Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2017.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0746  Pressure Control Solenoid "A" Performance or Stuck OFF  


DESCRIPTION

Based on signals from the transmission revolution sensors (NT and SP2), the actual gear is detected.

If the detected gear is different than the commanded gear, the TCM detects related mechanical problems in the shift solenoid valves, transmission valve body assembly and automatic transmission assembly (clutch, brake, gear, etc.).

HINT:

Actual gear when a problem occurs in shift solenoid valve SL1 (without fail-safe control):

TCM commanded gear 1st 2nd 3rd 4th 5th 6th 7th 8th
Actual gear during SL1 stuck ON malfunction 1st 2nd 3rd 4th 5th 6th 7th 8th
Actual gear during SL1 stuck OFF malfunction N* N* N* N* N* 6th 7th 8th

*: Neutral



DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0746 SL1 stuck ON malfunction:
1.

Battery voltage is 9.5 V or higher, engine speed is more than 400 rpm, and the vehicle is driven with the shift lever in D (no malfunctions are detected in shift solenoid valve SC1, SC2, SL1, SL2, SL3, SL4, SL5, SLT, SLU, park/neutral position switch assembly, TCM, electronic throttle, knock control sensor, No. 1 ATF temperature sensor, transmission revolution sensors (NT), and CAN communication system)

2.

The gear commanded by the TCM is the same as the actual gear

3.

Malfunction status is detected 4 times per trip

4.

2 trip detection logic


·

Shift solenoid valve SC1

·

Shift solenoid valve SL1

·

Transmission valve body assembly

·

Automatic transmission assembly (clutch, brake, gear, etc.)


SL1 stuck OFF malfunction:
1.

Battery voltage is 9.5 V or higher, engine speed is more than 400 rpm, and the vehicle is driven with the shift lever in D (no malfunctions are detected in shift solenoid valve SC1, SC2, SL1, SL2, SL3, SL4, SL5, SLT, SLU, park/neutral position switch assembly, TCM, electronic throttle, knock control sensor, No. 1 ATF temperature sensor, transmission revolution sensors (NT), and CAN communication system)

2.

When the TCM commands the transmission to shift to 1st to 5th, the engine overruns (neutral status).

3.

Malfunction status is detected 5 times per trip

4.

2 trip detection logic


·

Shift solenoid valve SL1

·

Shift solenoid valve SL2

·

Shift solenoid valve SL3

·

Shift solenoid valve SL4

·

Shift solenoid valve SL5

·

Shift solenoid valve SLT

·

Transmission valve body assembly

·

Automatic transmission assembly (clutch, brake, gear, etc.)



MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft speed and output shaft speed, the TCM detects the actual gear (1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear position). When the gear commanded by the TCM and the actual gear are not the same, the TCM illuminates the MIL* and stores this DTC.

*: w/ OBD


CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Perform the D Position Shift Test in Road Test (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST).*1

2.

Turn the engine switch off.

3.

Perform step (*1) again.



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0746)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.


e.

Read the DTCs using the GTS.

Result
Result Proceed to
DTC P0746 and DTC P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and/or P2817 are output A
Only DTC P0746 is output B
DTCs other than P0746, P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and P2817 are also output C

HINT:

If DTCs other than P0746, P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and P2817 are output, perform troubleshooting for those DTCs first.




A

2.CLEAR DTC AND PERFORM STALL SPEED TEST

B

3.INSPECT SHIFT SOLENOID VALVE SL1, SL2, SL3, SL4 AND SL5

C

2.CLEAR DTC AND PERFORM STALL SPEED TEST
a.

Clear the DTCs (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).

HINT:

Write down the currently output DTCs before clearing them.



b.

Perform the stall speed test (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>MECHANICAL SYSTEM TESTS).

Result
Test Condition Proceed to
Stall speed test can be performed A
Stall speed test cannot be performed B



A

3.INSPECT SHIFT SOLENOID VALVE SL1, SL2, SL3, SL4 AND SL5

B

5.INSPECT SHIFT SOLENOID VALVE SLT
3.INSPECT SHIFT SOLENOID VALVE SL1, SL2, SL3, SL4 AND SL5
a.
C209928E13
0.057,0.005 0.374,0.207 0.317,0.202 10 *a 1.757,0.949 2.207,0.361 false 2.238,0.194 2.402,0.396 0.164,0.202 10 1 1.506,0.949 1.056,0.361 false 0.918,0.194 1.082,0.396 0.164,0.202 10 2 1.757,2.945 2.207,2.358 false 2.238,2.191 2.402,2.393 0.164,0.202 10 1 1.506,2.945 1.056,2.358 false 0.918,2.191 1.082,2.393 0.164,0.202 10 2 1.923,3.928 2.122,4.130 0.200,0.202 10 (-) 1.119,3.928 1.339,4.130 0.221,0.202 10 (+)

Remove the shift solenoid valve SL1, SL2, SL3, SL4 and SL5 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 1 of the shift solenoid valve SL1 - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Terminal 1 of the shift solenoid valve SL2 - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Terminal 1 of the shift solenoid valve SL3 - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Terminal 1 of the shift solenoid valve SL4 - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Terminal 1 of the shift solenoid valve SL5 - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Text in Illustration
*1 Shift Solenoid Valve SL1, SL2, SL3, SL4 and SL5


OK

4.INSPECT SHIFT SOLENOID VALVE SC1

NG

REPLACE SHIFT SOLENOID VALVE SL1, SL2, SL3, SL4 OR SL5

4.INSPECT SHIFT SOLENOID VALVE SC1
a.
C342509E01
0.122,0.053 0.425,0.245 0.303,0.192 10 *1 2.873,0.032 3.175,0.223 0.303,0.192 10 (+) 2.054,0.032 2.357,0.223 0.303,0.192 10 (-)

Remove the shift solenoid valve SC1 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SC1 connector - Shift solenoid valve SC1 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve SC1 connector

·

Battery negative (-) → Shift solenoid valve SC1 body


Valve moves and makes an operating noise



Text in Illustration
*1 Shift Solenoid Valve SC1


OK

5.INSPECT SHIFT SOLENOID VALVE SLT

NG

5.INSPECT SHIFT SOLENOID VALVE SLT
a.
C209928E13
0.057,0.005 0.374,0.207 0.317,0.202 10 *a 1.757,0.949 2.207,0.361 false 2.238,0.194 2.402,0.396 0.164,0.202 10 1 1.506,0.949 1.056,0.361 false 0.918,0.194 1.082,0.396 0.164,0.202 10 2 1.757,2.945 2.207,2.358 false 2.238,2.191 2.402,2.393 0.164,0.202 10 1 1.506,2.945 1.056,2.358 false 0.918,2.191 1.082,2.393 0.164,0.202 10 2 1.923,3.928 2.122,4.130 0.200,0.202 10 (-) 1.119,3.928 1.339,4.130 0.221,0.202 10 (+)

Remove the shift solenoid valve SLT (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 1 of the shift solenoid valve SLT - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Text in Illustration
*1 Shift Solenoid Valve SLT


OK

6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL).

OK:

There is no foreign matter on each valve and they operate smoothly.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY