Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2017.08
RM2660E _56 Audio / Visual / Telematics _052829 NAVIGATION / MULTI INFO DISPLAY _0255494 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The multi-media module receiver assembly receives a reverse signal from the park/neutral position switch assembly.

WIRING DIAGRAM

U166562E01
3.118,1.501 4.468,1.922 1.350,0.421 10 Park/Neutral Position Switch Assembly 5.418,1.585 5.845,1.769 0.427,0.184 10 F77 5.418,1.744 6.751,2.089 1.333,0.345 10 Multi-media Module Receiver Assembly 3.118,1.346 3.624,1.530 0.506,0.184 10 C24 2.27,1.153 2.966,1.336 0.696,0.184 10 BKUP LP 0.313,1.005 1.747,1.354 1.434,0.349 10 from IG1 NO.2 Relay 3.931,0.913 4.195,1.097 0.264,0.184 10 RL 3.303,0.924 3.567,1.108 0.264,0.184 10 RB 3.108,0.916 3.372,1.099 0.264,0.184 10 1 5.657,1.01 5.990,1.194 0.334,0.184 10 REV 5.352,0.922 5.592,1.106 0.240,0.184 10 57 4.21,0.922 4.336,1.106 0.125,0.184 10 2 2.429,1.07 2.729,1.127 0.3,0.057

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION).


PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E285964

Enter the "Vehicle Signal Check Mode" screen. [Refer to check Vehicle Signal in Operation Check (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK)].


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
2.CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY
a.
U166458E01
1.736,0.368 2.067,0.552 0.332,0.184 10 F77 1.781,1.639 2.276,1.822 0.495,0.184 10 REV 0.2,0.03 0.532,0.214 0.332,0.184 10 *a 2.437,1.353 2.333,1.712 2.333,1.712 2.207,1.712 false

Disconnect the multi-media module receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F77-57 (REV) - Body ground Engine switch on (IG), shift lever in R 7.5 to 14 V
F77-57 (REV) - Body ground Engine switch on (IG), shift lever not in R Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Multi-media Module Receiver Assembly)



OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the F77 multi-media module receiver assembly connector.


b.

Disconnect the C24 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-57 (REV) - C24-2 (RL) Always Below 1 Ω
F77-57 (REV) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)
a.
U166426E01
0.489,0.604 0.780,0.816 0.291,0.212 10 RB 1.554,0.246 1.846,0.458 0.291,0.212 10 C24 0.046,0.033 0.337,0.245 0.291,0.212 10 *a 1.543,1.059 0.98,0.709 0.98,0.709 0.819,0.709 false

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-1 (RB) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/neutral Position Switch Assembly)

Result
Result Proceed to
OK (for AB60F) A
OK (for AE80F) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR