Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2017.08
RM2660E _56 Audio / Visual / Telematics _052828 AUDIO / VIDEO _0255487 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) Y

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the audio and visual system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
·

When troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.

·

Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.

·

The following 5 items are important points in problem analysis:

What Vehicle model, system name
When Date, time, occurrence frequency
Where Road conditions
Under what conditions? Driving conditions, weather conditions
How did it happen? Problem symptoms


Result:
Proceed to
NEXT



NEXT

3.INSPECT BATTERY VOLTAGE
3.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage with the engine switch off.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery.


Result:
Proceed to
NEXT



NEXT

4.CHECK CABIN
4.CHECK CABIN
a.

Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.

OK:

Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.


HINT:
·

A humid cabin and a rapid change in temperature may lead to condensation. Condensation in the cabin may cause a short circuit.

·

The audio and visual system may not operate normally when the temperature is -20°C (-4°F) or less, or 65°C (149°F) or higher.




Result:
Proceed to
OK
NG



OK

5.CHECK CAN COMMUNICATION SYSTEM*

NG

SET CABIN TO APPROPRIATE TEMPERATURE

5.CHECK CAN COMMUNICATION SYSTEM*

Result:
Result Proceed to
CAN DTCs are not output A
CAN DTCs are output (for LHD with Central Gateway ECU) B
CAN DTCs are output (for LHD without Central Gateway ECU) C
CAN DTCs are output (for RHD with Central Gateway ECU) D
CAN DTCs are output (for RHD without Central Gateway ECU) E



A

6.DTC CLEAR*

B

C

D

E

6.DTC CLEAR*

NEXT

7.RECHECK FOR DTC*
7.RECHECK FOR DTC*
a.

Refer to DTC Check/Clear.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

HINT:
·

Even if the malfunction symptom is not confirmed, check for diagnostic trouble codes. This is because the system stores past diagnostic trouble codes.

·

After the check using the GTS, check the "System Check Mode" screen as necessary.

·

Check the diagnostic trouble code and inspect the area code indicates.




Result:
Result Proceed to
DTC is output A
DTC is not output B



A

10.CHECK CIRCUIT

B

8.PROBLEM SYMPTOMS TABLE
8.PROBLEM SYMPTOMS TABLE
a.

Refer to Problem Symptoms Table.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B


HINT:

If the symptom does not recur and no DTC is output, perform the symptom reproduction method .

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING




A

9.CHECK ECU TERMINAL ARRANGEMENT BASED ON MALFUNCTION SYMPTOM

B

10.CHECK CIRCUIT
9.CHECK ECU TERMINAL ARRANGEMENT BASED ON MALFUNCTION SYMPTOM

NEXT

10.CHECK CIRCUIT
10.CHECK CIRCUIT
Result:
Proceed to
NEXT



NEXT

11.RECHECK FOR DIAGNOSTIC TROUBLE CODE
11.RECHECK FOR DIAGNOSTIC TROUBLE CODE
HINT:

After clearing DTCs, recheck for DTCs.


Result:
Proceed to
NEXT



NEXT

12.PERFORM CONFIRMATION TEST
12.PERFORM CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END