Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM J

1GR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the integration relay (EFI relay) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM

for Manual Transmission Models
A413575E01
2.563,0.896 3.021,1.094 0.458,0.198 10 false AM2 0.438,0.917 1.667,1.115 1.229,0.198 10 false J/B LH-B 3.385,0.635 3.542,0.833 0.156,0.198 10 false 5 3.375,0.938 3.531,1.135 0.156,0.198 10 false 6 3.615,0.74 4.073,0.938 0.458,0.198 10 false AM2 3.615,1.052 4.073,1.25 0.458,0.198 10 false IG2 0.531,2.396 1.302,2.594 0.771,0.198 10 false P/I-B 1.573,2.229 1.885,2.427 0.313,0.198 10 false 1X 1.604,2.021 1.76,2.219 0.156,0.198 10 false 1 1.573,2.573 1.885,2.771 0.313,0.198 10 false 1R 1.604,2.396 1.76,2.594 0.156,0.198 10 false 2 2.438,2.365 3.667,2.563 1.229,0.198 10 false IG2 MAIN 3.031,2.833 4.26,3.031 1.229,0.198 10 false IG2 MAIN 3.646,2.396 5.479,2.594 1.833,0.198 10 false ENG-IG2 NO.1 4.188,3.063 5.417,3.26 1.229,0.198 10 false EFI NO.2 4.594,3.479 4.906,3.677 0.313,0.198 10 false 1S 2.094,3.635 4.083,3.833 1.99,0.198 10 false EFI MAIN NO.1 2.885,4.135 4.875,4.333 1.99,0.198 10 false EFI MAIN NO.1 4.594,3.281 4.906,3.479 0.313,0.198 10 false 11 4.594,3.917 4.906,4.115 0.313,0.198 10 false 1S 4.625,3.708 4.781,3.906 0.156,0.198 10 false 4 4.583,4.469 4.896,4.667 0.313,0.198 10 false 1S 4.635,4.271 4.792,4.469 0.156,0.198 10 false 8 3.667,4.854 4.875,5.104 1.208,0.25 10 false Integration Relay 4.594,2.229 4.906,2.427 0.313,0.198 10 false 1P 4.646,2.021 4.802,2.219 0.156,0.198 10 false 7 5.813,2.24 6.271,2.438 0.458,0.198 10 false A38 5.875,2.021 6.188,2.219 0.313,0.198 10 false 28 5.823,3.104 6.281,3.302 0.458,0.198 10 false A38 5.927,2.885 6.083,3.083 0.156,0.198 10 false 3 5.917,3.302 6.073,3.5 0.156,0.198 10 false 2 5.813,3.479 6.271,3.677 0.458,0.198 10 false A38 5.813,4.479 6.271,4.677 0.458,0.198 10 false A38 5.885,4.271 6.198,4.469 0.313,0.198 10 false 34 5.813,5.479 6.271,5.677 0.458,0.198 10 false C45 5.885,5.281 6.198,5.479 0.313,0.198 10 false 81 6.156,5.479 6.469,5.677 0.313,0.198 10 false E1 1.594,5.354 2.208,5.552 0.615,0.198 10 false IG1D 1.344,5.24 1.5,5.438 0.156,0.198 10 false 3 1.604,5.802 2.219,6 0.615,0.198 10 false E128 1.594,5.969 3.146,6.344 1.552,0.375 10 false Certification ECU (Smart Key ECU Assembly)*1 3.344,5.51 5.292,5.729 1.948,0.219 10 false *1: w/ Entry and Start System 3.365,5.823 5.365,6.094 2,0.271 10 false *2: w/o Entry and Start System 0.573,5.229 1.646,5.427 1.073,0.198 10 false Battery 6.396,6.01 6.854,6.208 0.458,0.198 10 false ECM 3.667,1.375 4.125,1.573 0.458,0.198 10 false E93 3.656,1.531 6.26,1.729 2.604,0.198 10 false Ignition Switch*2 6.198,2.073 6.813,2.271 0.615,0.198 10 false IGSW 6.167,3.094 6.479,3.292 0.313,0.198 10 false +B 6.167,3.469 6.625,3.667 0.458,0.198 10 false +B2 6.156,4.365 6.771,4.563 0.615,0.198 10 false MREL


