Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2017.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM C

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17D0  Center Differential Lock Control SW Circuit  


DESCRIPTION

This DTC is output when a malfunction is detected in the center differential lock switch (integration control and panel assembly)*1 or center differential lock switch*2.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P17D0
1.

While the ignition switch is turned to ON or directly after the ignition switch is turned to ON

2.

Center differential lock switch stuck ON

3.

0.3 seconds or more when ignition switch is turned to ON, or 60 seconds or more with ignition switch ON

4.

1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Center differential lock switch (integration control and panel assembly)*1

·

Center differential lock switch*2



*1: for Automatic Transmission w/ Entry and Start System

*2: except Automatic Transmission w/ Entry and Start System


WIRING DIAGRAM

C346659E04
0.969,1.25 3.823,1.719 2.854,0.469 10 false Center Differential Lock Switch (Integration Control and Panel Assembly)*1 1.438,2.927 3.802,3.198 2.365,0.271 10 false Center Differential Lock Switch*2 0.969,1.052 1.26,1.24 0.292,0.188 10 false V9 3.167,0.521 3.563,0.771 0.396,0.25 10 false 9 1.427,0.552 1.667,0.74 0.24,0.188 10 false 5 2.781,0.552 3.177,0.729 0.396,0.177 10 false CPU 1.448,2.719 2.781,3 1.333,0.281 10 false G12 4.719,2.948 5.01,3.135 0.292,0.188 10 false A27 4.698,3.156 6.521,3.375 1.823,0.219 10 false 4 Wheel Drive Control ECU 4.573,2.125 4.865,2.271 0.292,0.146 10 false 14 5.042,2.115 5.344,2.323 0.302,0.208 10 false DL 5.917,1.208 6.177,1.406 0.26,0.198 10 false IG 0.51,3.563 4.302,3.875 3.792,0.313 10 false *1: for Automatic Transmission w/ Entry and Start System 0.5,3.969 5.385,4.25 4.885,0.281 10 false *2: except Automatic Transmission w/ Entry and Start System 1.448,2.094 1.615,2.313 0.167,0.219 10 false 1 3.198,2.104 3.594,2.354 0.396,0.25 10 false 4 2.813,2.125 3.208,2.302 0.396,0.177 10 false CPU 1.656,0.552 1.958,0.76 0.302,0.208 10 false E 1.646,2.083 1.948,2.292 0.302,0.208 10 false E

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - CENTER DIFFERENTIAL LOCK SWITCH)
a.

Disconnect the A27 4 wheel drive control ECU connector.


b.

for Automatic Transmission w/ Entry and Start System:

Disconnect the V9 center differential lock switch (integration control and panel assembly) connector.


c.

except Automatic Transmission w/ Entry and Start System:

Disconnect the G12 center differential lock switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Automatic Transmission w/ Entry and Start System:
Tester Connection Condition Specified Condition
A27-14 (DL) - V9-9 (CPU) Always Below 1 Ω
V9-5 (E) - Body ground Always Below 1 Ω
A27-14 (DL) or V9-9 (CPU) - Body ground Always 10 kΩ or higher

except Automatic Transmission w/ Entry and Start System:
Tester Connection Condition Specified Condition
A27-14 (DL) - G12-4 (CPU) Always Below 1 Ω
G12-1 (E) - Body ground Always Below 1 Ω
A27-14 (DL) or G12-4 (CPU) - Body ground Always 10 kΩ or higher




OK

2.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY OR CENTER DIFFERENTIAL LOCK SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INTEGRATION CONTROL AND PANEL ASSEMBLY OR CENTER DIFFERENTIAL LOCK SWITCH
C331266E15
1.229,1.104 0.865,0.594 0.865,0.594 0.646,0.594 true 1.51,1.438 1.927,1.948 1.927,1.948 2.115,1.948 true 0.063,0 0.26,0.198 0.198,0.198 10 false *a 0.49,0.531 0.635,0.719 0.146,0.188 10 false E 2.156,1.865 2.594,2.052 0.438,0.188 10 false CPU

a.

for Automatic Transmission w/ Entry and Start System:

Disconnect the V9 center differential lock switch (integration control and panel assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (CPU) - 5 (E) Switch not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Center Differential Lock Switch (Integration Control and Panel Assembly))


C381468E01
2.323,1.458 2.323,2.042 2.323,2.042 2.49,2.042 true 1.271,2.042 1.438,2.042 1.438,2.042 1.438,1.458 true 0.948,1.948 1.406,2.146 0.458,0.198 10 false CPU 2.552,1.948 3.01,2.146 0.458,0.198 10 false E 0.083,0.083 0.417,0.333 0.333,0.25 10 false *a

c.

except Automatic Transmission w/ Entry and Start System:

Disconnect the G12 center differential lock switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (CPU) - 1 (E) Switch not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Center Differential Lock Switch)

Result:
Result Proceed to
OK for LHD A
for RHD B
NG for Automatic Transmission w/ Entry and Start System C
for Manual Transmission w/ Entry and Start System D
w/o Entry and Start System E




A

B

C

D

E