Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Entry Function) › from 2017.08
RM2660E _58 Vehicle Interior _052839 THEFT DETERRENT / KEYLESS ENTRY _0255572 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Back Door Entry Unlock Function does not Operate  


DESCRIPTION

If the entry unlock function does not operate for the back door only, but the entry lock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the open switch (connection between the back door opener switch assembly and certification ECU [smart key ECU assembly]).

WIRING DIAGRAM

B423531E51
0.698,2.365 2.385,2.802 1.688,0.438 10 false Back Door Opener Switch Assembly 0.719,2.198 1.177,2.385 0.458,0.188 10 false S43 0.688,1.677 0.979,1.875 0.292,0.198 10 false 2 0.896,1.677 1.188,1.875 0.292,0.198 10 false E 2.208,1.667 2.5,1.865 0.292,0.198 10 false 1 2.198,1.135 2.49,1.333 0.292,0.198 10 false 3 2.021,1.667 2.313,1.865 0.292,0.198 10 false L 1.948,1.146 2.24,1.344 0.292,0.198 10 false UL 5.229,2.271 5.521,2.469 0.292,0.198 10 false E 5.229,1.656 5.927,1.875 0.698,0.219 10 false TSW6 5.229,1.135 5.927,1.354 0.698,0.219 10 false TSW5 4.833,2.271 5.656,2.49 0.823,0.219 10 false E130 4.833,1.219 5.469,1.427 0.635,0.208 10 false E129 4.927,1.031 5.219,1.229 0.292,0.198 10 false 5 4.896,1.563 5.188,1.76 0.292,0.198 10 false 13 4.917,2.104 5.208,2.302 0.292,0.198 10 false 11 5.604,0.469 5.896,0.667 0.292,0.198 10 false 5V 5.917,1.01 6.208,1.208 0.292,0.198 10 false 5V 5.135,2.854 6.823,3.25 1.688,0.396 10 false Certification ECU (Smart Key ECU Assembly) 4.833,1.75 5.542,1.99 0.708,0.24 10 false E129

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Check that there are no electrical key transmitter sub-assemblies in the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING GTS (B-DR OPENING OPERATION)

NG

2.READ VALUE USING GTS (B-DR OPENING OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
B-Dr Opening Operation Back door opening operation / Long, Twice or OFF Customize setting displayed -

Result
Result Proceed to
Customize setting is Long or Twice A
Customize setting is OFF B



A

3.READ VALUE USING GTS (TR/B DOOR UNLOCK SW)

B

3.READ VALUE USING GTS (TR/B DOOR UNLOCK SW)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Data List.


e.

Read the Data List according to the display on the GTS.

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Back door opener switch assembly (open switch) / ON or OFF ON: Back door opener switch assembly (open switch) pressed
OFF: Back door opener switch assembly (open switch) not pressed
·

Displays whether the back door opener switch assembly (open switch) is on or off.

·

Use this Data List item to help determine if there is a switch malfunction when the back door open function does not operate.



OK:

The GTS display changes correctly in response to the operation of the back door opener switch assembly.




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
4.CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the S43 back door opener switch assembly connector.


b.

Disconnect the E129 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S43-3 (UL) - E129-5 (TSW5) Always Below 1 Ω
S43-3 (UL) or E129-5 (TSW5) - Body ground Always 10 kΩ or higher




OK

5.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (OPEN SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (OPEN SWITCH)
a.

Remove the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL).


b.

Inspect the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION).



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE BACK DOOR OPENER SWITCH ASSEMBLY