for Automatic Transmission Models
A413576E01
0.563,2.385 1.333,2.583 0.771,0.198 10 false P/I-B 1.573,2.229 1.885,2.427 0.313,0.198 10 false 1X 1.583,2.042 1.74,2.24 0.156,0.198 10 false 1 1.573,2.573 1.885,2.771 0.313,0.198 10 false 1R 1.594,2.396 1.75,2.594 0.156,0.198 10 false 2 2.417,2.385 3.646,2.583 1.229,0.198 10 false IG2 MAIN 3.042,2.833 4.271,3.031 1.229,0.198 10 false IG2 MAIN 3.656,2.375 5.49,2.573 1.833,0.198 10 false ENG-IG2 NO.1 4.594,2.24 4.906,2.438 0.313,0.198 10 false 1P 4.667,2.01 4.823,2.208 0.156,0.198 10 false 7 5.802,2.229 6.26,2.427 0.458,0.198 10 false A38 5.875,2.031 6.188,2.229 0.313,0.198 10 false 4 5.823,3.104 6.281,3.302 0.458,0.198 10 false A38 5.885,2.896 6.042,3.094 0.156,0.198 10 false 2 5.813,3.49 6.271,3.688 0.458,0.198 10 false A38 5.906,3.292 6.063,3.49 0.156,0.198 10 false 3 4.167,3.063 5.396,3.26 1.229,0.198 10 false EFI NO.2 2.104,3.646 4.094,3.844 1.99,0.198 10 false EFI MAIN NO.1 2.844,4.135 4.833,4.333 1.99,0.198 10 false EFI MAIN NO.1 4.573,3.479 4.885,3.677 0.313,0.198 10 false 1S 4.583,3.271 4.896,3.469 0.313,0.198 10 false 11 4.583,4.469 4.896,4.667 0.313,0.198 10 false 1S 4.635,3.708 4.792,3.906 0.156,0.198 10 false 4 4.583,3.917 4.896,4.115 0.313,0.198 10 false 1S 4.635,4.26 4.792,4.458 0.156,0.198 10 false 8 5.802,4.458 6.26,4.656 0.458,0.198 10 false A38 5.875,4.26 6.188,4.458 0.313,0.198 10 false 6 5.813,5.479 6.271,5.677 0.458,0.198 10 false C45 5.875,5.281 6.188,5.479 0.313,0.198 10 false 81 3.646,4.885 6.25,5.083 2.604,0.198 10 false Integration Relay 0.583,5.188 1.656,5.385 1.073,0.198 10 false Battery 6.167,2.094 6.781,2.292 0.615,0.198 10 false IGSW 6.177,3.094 6.49,3.292 0.313,0.198 10 false +B 6.167,3.427 6.625,3.625 0.458,0.198 10 false +B2 6.156,4.365 6.771,4.563 0.615,0.198 10 false MREL 6.156,5.448 6.469,5.646 0.313,0.198 10 false E1 6.354,6.01 6.813,6.208 0.458,0.198 10 false ECM 3.594,0.896 4.208,1.094 0.615,0.198 10 false IG1D 3.344,0.781 3.5,0.979 0.156,0.198 10 false 3 3.083,1.25 3.698,1.448 0.615,0.198 10 false E128 3.042,1.406 5.917,1.625 2.875,0.219 10 false Certification ECU (Smart Key ECU Assembly)


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - BATTERY)
U155720E05
0.76,1.938 1.042,2.135 0.281,0.198 10 false 1X 0.135,0.167 0.469,0.427 0.333,0.26 10 false *a

a.

Remove the integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1X-1 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector (to Integration Relay)



OK

2.INSPECT INTEGRATION RELAY (EFI MAIN NO.1 RELAY AND IG2 MAIN NO.1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INTEGRATION RELAY (EFI MAIN NO.1 RELAY AND IG2 MAIN NO.1 RELAY)

OK

3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)

NG

REPLACE INTEGRATION RELAY

3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)
a.

