Based on signals from the transmission revolution sensors (NT and SP2), the actual gear is detected.
If the detected gear is different than the commanded gear, the TCM detects related mechanical problems in the shift solenoid valves, transmission valve body assembly and automatic transmission assembly (clutch, brake, gear, etc.).
Actual gear when a malfunction occurs in shift solenoid valve SC1 (without fail-safe control):
| TCM commanded gear | 1st | 2nd | 3rd | 4th | 5th | 6th | 7th | 8th |
| Actual gear during SC1 stuck OFF malfunction | 1st | 2nd | 3rd | 4th | 5th | 4th or 6th | 3rd or 7th | 2nd or 8th |
| DTC No. | DTC Detection Condition
1.
Diagnosis Condition 2.
Malfunction Status 3.
Malfunction Time 4.
Other |
Trouble Area |
|---|---|---|
| P076B | 1.
Battery voltage is 9.5 V or higher, engine speed is more than 400 rpm, and the vehicle is driven with the shift lever in D (no malfunctions are detected in shift solenoid valve SC1, SC2, SL1, SL2, SL3, SL4, SL5, SLT, SLU, park/neutral position switch assembly, TCM, electronic throttle, knock control sensor, No. 1 ATF temperature sensor, transmission revolution sensors (NT), and CAN communication system) 2.
One of the following occurs: (a) When gear shifts to 6th are requested by TCM, actual gear changes to 4th gear. (b) When gear shifts to 7th are requested by TCM, actual gear changes to 3rd gear. (c) When gear shifts to 8th are requested by TCM, actual gear changes to 2nd gear. 3.
Malfunction status is detected 5 times per trip 4.
2 trip detection logic |
·
Shift solenoid valve SC1 ·
Shift solenoid valve SL1 ·
Transmission valve body assembly ·
Automatic transmission assembly (clutch, brake, gear, etc.) |
This DTC indicates a "stuck OFF" malfunction of shift solenoid valve SC1.
The TCM commands gear shifts by turning the shift solenoid valves on or off. When the gear position commanded by the TCM and the actual gear position are not the same, the TCM illuminates the MIL* and stores the DTC.
*: w/ OBD
Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform the D Position Shift Test in Road Test (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST).*1
Turn the engine switch off.
Perform step (*1) again.
Check for DTCs again (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P076B and DTC P0746, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and/or P2817 are output | A |
| Only DTC P076B is output | |
| DTCs other than P0746, P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and P2817 are also output | B |
If DTCs other than P0746, P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and P2817 are output, perform troubleshooting for those DTCs first.
A
B
Remove the shift solenoid valve SC1 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve SC1 connector - Shift solenoid valve SC1 body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) → Shift solenoid valve SC1 connector ·
Battery negative (-) → Shift solenoid valve SC1 body |
Valve moves and makes an operating noise |
| *1 | Shift Solenoid Valve SC1 |
OK
NG
Remove the shift solenoid valve SL1 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 1 of the shift solenoid valve SL1 - Terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 2 ·
Battery negative (-) → Terminal 1 |
Valve moves and makes an operating noise |
| *1 | Shift Solenoid Valve SL1 |
OK
NG
Check the transmission valve body assembly (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL).
There is no foreign matter on each valve and they operate smoothly.
OK
(See pageDrivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION ASSEMBLY>REMOVAL)
NG