Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1235  Foreign Object is Attached on Tip of Front Speed Sensor RH  C1236  Foreign Object is Attached on Tip of Front Speed Sensor LH  


DESCRIPTION

The speed sensor detects wheel speed and sends the appropriate signals to the ECU. These signals are used to control the Multi-terrain ABS, EBD, BA, VSC, A-TRC, CRAWL and hill-start assist control systems. This speed sensor contains a sensor IC, which consists of 2 MREs (Magnetic Resistance Element). The speed sensor rotor, which consists of 48 sets of N and S poles that are arranged in a circle, is integrated with the inner race of the hub bearing.

To detect the rotation direction, the output waves are used to determine the relationship of the pulses that are generated by 2 MREs. Upon receiving this signal, the sensor IC outputs a forward or backward wave to the skid control ECU.

C173114E02
1.895,0.514 2.85,0.705 0.955,0.191 10 Speed Sensor 1.512,1.263 2.006,1.417 0.494,0.154 10 MRE A 1.512,1.562 2.006,1.716 0.494,0.154 10 MRE B 2.251,1.394 2.893,1.548 0.642,0.154 10 Sensor IC 4.015,2.013 4.657,2.204 0.642,0.191 10 Backward 6.263,0.507 6.991,0.698 0.728,0.191 10 High speed 5.647,0.0020 6.375,0.193 0.728,0.191 10 Low speed 6.693,1.268 7.074,1.411 0.381,0.143 10 2.6 V 6.693,1.479 7.074,1.621 0.381,0.143 10 1.4 V 6.693,1.71 7.074,1.852 0.381,0.143 10 0.7 V 5.419,2.013 5.992,2.162 0.573,0.149 10 Forward 0.076,2.384 2.697,2.575 2.622,0.191 10 Speed Sensor Rotor (Bearing Inner Race) 3.237,1.338 3.762,1.488 0.524,0.149 10 to ECU 3.177,1.088 3.398,1.279 0.221,0.191 10 (+) 3.177,1.768 3.361,1.959 0.184,0.191 10 (-) 5.523,1.224 5.523,0.083 5.523,0.083 5.6,0.083 false 6.168,1.226 6.168,0.581 6.168,0.581 6.228,0.581 false

DTC Code DTC Detection Condition Trouble Area
C1235
C1236
Noise in the speed sensor signals occurs 75 times or more for 5 seconds when the vehicle speed is 20 km/h (12 mph) or more.
·

Front speed sensor RH

·

Front speed sensor LH

·

Speed sensor rotor

·

Sensor installation

·

Skid control ECU (Master cylinder solenoid)



HINT:
·

DTC C1235 is for the front speed sensor RH.

·

DTC C1236 is for the front speed sensor LH.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform zero point calibration (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (FR/FL SPEED OPEN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open circuit detection/Error or Normal Normal -
FL Speed Open Front speed sensor LH open circuit detection/Error or Normal Normal -


d.

Check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CHECK FOR INTERMITTENT PROBLEMS).

OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (FR/FL WHEEL SPEED, FR/FL WHEEL DIRECTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING GTS (FR/FL WHEEL SPEED, FR/FL WHEEL DIRECTION)
a.

Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH reading/min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front wheel sensor LH reading/min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) Actual wheel speed No large fluctuations when driving at a constant speed.

OK:

The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed.



b.

Check that the sensor signal conforms to the wheel direction.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Wheel Direction Front wheel direction RH / Forward or Back Forward: Forward
Back: Back
-
FL Wheel Direction Front wheel direction LH / Forward or Back Forward: Forward
Back: Back
-

OK:

The wheel direction is displayed correctly.



Result:
Proceed to
OK
NG



OK

3.PERFORM SIGNAL CHECK

NG

4.INSPECT FRONT SPEED SENSOR INSTALLATION
3.PERFORM SIGNAL CHECK
a.

Check if test mode (signal check) DTCs are output.

HINT:

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.



Result:
Result Proceed to
Test mode (signal check) DTC is output. A
Test mode (signal check) DTC is not output. B



A

4.INSPECT FRONT SPEED SENSOR INSTALLATION

B

10.RECONFIRM DTC
4.INSPECT FRONT SPEED SENSOR INSTALLATION
a.

Check the speed sensor installation (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION).

OK:

The installation bolt is tightened properly.

There is no clearance between the sensor and front steering knuckle.


NOTICE:

Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).


Result:
Proceed to
OK
NG




OK

5.INSPECT SPEED SENSOR TIP

NG

5.INSPECT SPEED SENSOR TIP
a.

b.

Check the sensor tip.

OK:

No scratches or foreign matter on the sensor tip.NOTICE:


NOTICE:

Check the speed sensor signal after cleaning/replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).



Result:
Proceed to
OK
NG



OK

6.INSPECT FRONT SPEED SENSOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

6.INSPECT FRONT SPEED SENSOR
a.

Install the front speed sensor.


b.

Turn the ignition switch off.


c.

