

NG