Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential

·

[ON] denotes battery potential (+B)

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a) and (b) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch is ON
(b) STP signal is off when ST1- signal is off
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

STOP fuse

·

ECM



WIRING DIAGRAM

for Manual Transmission Models
A372109E09
0.646,4.021 1.125,4.208 0.479,0.188 10 false Battery 0.958,3.031 1.313,3.198 0.354,0.167 10 false P/I-B 0.948,0.583 1.365,0.75 0.417,0.167 10 false STOP 2.083,0.906 2.719,1.073 0.635,0.167 10 false IG2 NO.1 0.917,3.438 3.281,3.896 2.365,0.458 10 false from Certification ECU (Smart Key ECU Assembly)*1 or Ignition Switch*2 3.479,1.292 3.771,1.448 0.292,0.156 10 false A73 3.469,1.448 5.229,1.635 1.76,0.188 10 false Stop Light Switch Assembly 3.667,0.344 3.792,0.51 0.125,0.167 10 false 1 3.688,0.604 3.813,0.771 0.125,0.167 10 false 5 3.688,0.927 3.813,1.094 0.125,0.167 10 false 3 4.75,0.927 4.875,1.094 0.125,0.167 10 false 4 4.74,0.313 4.865,0.479 0.125,0.167 10 false 2 3.865,0.417 3.99,0.583 0.125,0.167 10 false B 4.552,0.417 4.677,0.583 0.125,0.167 10 false L 4.552,1.021 4.677,1.188 0.125,0.167 10 false L 3.865,0.74 3.99,0.906 0.125,0.167 10 false B 3.875,1.042 4.229,1.208 0.354,0.167 10 false GND 3.344,2.292 3.552,2.448 0.208,0.156 10 false 1R 3.375,2.115 3.49,2.271 0.115,0.156 10 false 1 3.354,2.854 3.563,3.01 0.208,0.156 10 false 1X 3.375,2.667 3.49,2.823 0.115,0.156 10 false 1 3.344,3.281 3.552,3.469 0.208,0.188 10 false 1R 3.385,3.083 3.5,3.24 0.115,0.156 10 false 2 4.927,3.281 5.135,3.438 0.208,0.156 10 false 1S 4.969,3.104 5.083,3.26 0.115,0.156 10 false 4 3.635,3 4.281,3.156 0.646,0.156 10 false IG2 MAIN 4.208,3.521 4.854,3.677 0.646,0.156 10 false IG2 MAIN 5.24,3.083 6.344,3.271 1.104,0.188 10 false Integration Relay 5.792,0.344 5.99,0.5 0.198,0.156 10 false 36 5.792,0.917 5.99,1.073 0.198,0.156 10 false 35 6.063,0.323 6.354,0.479 0.292,0.156 10 false STP 6.063,0.948 6.417,1.104 0.354,0.156 10 false ST1- 6.125,2.396 6.49,2.573 0.365,0.177 10 false A38 6.115,2.573 6.458,2.74 0.344,0.167 10 false ECM 1.313,4.208 5.177,4.427 3.865,0.219 10 false *1: w/ Entry and Start System, *2: w/o Entry and Start System


for Automatic Transmission Models
A372109E08
0.646,4.01 1.125,4.198 0.479,0.188 10 false Battery 0.969,2.667 1.323,2.833 0.354,0.167 10 false P/I-B 0.948,0.583 1.365,0.75 0.417,0.167 10 false STOP 2.052,0.896 2.688,1.063 0.635,0.167 10 false IG2 NO.1 1.406,3.26 2.5,3.823 1.094,0.563 10 false Certification ECU (Smart Key ECU Assembly) 3.458,1.271 3.75,1.427 0.292,0.156 10 false A73 3.458,1.427 5.219,1.615 1.76,0.188 10 false Stop Light Switch Assembly 3.677,0.354 3.802,0.521 0.125,0.167 10 false 1 3.677,0.646 3.802,0.813 0.125,0.167 10 false 5 3.677,0.927 3.802,1.094 0.125,0.167 10 false 3 4.74,0.906 4.865,1.073 0.125,0.167 10 false 4 4.729,0.323 4.854,0.49 0.125,0.167 10 false 2 3.865,0.438 3.99,0.604 0.125,0.167 10 false B 4.552,0.417 4.677,0.583 0.125,0.167 10 false L 4.552,1.01 4.677,1.177 0.125,0.167 10 false L 3.865,0.76 3.99,0.927 0.125,0.167 10 false B 3.875,1.031 4.229,1.198 0.354,0.167 10 false GND 3.333,2.292 3.542,2.448 0.208,0.156 10 false 1R 3.385,2.125 3.5,2.281 0.115,0.156 10 false 1 3.344,2.844 3.552,3 0.208,0.156 10 false 1X 3.385,2.677 3.5,2.833 0.115,0.156 10 false 1 3.344,3.271 3.563,3.448 0.219,0.177 10 false 1R 3.385,3.104 3.5,3.26 0.115,0.156 10 false 2 4.927,3.281 5.135,3.438 0.208,0.156 10 false 1S 4.969,3.115 5.083,3.271 0.115,0.156 10 false 4 3.635,2.979 4.281,3.135 0.646,0.156 10 false IG2 MAIN 4.219,3.5 4.865,3.656 0.646,0.156 10 false IG2 MAIN 5.24,2.99 6.344,3.177 1.104,0.188 10 false Integration Relay 5.781,0.333 5.979,0.49 0.198,0.156 10 false 7 5.781,0.927 5.979,1.083 0.198,0.156 10 false 8 6.083,0.344 6.375,0.5 0.292,0.156 10 false STP 6.073,0.917 6.427,1.073 0.354,0.156 10 false ST1- 6.115,2.365 7.01,2.521 0.896,0.156 10 false A38 6.115,2.51 6.458,2.677 0.344,0.167 10 false ECM


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
U163583E01
0.586,1.915 0.895,2.071 0.308,0.156 10 A73 0.181,0.149 0.336,0.305 0.154,0.156 10 *a 1.103,2.786 1.266,2.948 0.163,0.163 10 B 1.326,2.321 1.177,2.786 false

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A73-1 (B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL VOLTAGE)
a.
U163584E01
0.181,0.149 0.336,0.305 0.154,0.156 10 *a 2.276,2.786 2.439,2.948 0.163,0.163 10 B 2.156,2.346 2.327,2.786 false 0.586,1.922 0.895,2.078 0.308,0.156 10 A73

Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A73-5 (B) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-3 (GND) - Body ground Always Below 1 Ω




OK

4.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK ECM (STP AND ST1- VOLTAGE)
A112585C13
0.125,3.344 0.552,3.646 0.427,0.302 1.781,3.656 1.094,4.229 true 1.865,3.667 1.667,4.229 true 2.021,3.26 2.75,4.063 true 1.948,3.26 2.219,4.24 true 0.844,1.958 1.156,2.156 0.313,0.198 10 false *a 2.51,1.958 2.823,2.156 0.313,0.198 10 false *b 0.677,4.26 1.438,4.448 0.76,0.188 10 false 35(ST1)*A 1.385,4.281 2.458,4.479 1.073,0.198 10 false 36(STP)*A 2.625,4.115 3.406,4.313 0.781,0.198 10 false 8(ST1-)*B 2.083,4.292 2.76,4.458 0.677,0.167 10 false 7(STP)*B 0.219,3.385 0.677,3.583 0.458,0.198 10 false A38 0.156,2.698 0.469,2.896 0.313,0.198 10 false *c
*A for Manual Transmission Models
*B for Automatic Transmission Models
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Manual Transmission Models
Tester Connection Condition Specified Condition
A38-35 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
A38-36 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V

for Automatic Transmission Models
Tester Connection Condition Specified Condition
A38-8 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
A38-7 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V




OK

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transmission Models
Tester Connection Condition Specified Condition
A73-2 (L) - A38-36 (STP) Always Below 1 Ω
A73-4 (L) - A38-35 (ST1-) Always Below 1 Ω
A73-2 (L) or A38-36 (STP) - Body ground Always 10 kΩ or higher
A73-4 (L) or A38-35 (ST1-) - Body ground Always 10 kΩ or higher

for Automatic Transmission Models
Tester Connection Condition Specified Condition
A73-2 (L) - A38-7 (STP) Always Below 1 Ω
A73-4 (L) - A38-8 (ST1-) Always Below 1 Ω
A73-2 (L) or A38-7 (STP) - Body ground Always 10 kΩ or higher
A73-4 (L) or A38-8 (ST1-) - Body ground Always 10 kΩ or higher




OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the No. 2 engine room relay block.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-5 (B) - 1R-1 Always Below 1 Ω
A73-5 (B) or 1R-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR