Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2015.08
RM2660E _54 Brake _052819 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0255415 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1249  Open in Stop Light Switch Circuit  


DESCRIPTION

The stop light switch signal is input to the skid control ECU and the skid control ECU detects the status of brake operation.

The skid control ECU has an open detection circuit.

If an open in the stop light switch input line or GND side stop light circuit is detected when the stop light switch is off, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
C1249 The ECU terminal IG1 voltage is 9.5 to 17.0 V, ABS is not operating, and an open in the stop light switch circuit continues for 3 seconds or more.
·

Stop light switch circuit

·

Harness or connector

·

Stop light control relay assembly

·

Skid control ECU (Master cylinder solenoid)



WIRING DIAGRAM

C246896E17
5.635,0.542 6.229,0.729 0.594,0.188 10 false STP 5.417,0.531 5.583,0.698 0.167,0.167 10 false 7 5.729,1.844 6.813,2.198 1.083,0.354 10 false Open Detection Circuit 5.396,2.615 5.708,2.865 0.313,0.25 10 false A24 5.396,2.781 7,3.156 1.604,0.375 10 false Skid Control ECU (Master Cylinder Solenoid) 0.625,1.448 1.438,1.625 0.813,0.177 10 false from Battery 0.25,0.667 2.802,0.927 2.552,0.26 10 false from Stop Light Switch Assembly 3.542,1.448 3.802,1.615 0.26,0.167 10 false +B 3.667,1.24 3.99,1.406 0.323,0.167 10 false STP 3.667,2.198 4.042,2.385 0.375,0.188 10 false GND 3.844,0.969 4,1.156 0.156,0.188 10 false 2 3.313,1.292 3.458,1.479 0.146,0.188 10 false 6 3.646,2.5 3.792,2.688 0.146,0.188 10 false 4 3.552,1.875 3.927,2.063 0.375,0.188 10 false OUT 3.313,1.75 3.458,1.938 0.146,0.188 10 false 8 0.719,1.865 2.292,2.323 1.573,0.458 10 false to BRK LP Relay (Brake Light Relay) 4.281,1.188 4.594,1.438 0.313,0.25 10 false A39 4.26,1.365 5.458,1.813 1.198,0.448 10 false Stop Light Control Relay Assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform zero point calibration (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


f.

Check that the stop light switch condition observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON and OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
2.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.



Result:
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

3.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (master cylinder solenoid) connector.


c.
C214161E71
0.219,0.677 0.604,0.917 0.385,0.24 1.688,1.135 2.458,0.677 true 0.26,0.708 0.531,0.875 0.271,0.167 10 false A24 0.125,0.042 2.552,0.396 2.427,0.354 10 false *a 2.51,0.563 2.865,0.74 0.354,0.177 10 false STP

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (+B, GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (+B, GND TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the stop light control relay assembly connector.


c.
U164960E02
1.104,1.469 0.292,1.615 0.292,1.615 0.292,1.698 false 1.771,1.438 2.74,0.677 2.74,0.677 2.833,0.677 false 0.083,0.094 0.271,0.271 0.188,0.177 10 false *a 1.625,0.25 1.917,0.458 0.292,0.208 10 false A39 2.958,0.583 3.198,0.75 0.24,0.167 10 false +B 0.156,1.771 0.521,1.948 0.365,0.177 10 false GND

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A39-6 (+B) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-4 (GND) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to Stop Light Control Relay Assembly)

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

OK

6.CHECK HARNESS AND CONNECTOR (OUT TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (OUT TERMINAL)
a.

Reconnect the stop light control relay assembly connector.


b.
E205929E06
2.719,1.865 3.208,2.198 0.49,0.333 1.167,2.115 0.625,2.115 false 0.125,0.083 2.448,0.427 2.323,0.344 10 false *a 0.229,2.031 0.552,2.198 0.323,0.167 10 false OUT 2.833,1.927 3.125,2.094 0.292,0.167 10 false A39

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-8 (OUT) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Component with harness connected
(Stop Light Control Relay Assembly)


Result:
Proceed to
OK
NG



OK

7.RECONFIRM DTC

NG

REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY

7.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Depress the brake pedal several times to test the stop light circuit.



Result:
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C