Check the harness and the connectors between the integration relay and the ECM.

i.

Remove the integration relay from the engine room relay block.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transmission Models
Tester Connection Condition Specified Condition
A38-34 (MREL) - 1S-8 Always Below 1 Ω
A38-3 (+B) - 1S-11 Always Below 1 Ω
A38-2 (+B2) - 1S-11 Always Below 1 Ω
A38-34 (MREL) or 1S-8 - Body ground Always 10 kΩ or higher
A38-3 (+B) or 1S-11 - Body ground Always 10 kΩ or higher
A38-2 (+B2) or 1S-11 - Body ground Always 10 kΩ or higher

for Automatic Transmission Models
Tester Connection Condition Specified Condition
A38-6 (MREL) - 1S-8 Always Below 1 Ω
A38-2 (+B) - 1S-11 Always Below 1 Ω
A38-3 (+B2) - 1S-11 Always Below 1 Ω
A38-6 (MREL) or 1S-8 - Body ground Always 10 kΩ or higher
A38-2 (+B) or 1S-11 - Body ground Always 10 kΩ or higher
A38-3 (+B2) or 1S-11 - Body ground Always 10 kΩ or higher




b.

Check the harness and connectors between the integration relay and body ground.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1S-4 - Body ground Always Below 1 Ω





OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-81 (E1) - Body ground Always Below 1 Ω




OK

5.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (IGSW VOLTAGE)
A413832C01
1.146,0.75 1.563,1.01 0.417,0.26 0.375,3.458 0.823,3.76 0.448,0.302 2.01,1.927 2.719,2.521 true 2.427,3.5 2.604,4.25 true 2,3.313 0.875,4.25 true 1.219,0.813 1.677,1.01 0.458,0.198 10 false C45 0.458,3.521 0.917,3.719 0.458,0.198 10 false A38 2.615,2.563 3.208,2.781 0.594,0.219 10 false 81(E1) 2.302,4.281 3.073,4.5 0.771,0.219 10 false 28(IGSW)*A 0.594,4.292 1.969,4.49 1.375,0.198 10 false 4(IGSW)*B 0.25,0.156 0.563,0.354 0.313,0.198 10 false *a
*A for Manual transmission models
*B for Automatic transmission models
*a Front view of wire harness connector
(to ECM)


a.

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for Manual Transmission Models
Tester Connection Switch Condition Specified Condition
A38-28 (IGSW) - C45-81 (E1) Ignition switch ON 11 to 14 V

for Automatic Transmission Models
Tester Connection Switch Condition Specified Condition
A38-4 (IGSW) - C45-81 (E1) Ignition switch ON 11 to 14 V




OK

NG

6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND)
a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Manual Transmission Models
Tester Connection Condition Specified Condition
1P-7 - A38-28 (IGSW) Always Below 1 Ω
1P-7 or A38-28 (IGSW) - Body ground Always 10 kΩ or higher

for Automatic Transmission Models
Tester Connection Condition Specified Condition
1P-7 - A38-4 (IGSW) Always Below 1 Ω
1P-7 or A38-4 (IGSW) - Body ground Always 10 kΩ or higher




OK

7.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
Result
Result Proceed to
w/ Entry and Start System A
w/o Entry and Start System B


A

8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE ROOM RELAY BLOCK

B

10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ENGINE ROOM RELAY BLOCK)
8.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE ROOM RELAY BLOCK
a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E128-3 (IG1D) - 1R-2 Always Below 1 Ω
E128-3 (IG2D) or 1R-2 - Body ground Always 10 kΩ or higher




OK

9.CHECK ENTRY AND START SYSTEM (POWER SOURCE MODE DOES NOT CHANGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - ENGINE ROOM RELAY BLOCK)
a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the ignition switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E93-6 (IG2) - 1R-2 Always Below 1 Ω
E93-6 (IG2) or 1R-2 - Body ground Always 10 kΩ or higher




OK

11.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly (See page Engine / Hybrid System>1GR-FE (STARTING)>IGNITION SWITCH>INSPECTION).



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY