Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2017.08
RM2660E _58 Vehicle Interior _052843 SUPPLEMENTAL RESTRAINT SYSTEMS _0255605 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY (for Interlock Type)

a.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B495629C01
1.313,1.469 1.615,1.729 0.302,0.26 2.865,3.698 3.125,3.917 0.26,0.219 5.823,1.51 6.042,1.698 0.219,0.188 0.948,1.396 1.542,1.396 1.542,1.396 1.542,1.177 true 0.958,0.792 1.552,0.792 1.552,0.792 1.552,1.115 true 6.042,2.177 5.479,2.177 5.479,2.177 5.729,1.563 true 3.167,3.615 3.615,4.271 true 5.792,1.49 6.521,1.167 true 2.583,3.167 3.135,3.531 true 1.469,1.729 1.469,2.292 true 3,3.917 3,4.479 true 6.042,1.604 6.458,1.604 true 1.854,0.417 2.198,0.74 0.344,0.323 12 false *A 0.76,1.302 1.073,1.458 0.313,0.156 10 false *a 1.406,2.333 1.719,2.49 0.313,0.156 10 false *b 3.583,4.292 3.896,4.448 0.313,0.156 10 false *c 0.771,0.698 1.083,0.854 0.313,0.156 10 false *d 5.323,0.406 5.667,0.729 0.344,0.323 12 false *B 3.458,2.646 3.802,2.969 0.344,0.323 12 false *C 6.094,2.094 6.406,2.25 0.313,0.156 10 false *d 6.563,1.052 6.875,1.208 0.313,0.156 10 false *a 2.406,3.052 2.719,3.208 0.313,0.156 10 false *a 2.948,4.521 3.26,4.677 0.313,0.156 10 false *b 6.521,1.531 6.833,1.688 0.313,0.156 10 false *b
*A Flat Cable (Visible Type), w/o Steering Haeter *B Flat Cable (Visible Type), w/ Steering Heater
*C Colored Roller (Visible Type) - -
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn



b.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly .

·

When rotating the spiral cable sub-assembly , make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B459513C01
0,0 0,0 false
V100144

Interlock
V100135

Counterclockwise


While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.


HINT:

The interlock operates at the top and bottom of the connector.



ii.
B459514

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B459515C01
0,0 0,0 false
V100144

Interlock
V100135

Counterclockwise


While pushing on the interlock, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.




c.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B495629C01
1.313,1.469 1.615,1.729 0.302,0.26 2.865,3.698 3.125,3.917 0.26,0.219 5.823,1.51 6.042,1.698 0.219,0.188 0.948,1.396 1.542,1.396 1.542,1.396 1.542,1.177 true 0.958,0.792 1.552,0.792 1.552,0.792 1.552,1.115 true 6.042,2.177 5.479,2.177 5.479,2.177 5.729,1.563 true 3.167,3.615 3.615,4.271 true 5.792,1.49 6.521,1.167 true 2.583,3.167 3.135,3.531 true 1.469,1.729 1.469,2.292 true 3,3.917 3,4.479 true 6.042,1.604 6.458,1.604 true 1.854,0.417 2.198,0.74 0.344,0.323 12 false *A 0.76,1.302 1.073,1.458 0.313,0.156 10 false *a 1.406,2.333 1.719,2.49 0.313,0.156 10 false *b 3.583,4.292 3.896,4.448 0.313,0.156 10 false *c 0.771,0.698 1.083,0.854 0.313,0.156 10 false *d 5.323,0.406 5.667,0.729 0.344,0.323 12 false *B 3.458,2.646 3.802,2.969 0.344,0.323 12 false *C 6.094,2.094 6.406,2.25 0.313,0.156 10 false *d 6.563,1.052 6.875,1.208 0.313,0.156 10 false *a 2.406,3.052 2.719,3.208 0.313,0.156 10 false *a 2.948,4.521 3.26,4.677 0.313,0.156 10 false *b 6.521,1.531 6.833,1.688 0.313,0.156 10 false *b
*A Flat Cable (Visible Type), w/o Steering Haeter *B Flat Cable (Visible Type), w/ Steering Heater
*C Colored Roller (Visible Type) - -
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.



Hide 84306 2.INSPECT SPIRAL CABLE SUB-ASSEMBLY (for Pin Lock Type)

a.
B496124C01
1.635,2 2.052,2.438 0.417,0.438 1,2.302 1.417,1.885 true 1.385,1.75 0.969,1.177 true 0.813,2.292 1.125,2.448 0.313,0.156 10 false *a 1.646,2.01 1.833,2.177 0.188,0.167 10 true *b 0.813,1.063 1.125,1.219 0.313,0.156 10 false *c
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn


Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.



b.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B459529C01
0,0 0,0 false
V100135

Counterclockwise


Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.



ii.
B459530

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B459531C01
0,0 0,0 false
V100135

Clockwise


Rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.



iv.
B496124C01
1.635,2 2.052,2.438 0.417,0.438 1,2.302 1.417,1.885 true 1.385,1.75 0.969,1.177 true 0.813,2.292 1.125,2.448 0.313,0.156 10 false *a 1.646,2.01 1.833,2.177 0.188,0.167 10 true *b 0.813,1.063 1.125,1.219 0.313,0.156 10 false *c
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn


Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 3.INSTALL SPIRAL CABLE (w/ Steering Angle Sensor)

NOTICE:

If the steering sensor is installed to a misaligned spiral cable, DTCs for an abnormal steering sensor value such as DTC C1433 are stored and it is impossible to repair them. If this happens, replace the spiral cable sub-assembly with a new one.


a.
B420310C05
2.04,0.859 1.57,0.726 false 3.19,0.768 2.752,0.91 false 1.373,0.612 1.570,0.761 0.198,0.149 10 *a 3.213,0.663 3.384,0.812 0.171,0.149 10 *a
*a Pin


Align the 2 pins of the spiral cable with the locations shown in the illustration and attach the 6 claws to install the spiral cable to the steering sensor.

NOTICE:

Do not remove the lock pin before the spiral cable is installed to the steering sensor.



b.

Remove the lock pin from the steering sensor.


Hide 4.INSTALL SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable sub-assembly with sensor with the battery connected and the ignition switch on.

·

Do not rotate the spiral cable sub-assembly with sensor with the battery connected and the ignition switch on.

·

When rotating the spiral cable sub-assembly with sensor to check the operation of the spiral cable sub-assembly (checking for abnormal noise, checking the DTC, Data list, etc.) make sure to perform the inspection with the steering wheel assembly installed.

·
B262558C12
0.938,1.823 1.25,2.021 0.313,0.198 10 true *a
*a Lock Pin


for Pin Lock Type:

When replacing the spiral cable sub-assembly with sensor with a new one, remove the lock pin before installing the steering wheel assembly.



a.

Set the turn signal switch to the neutral position.

NOTICE:

If it is not in the neutral position, the pin of the turn signal switch may be snapped.



b.

Attach the 3 claws to install the spiral cable sub-assembly.


c.

Connect each connector.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



Hide 5.ADJUST SPIRAL CABLE (for Interlock Type)

NOTICE:

Do not adjust the spiral cable sub-assembly with the battery connected and the ignition switch ON.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the battery negative (-) terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B495636C01
2.271,4.229 2.979,4.573 true 1.51,3.667 2.219,4.01 true 6.458,2.563 6.771,1.938 true 0.948,2.281 0.635,2.906 true 0.531,1.594 0.948,2.177 true 6.396,2.656 5.958,3.25 true 1.74,0.271 2.156,0.656 0.417,0.385 12 false *A 1.333,3.552 1.646,3.708 0.313,0.156 10 false *a 3.031,4.521 3.344,4.677 0.313,0.156 10 false *b 0.375,1.448 0.688,1.604 0.313,0.156 10 false *c 5.302,0.281 5.719,0.667 0.417,0.385 12 false *B 3.458,2.521 3.875,2.906 0.417,0.385 12 false *C 0.542,2.927 0.854,3.083 0.313,0.156 10 false *a 6.781,1.781 6.979,1.99 0.198,0.208 10 false *a 5.844,3.24 6.156,3.396 0.313,0.156 10 false *c
*A Flat Cable (Visible Type), w/o Steering Haeter *B Flat Cable (Visible Type), w/ Steering Heater
*C Colored Roller (Visible Type) - -
*a Check Window *b Colored Roller
*c Top of Flat Cable U-turn - -



d.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

When rotating the spiral cable sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B495633C01
0,0 0,0 false
V100144

Interlock
V100135

Counterclockwise


While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.



ii.
B495634

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B495635C01
0,0 0,0 false
V100144

Interlock
V100135

Clockwise


While pushing on the interlock, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.



iv.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B495636C01
2.271,4.229 2.979,4.573 true 1.51,3.667 2.219,4.01 true 6.458,2.563 6.771,1.938 true 0.948,2.281 0.635,2.906 true 0.531,1.594 0.948,2.177 true 6.396,2.656 5.958,3.25 true 1.74,0.271 2.156,0.656 0.417,0.385 12 false *A 1.333,3.552 1.646,3.708 0.313,0.156 10 false *a 3.031,4.521 3.344,4.677 0.313,0.156 10 false *b 0.375,1.448 0.688,1.604 0.313,0.156 10 false *c 5.302,0.281 5.719,0.667 0.417,0.385 12 false *B 3.458,2.521 3.875,2.906 0.417,0.385 12 false *C 0.542,2.927 0.854,3.083 0.313,0.156 10 false *a 6.781,1.781 6.979,1.99 0.198,0.208 10 false *a 5.844,3.24 6.156,3.396 0.313,0.156 10 false *c
*A Flat Cable (Visible Type), w/o Steering Haeter *B Flat Cable (Visible Type), w/ Steering Heater
*C Colored Roller (Visible Type) - -
*a Check Window *b Colored Roller
*c Top of Flat Cable U-turn - -


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 6.ADJUST SPIRAL CABLE (for Pin Lock Type)

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B496276C01
1.469,1.479 1.813,1.802 0.344,0.323 1.167,3.198 0.813,2.74 true 0.708,2.448 0.323,1.802 true 1.229,3.135 1.542,3.292 0.313,0.156 10 false *a 0.156,1.677 0.469,1.833 0.313,0.156 10 false *c 1.479,1.49 1.677,1.667 0.198,0.177 10 true *b
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn


Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.



d.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B496277C01
0,0 0,0 false
V100135

Counterclockwise


Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.



ii.
B496278

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B496279C01
0,0 0,0 false
V100135

Clockwise


Rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.



iv.
B496276C01
1.469,1.479 1.813,1.802 0.344,0.323 1.167,3.198 0.813,2.74 true 0.708,2.448 0.323,1.802 true 1.229,3.135 1.542,3.292 0.313,0.156 10 false *a 0.156,1.677 0.469,1.833 0.313,0.156 10 false *c 1.479,1.49 1.677,1.667 0.198,0.177 10 true *b
*a Check Window
*b Matchmark
*c Top of Flat Cable U-turn


Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The top of the flat cable U-turn can be checked from the check window.


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 45286B 7.INSTALL UPPER STEERING COLUMN COVER

Hide 8.INSTALL LOWER STEERING COLUMN COVER

Hide 45100 9.INSTALL STEERING WHEEL ASSEMBLY

Hide 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 12. CHECK SRS WARNING LIGHT