The stop light switch signal is input to the skid control ECU and the skid control ECU detects the status of brake operation.
The skid control ECU has an open detection circuit.
If an open in the stop light switch input line or GND side stop light circuit is detected when the stop light switch is off, this DTC is stored.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1249 | The ECU terminal IG1 voltage is 9.5 to 17.0 V, ABS is not operating, and an open in the stop light switch circuit continues for 3 seconds or more. | ·
Stop light switch circuit ·
Harness or connector ·
Stop light control relay assembly ·
Skid control ECU (Master cylinder solenoid) |
When replacing the master cylinder solenoid, perform zero point calibration (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1380
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output (for LHD) | B |
| DTC is output (for RHD) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Turn the ignition switch off.
Disconnect the skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-7 (STP) - Body ground | Brake pedal depressed | 8 to 14 V |
| Brake pedal released | Below 1.5 V |
| *a | Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid]) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1380
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1380
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the stop light control relay assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A39-8 (OUT) - Body ground | Brake pedal depressed | 8 to 14 V |
| Brake pedal released | Below 1.5 V |
| *a | Component with harness connected
(Stop Light Control Relay Assembly) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Start the engine.
Depress the brake pedal several times to test the stop light circuit.
Check if the same DTC is output (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output (for LHD) | B |
| DTC is output (for RHD) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C