If the entry lock and unlock functions do not operate for the back door only, the request code may not be being transmitted from the back door. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver assembly is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU [smart key ECU assembly] and electrical key antenna [outside luggage compartment]), or there may be electric wave interference.
The entry and start system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING).
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Check that there are no electrical key transmitter sub-assemblies in the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION).
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B27A8 is not output | A |
| DTC B27A8 is output | B |
A
B
| *a | Approximately 0.3 m (0.984 ft.) |
Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage compartment) and perform an entry back door open/lock function check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the electrical key antenna (outside luggage compartment)
When the electrical key transmitter sub-assembly is brought near the electrical key antenna (outside luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
When checking the operation of the entry lock function several times, it can be operated up to 2 times consecutively. To operate the function 3 times or more consecutively, the doors need to be unlocked once. However, this is only for the entry lock function, other door lock operations, such as a wireless door lock operation can be performed consecutively. (w/ Double Locking System)
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Tr/B-Door Lock SW | Back door opener switch assembly (lock switch) / ON or OFF | ON: Back door opener switch assembly (lock switch) pressed
OFF: Back door opener switch assembly (lock switch) not pressed |
·
Displays whether the back door opener switch assembly (lock switch) is on or off. ·
Use this Data List item to help determine if there is a switch malfunction when the back door lock function does not operate. |
| Tr/B-Door Unlock SW | Back door opener switch assembly (open switch) / ON or OFF | ON: Back door opener switch assembly (open switch) pressed
OFF: Back door opener switch assembly (open switch) not pressed |
·
Displays whether the back door opener switch assembly (open switch) is on or off. ·
Use this Data List item to help determine if there is a switch malfunction when the back door open function does not operate. |
The GTS display changes correctly in response to the operation of the back door opener switch assembly.
OK
NG
Check the following antenna in key diagnostic mode.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Check the electrical key antenna (outside luggage compartment):
When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless buzzer sounds.
Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| Result | Proceed to |
|---|---|
| Wireless buzzer does not sound | A |
| Wireless buzzer sounds | B |
A
B
Disconnect the K48 electrical key antenna (outside luggage compartment) connector.
Disconnect the E129 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K48-2 (ANTE8) - E129-2 (CLG8) | Always | Below 1 Ω |
| K48-1 (CLGB) - E129-1 (CG8B) | Always | Below 1 Ω |
| K48-2 (ANTE8) or E129-2 (CLG8) - Body ground | Always | 10 kΩ or higher |
| K48-1 (CLGB) or E129-1 (CG8B) - Body ground | Always | 10 kΩ or higher |
Connect the E129 certification ECU (smart key ECU assembly) connector.
Disconnect the K48 electrical key antenna (outside luggage compartment) connector.
OK
NG
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU [Smart Key ECU Assembly]) |
b | Waveform 1 |
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| E129-2 (CLG8) - E130-11 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Back door opener switch assembly off → on |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 1) |
| E129-1 (CG8B) - E130-11 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly brought outside vehicle 3.
All doors closed 4.
Back door opener switch assembly off → on |
2 V/DIV., 500 ms/DIV. | Pulse generation (See waveform 1) |
OK
NG
Connect all connectors and check that the entry lock and unlock functions operate (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B
Disconnect the S43 back door opener switch assembly connector.
Disconnect the E129 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S43-1 (L) - E129-13 (TSW6) | Always | Below 1 Ω |
| S43-3 (UL) - E129-5 (TSW5) | Always | Below 1 Ω |
| S43-2 (E) - Body ground | Always | Below 1 Ω |
| S43-1 (L) or E129-13 (TSW6) - Body ground | Always | 10 kΩ or higher |
| S43-3 (UL) or E129-5 (TSW5) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>REMOVAL).
Inspect the back door opener switch assembly (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR OPENER SWITCH>INSPECTION).
OK
NG
Connect all connectors and check that the entry lock and unlock functions operate (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Entry Function)>OPERATION CHECK).
| Result | Proceed to |
|---|---|
| Entry function does not operate normally | A |
| Entry function operates normally | B |
A
B