Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER (w/ Towing Hitch) › from 2019.08
RM2660E _59 Vehicle Exterior _052857 EXTERIOR PANELS / TRIM _0255831 REAR BUMPER(w/ Towing Hitch) A

EXTERIOR PANELS / TRIM  REAR BUMPER(w/ Towing Hitch)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:

If the bumper is damaged, there is a possibility that the installation area of the blind spot monitor sensor may be deformed and the blind spot monitor system may not operate correctly, so visually inspect the blind spot monitor sensor installation area (frame, stud bolt) to make sure it is not dented or bent.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>OPERATION CHECK

If the visual inspection finds a problem, check the installation condition of the blind spot monitor sensor, and adjust the installation position of the blind spot monitor sensor as necessary.


PROCEDURE

Hide 76626E 1.REMOVE REAR QUARTER PANEL MUDGUARD LH

Hide 76625G 2.REMOVE REAR QUARTER PANEL MUDGUARD RH

Hide 52162B 3.REMOVE REAR BUMPER NO. 1 PLATE (for Step)

a.

Put protective tape around the rear bumper No. 1 plate.


b.

Detach the 20 claws and remove the rear bumper No. 1 plate.

B422067C01
0,0 0,0 false
V100155

Protective Tape - -



Hide 52159 4.REMOVE REAR BUMPER COVER

a.
B414824C02
0,0 0,0 false
V100155

Protective Tape


Put protective tape around the bumper cover.

HINT:

Use the same procedure for the other side.



b.
B422068

Open the tail gate and remove the 4 clips.


c.

Close the tail gate.


d.
B422069C01
2.516,1.99 2.516,2.614 false 2.644,2.37 2.644,2.448 2.644,2.448 2.516,2.448 false 2.434,2.624 2.589,2.805 0.156,0.181 10 *a
*a Bolt


Remove the 2 bolts, 6 screws and 2 clips.


e.
B422070

Remove the 5 bolts.


f.
B414827

Detach the 7 claws.

HINT:

Use the same procedure for the other side.



g.
B422072

Remove the rear bumper cover.


h.

w/ TOYOTA Parking Assist-sensor System:

Disconnect the No. 2 frame wire connector.


Hide 58724B 5.REMOVE NO. 2 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

a.
B414832

Remove the 2 screws, 2 grommets and No. 2 luggage compartment side cover protector.


Hide 58723B 6.REMOVE NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

HINT:

Use the same procedure described for the LH side.


Hide 81561D 7.REMOVE REAR COMBINATION LIGHT ASSEMBLY LH

Hide 81551D 8.REMOVE REAR COMBINATION LIGHT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52563D 9.REMOVE REAR BUMPER UPPER RETAINER LH

a.
B181015

Detach the 2 clips and remove the rear bumper upper retainer LH.


Hide 52562E 10.REMOVE REAR BUMPER UPPER RETAINER RH

HINT:

Use the same procedure described for the LH side.


Hide 52156A 11.REMOVE REAR BUMPER SIDE SUPPORT LH

a.
B414829

Remove the 3 screws.


b.

Detach the 6 claws and remove the rear bumper side support LH.


Hide 52155A 12.REMOVE REAR BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure described for the LH side.


Hide 52172B 13.REMOVE REAR BUMPER NO. 2 REINFORCEMENT

a.
B181019

Remove the 2 bolts and rear bumper No. 2 reinforcement.


Hide 57615C 14.REMOVE REAR BUMPER ARM BRACKET

a.
B414830

Remove the bolt and rear bumper arm bracket.

HINT:

Use the same procedure for both bumper arm brackets.



Hide 57616B 15.REMOVE REAR BUMPER ARM BRACKET LH

a.
B414831

Detach the clamp.


b.

Remove the 2 bolts and rear bumper arm bracket LH.