Disconnect the z17 and/or z18 front speed sensor connector.


d.
C173117E24
0.156,0.833 0.552,1.083 0.396,0.25 0.156,1.104 0.552,1.354 0.396,0.25 1.594,1.094 1.302,1.292 true 1.76,1.094 2.135,1.313 true 0.156,0 0.375,0.208 0.219,0.208 10 false *a 0.24,0.844 0.49,1.01 0.25,0.167 10 false z17 0.573,0.833 0.802,1 0.229,0.167 10 false *A 1.167,1.198 1.302,1.365 0.135,0.167 10 false 2 2.177,1.208 2.313,1.375 0.135,0.167 10 false 1 0.25,1.115 0.49,1.281 0.24,0.167 10 false z18 0.583,1.135 0.813,1.302 0.229,0.167 10 false *B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Switch Condition Specified Condition
z17-2 (FR+) - Body ground Ignition switch off 10 kΩ or higher
z17-1 (FR-) - Body ground Ignition switch off 10 kΩ or higher

for LH:
Tester Connection Switch Condition Specified Condition
z18-2 (FL+) - Body ground Ignition switch off 10 kΩ or higher
z18-1 (FL-) - Body ground Ignition switch off 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*a Component without harness connected
(Front Speed Sensor)


Result:
Proceed to
OK
NG



OK

7.INSPECT SKID CONTROL SENSOR WIRE

NG

7.INSPECT SKID CONTROL SENSOR WIRE
a.

Remove the skid control sensor wire.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL


b.
U156144E03
0.719,0.927 0.854,0.927 0.854,0.927 0.938,2.219 false 1.417,0.927 1.323,0.927 1.323,0.927 1.219,2.208 false 0.125,0.094 0.375,0.313 0.25,0.219 10 false *1 2.906,1.74 3.167,1.906 0.26,0.167 10 false Az2 3.198,1.604 3.365,1.771 0.167,0.167 10 false *A 3.208,2.031 3.375,2.198 0.167,0.167 10 false *B 2.906,2.146 3.167,2.313 0.26,0.167 10 false Az1 0.125,1.885 0.375,2.052 0.25,0.167 10 false z17 0.406,1.75 0.573,1.917 0.167,0.167 10 false *A 0.406,2.167 0.573,2.333 0.167,0.167 10 false *B 0.125,2.281 0.375,2.448 0.25,0.167 10 false z18 0.177,0.865 0.729,1.323 0.552,0.458 10 false FR-*A, FL-*B 1.51,0.854 2.156,1.375 0.646,0.521 10 false FR+*A, FL+*B

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
Az2-1 - z17-1 (FR-) Always Below 1 Ω
Az2-5 - z17-2 (FR+) Always Below 1 Ω
z17-1 (FR-) - z17-2 (FR+) Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
Az1-1 - z18-1 (FL-) Always Below 1 Ω
Az1-5 - z18-2 (FL+) Always Below 1 Ω
z18-1 (FL-) - z18-2 (FL+) Always 10 kΩ or higher


Text in Illustration
*A for RH
*B for LH
*1 Skid Control Sensor Wire


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Disconnect the A24 skid control ECU connector and z17/z18 front speed sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH:
Tester Connection Condition Specified Condition
A24-3 (FR+) - z17-2 (FR+) Always Below 1 Ω
A24-3 (FR+) - Body ground Always 10 kΩ or higher
A24-17 (FR-) - z17-1 (FR-) Always Below 1 Ω
A24-17 (FR-) - Body ground Always 10 kΩ or higher

for LH:
Tester Connection Condition Specified Condition
A24-18 (FL+) - z18-2 (FL+) Always Below 1 Ω
A24-18 (FL+) - Body ground Always 10 kΩ or higher
A24-4 (FL-) - z18-1 (FL-) Always Below 1 Ω
A24-4 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT MASTER CYLINDER SOLENOID (SKID CONTROL ECU OUTPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT MASTER CYLINDER SOLENOID (SKID CONTROL ECU OUTPUT VOLTAGE)
a.

Reconnect the A24 skid control ECU connector.


b.

Turn the ignition switch to ON.


c.
C173120E06
0.5,1.177 0.938,1.49 0.438,0.313 0.5,0.771 0.938,1.083 0.438,0.313 1.896,1.406 2.51,1.406 true 0.146,0.125 0.375,0.333 0.229,0.208 10 false *a 0.583,0.833 0.896,1.042 0.313,0.208 10 false z17 0.594,1.208 0.906,1.417 0.313,0.208 10 false z18 1,0.771 1.229,0.979 0.229,0.208 10 false *A 0.99,1.208 1.219,1.417 0.229,0.208 10 false *B 2.552,1.198 3.104,1.417 0.552,0.219 10 false FR+*A 2.563,1.406 3.115,1.635 0.552,0.229 10 false FL+*B

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH:
Tester Connection Switch Condition Specified Condition
z17-2 (FR+) - Body ground Ignition switch ON 11 to 14 V

for LH:
Tester Connection Condition Specified Condition
z18-2 (FL+) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*A for RH
*B for LH
*a Front view of wire harness connector
(to Front Speed Sensor)


Result:
Result Proceed to
OK A
NG LHD B
RHD C



A

10.RECONFIRM DTC

B

C

10.RECONFIRM DTC

b.

Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.



HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result:
Result Proceed to
DTC is output. A
DTC is not output. B



A

11.REPLACE FRONT SPEED SENSOR

B

11.REPLACE FRONT SPEED SENSOR
a.

NOTICE:

Check the speed sensor signal after replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).


Result:
Proceed to
NEXT



NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

b.

Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.



HINT:

Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.


Result:
Result Proceed to
DTC is output. A
DTC is not output. B



A

13.INSPECT SPEED SENSOR ROTOR

B

END

13.INSPECT SPEED SENSOR ROTOR
a.

Remove the front axle hub sub-assembly (Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL).


b.

Check the sensor rotor.

OK:

No scratches, oil, or foreign matter on the rotors.


NOTICE:

Check the speed sensor signal after cleaning/replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).



Result:
Result Proceed to
NG A
OK LHD B
RHD C



A

CLEAN OR REPLACE FRONT AXLE HUB SUB-ASSEMBLY (SPEED SENSOR ROTOR)

B

C