Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM (w/ Entry and Start System) › from 2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255571 THEFT DETERRENT SYSTEM(w/ Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM(w/ Entry and Start System)  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor cancel switch on the map light assembly is pressed, the sensor off signal is sent to the main body ECU (multiplex network body ECU) which causes the intrusion and tilt sensor to stop operating.


WIRING DIAGRAM

B336726E07
1.833,1 3.854,1.208 2.021,0.208 10 false Intrusion Sensor Cancel Switch 1.823,1.406 2.385,1.615 0.563,0.208 10 false R7 1.792,1.563 3.583,1.802 1.792,0.24 10 false Map Light Assembly 1.521,0.74 1.74,0.938 0.219,0.198 10 false 17 3.854,0.74 4.115,0.948 0.26,0.208 10 false 11 1.833,0.74 2.396,0.927 0.563,0.188 10 false GND9 3.354,0.74 3.917,0.927 0.563,0.188 10 false SOFF 5.01,0.74 5.229,0.938 0.219,0.198 10 false 13 5,1.406 5.479,1.625 0.479,0.219 10 false E117 5,1.563 6.625,1.99 1.625,0.427 10 false Main Body ECU (Multiplex Network Body ECU) 5.26,0.896 6.063,1.188 0.802,0.292 10 false SSW1

CAUTION / NOTICE / HINT

NOTICE:
·

If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.

·

w/ Door Control Battery:

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION



PROCEDURE

1.READ VALUE USING GTS (INTRUSION SENS OFF SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

According to the display on the GTS, read the Data List.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Intrusion Sens OFF SW Intrusion sensor cancel switch/ON or OFF ON: Intrusion sensor cancel switch on
OFF: Intrusion sensor cancel switch off
-

OK:

The indicator on the GTS switches between ON and OFF in accordance with the intrusion sensor cancel switch status.




OK

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - MAP LIGHT ASSEMBLY AND BODY GROUND)
a.

Disconnect the E117 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the R7 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E117-13 (SSW1) - R7-11 (SOFF) Always Below 1 Ω
R7-17 (GND9) - Body ground Always Below 1 Ω
E117-13 (SSW1) - Body ground Always 10 kΩ or higher
R7-11 (SOFF) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)
a.
B188803E11
2.5,1.927 2.604,1.927 2.604,1.927 2.792,1.406 true 0.958,0.458 1.063,0.458 1.063,0.458 1.333,1.115 true 2.063,1.844 2.521,2.031 0.458,0.188 10 false GND9 0.573,0.396 1.042,0.594 0.469,0.198 10 false SOFF

Remove the map light assembly (intrusion sensor cancel switch) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>INTRUSION SENSOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
11 (SOFF) - 17 (GND9) Intrusion sensor cancel switch not pressed 10 kΩ or higher
11 (SOFF) - 17 (GND9) Intrusion sensor cancel switch pressed Below 1 Ω


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE MAIN BODY ECU [MULTIPLEX NETWORKBODY ECU] (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU [MULTIPLEX NETWORKBODY ECU]

C

REPLACE MAP LIGHT ASSEMBLY (INTRUSION SENSOR CANCEL SWITCH)