Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU) › from 2020.06
RM2660E _57 Power Source / Network _052837 NETWORKING _0255536 CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Central Gateway ECU)  Check Bus 2 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the bus 2 CAN main wires and/or CAN branch wires when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU is below 54 Ω.

Detection Item Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of central gateway ECU is below 54 Ω.
·

Short in bus 2 CAN main wires

·

Short in bus 2 CAN branch wires

·

ECM

·

4WD control ECU

·

Power steering ECU assembly*1

·

Airbag sensor assembly

·

Tire pressure warning ECU*2

·

Air conditioning amplifier assembly

·

Central gateway ECU

·

Main body ECU (multiplex network body ECU)

·

Master cylinder solenoid (skid control ECU)

·

Headlight leveling ECU assembly

·

Certification ECU (smart key ECU assembly)*3

·

Steering control ECU*4

·

Steering sensor

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector



*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System

*3: w/ Entry and Start System

*4: w/ Variable Gear Ratio Steering System


WIRING DIAGRAM

C421620E01
6.177,1.698 6.542,1.844 0.365,0.146 10 false A38 6.177,1.833 6.542,1.979 0.365,0.146 10 false ECM 5.948,1.385 6.448,1.531 0.5,0.146 10 false CANL 5.948,0.667 6.448,0.813 0.5,0.146 10 false CANH 4.823,0.667 5.865,0.813 1.042,0.146 10 false 10*1, 41*2, 11*3 4.823,1.198 5.896,1.344 1.073,0.146 10 false 11*1, 49*2, 19*3 4.083,0.667 4.583,0.813 0.5,0.146 10 false 7 4.083,1.198 4.583,1.344 0.5,0.146 10 false 17 3.198,0.667 3.698,0.813 0.5,0.146 10 false 2 3.125,1.198 3.625,1.344 0.5,0.146 10 false 12 4.083,2.625 4.583,2.771 0.5,0.146 10 false 3 4.083,3.167 4.583,3.313 0.5,0.146 10 false 13 3.198,2.625 3.698,2.771 0.5,0.146 10 false 4 3.125,3.167 3.625,3.313 0.5,0.146 10 false 14 1.396,5.208 1.76,5.354 0.365,0.146 10 false E35 0.094,5.583 1.708,5.927 1.615,0.344 10 false Air Conditioning Amplifier Assembly 0.844,5.219 1.344,5.365 0.5,0.146 10 false CANL 0.844,4.677 1.344,4.823 0.5,0.146 10 false CANH 1.427,4.469 1.927,4.615 0.5,0.146 10 false 3*8 1.438,5.021 1.938,5.167 0.5,0.146 10 false 4*8 4.083,4.583 4.583,4.729 0.5,0.146 10 false 5 4.083,5.125 4.583,5.271 0.5,0.146 10 false 15 3.198,4.583 3.698,4.729 0.5,0.146 10 false 8 3.125,5.125 3.625,5.271 0.5,0.146 10 false 18 2.823,6.052 3.188,6.198 0.365,0.146 10 false E135 2.823,6.198 5.115,6.344 2.292,0.146 10 false No. 1 CAN Junction Connector 0.854,1.313 1.354,1.458 0.5,0.146 10 false CANL 0.854,0.771 1.354,0.917 0.5,0.146 10 false CANH 1.385,0.625 1.885,0.771 0.5,0.146 10 false 20 1.385,1.167 1.885,1.313 0.5,0.146 10 false 40 0.271,1.698 0.635,1.844 0.365,0.146 10 false A27 0.271,1.844 1.99,1.99 1.719,0.146 10 false 4WD Control ECU 0.052,3.573 0.417,3.719 0.365,0.146 10 false E47 0.052,3.708 1.74,4.052 1.688,0.344 10 false Airbag Sensor Assembly 0.854,3.26 1.354,3.406 0.5,0.146 10 false CANL 0.854,2.719 1.354,2.865 0.5,0.146 10 false CANH 1.385,2.573 1.885,2.719 0.5,0.146 10 false 13 1.385,3.115 1.885,3.26 0.5,0.146 10 false 22 6.01,3.25 6.51,3.396 0.5,0.146 10 false CANL 6.01,2.708 6.51,2.854 0.5,0.146 10 false CANH 4.896,3.521 5.313,3.667 0.417,0.146 10 false E102 4.896,3.667 7.073,3.99 2.177,0.323 10 false Power Steering ECU Assembly*4 5.708,3.135 6.208,3.281 0.5,0.146 10 false 2 5.708,2.594 6.208,2.74 0.5,0.146 10 false 1 5.115,4.667 5.479,4.813 0.365,0.146 10 false L65 5.115,5.198 5.479,5.344 0.365,0.146 10 false L65 5.563,4.667 5.927,4.813 0.365,0.146 10 false L75 5.563,5.198 5.927,5.344 0.365,0.146 10 false L75 5.958,5.208 6.458,5.354 0.5,0.146 10 false CANL 5.958,4.677 6.458,4.823 0.5,0.146 10 false CANH 5.083,5.01 5.583,5.156 0.5,0.146 10 false 10*5 5.115,4.469 5.615,4.615 0.5,0.146 10 false 9*5 5.552,5.01 6.052,5.156 0.5,0.146 10 false 10*6 5.573,4.469 6.073,4.615 0.5,0.146 10 false 9*6 5.052,5.615 7.021,5.76 1.969,0.146 10 false Tire Pressure Warning ECU*7 0.198,6.333 1.979,6.479 1.781,0.146 10 false *1: for 1UR-FE, 1GR-FE 0.198,6.885 1.458,7.031 1.26,0.146 10 false *3: for 3UR-FE 0.198,6.615 1.708,6.76 1.51,0.146 10 false *2: for 1VD-FTV 0.198,7.167 3.531,7.313 3.333,0.146 10 false *4: w/ Variable Flow Control Solenoid Valve 0.208,7.458 2.667,7.604 2.458,0.146 10 false *5: w/o Front Antenna 3.24,6.594 5.75,6.802 2.51,0.208 10 false *6: w/ Front Antenna 3.24,6.875 6.25,7.083 3.01,0.208 10 false *7: w/ Tire Pressure Warning System 1.417,4.656 1.781,4.802 0.365,0.146 10 false E35 1.865,4.667 2.229,4.813 0.365,0.146 10 false E81 1.865,5.208 2.229,5.354 0.365,0.146 10 false E81 1.844,4.469 2.344,4.615 0.5,0.146 10 false 11*9 1.854,5.021 2.354,5.167 0.5,0.146 10 false 12*9 3.24,7.167 6.208,7.344 2.969,0.177 10 false *8: for Automatic Air Conditioning System 3.24,7.448 6.26,7.625 3.021,0.177 10 false *9: for Manual Air Conditioning System

C348516E02
4.125,2.427 4.625,2.573 0.5,0.146 10 false 1 4.125,2.969 4.625,3.115 0.5,0.146 10 false 11 4.125,0.469 4.625,0.615 0.5,0.146 10 false 1 4.125,1 4.625,1.146 0.5,0.146 10 false 11 3.167,2.427 3.667,2.573 0.5,0.146 10 false 2 3.104,2.969 3.604,3.115 0.5,0.146 10 false 12 3.167,0.469 3.667,0.615 0.5,0.146 10 false 9 3.104,1 3.604,1.146 0.5,0.146 10 false 19 4.125,4.396 4.625,4.542 0.5,0.146 10 false 3 4.125,4.927 4.625,5.073 0.5,0.146 10 false 13 3.167,4.396 3.667,4.542 0.5,0.146 10 false 4 3.104,4.927 3.604,5.073 0.5,0.146 10 false 14 3.177,6.365 3.677,6.51 0.5,0.146 10 false 8 3.115,6.906 3.615,7.052 0.5,0.146 10 false 18 4.125,6.365 4.625,6.51 0.5,0.146 10 false 6 4.125,6.906 4.625,7.052 0.5,0.146 10 false 16 2.771,7.646 3.135,7.792 0.365,0.146 10 false E133 2.771,7.781 4.719,7.927 1.948,0.146 10 false No. 2 CAN Junction Connector 2.729,1.448 3.094,1.594 0.365,0.146 10 false E135 2.729,1.583 5.135,1.729 2.406,0.146 10 false No. 1 CAN Junction Connector 0.885,1.125 1.385,1.271 0.5,0.146 10 false CA4L 0.885,0.583 1.385,0.729 0.5,0.146 10 false CA4H 1.396,1.042 1.896,1.188 0.5,0.146 10 false 17 1.396,0.51 1.896,0.656 0.5,0.146 10 false 18 0.344,1.521 0.708,1.667 0.365,0.146 10 false E145 0.344,1.656 2.188,1.802 1.844,0.146 10 false Central Gateway ECU 0.865,3.052 1.365,3.198 0.5,0.146 10 false CANL 0.865,2.5 1.365,2.646 0.5,0.146 10 false CANH 1.375,2.969 1.875,3.115 0.5,0.146 10 false 13 1.375,2.438 1.875,2.583 0.5,0.146 10 false 14 0.25,3.438 0.771,3.583 0.521,0.146 10 false E118 0.25,3.604 1.917,4.104 1.667,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 5.479,5.313 5.844,5.458 0.365,0.146 10 false A24 5.479,5.448 7.125,5.792 1.646,0.344 10 false Master Cylinder Solenoid (Skid Control ECU) 5.99,5.031 6.49,5.177 0.5,0.146 10 false CANL 5.99,4.49 6.49,4.635 0.5,0.146 10 false CANH 5.719,4.406 6.219,4.552 0.5,0.146 10 false 11 5.719,4.938 6.219,5.083 0.5,0.146 10 false 25 0.865,5.042 1.365,5.188 0.5,0.146 10 false CANL 0.865,4.5 1.365,4.646 0.5,0.146 10 false CANH 1.438,4.844 1.938,4.99 0.5,0.146 10 false 13*1 1.438,4.313 1.938,4.458 0.5,0.146 10 false 12*1 1.396,5.031 1.896,5.177 0.5,0.146 10 false E101 1.396,5.031 1.896,5.177 0.5,0.146 10 false E101 1.396,4.5 1.896,4.646 0.5,0.146 10 false E101 1.896,4.844 2.396,4.99 0.5,0.146 10 false 7*2 1.896,4.313 2.396,4.458 0.5,0.146 10 false 6*2 1.854,5.031 2.354,5.177 0.5,0.146 10 false E109 1.854,4.5 2.354,4.646 0.5,0.146 10 false E109 0.302,5.417 2.76,5.563 2.458,0.146 10 false Headlight Leveling ECU Assembly 5.604,7.375 5.969,7.521 0.365,0.146 10 false E130 5.604,7.51 7.146,7.854 1.542,0.344 10 false Certification ECU (Smart Key ECU Assembly)*3 5.99,6.99 6.49,7.135 0.5,0.146 10 false CANL 5.99,6.448 6.49,6.594 0.5,0.146 10 false CANH 5.802,6.365 6.302,6.51 0.5,0.146 10 false 7 5.802,6.896 6.302,7.042 0.5,0.146 10 false 8 0.917,7.01 1.417,7.156 0.5,0.146 10 false CNL1 0.917,6.469 1.417,6.615 0.5,0.146 10 false CNH1 1.385,6.885 1.885,7.031 0.5,0.146 10 false 9 1.385,6.354 1.885,6.5 0.5,0.146 10 false 3 0.354,7.396 0.719,7.542 0.365,0.146 10 false E161 0.354,7.542 2.458,7.688 2.104,0.146 10 false Steering Control ECU*4 2.854,8.24 4.958,8.385 2.104,0.146 10 false *3: w/ Entry and Start System 0.208,8.542 2.563,8.688 2.354,0.146 10 false *2: w/o Automatic High Beam System 0.208,8.24 2.51,8.385 2.302,0.146 10 false *1: w/ Automatic High Beam System 2.854,8.542 5.719,8.688 2.865,0.146 10 false *4: w/ Variable Gear Ratio Steering System

C334635E04
3.073,1.094 3.573,1.24 0.5,0.146 10 false 10 3.073,1.625 3.573,1.771 0.5,0.146 10 false 20 5.177,2.031 5.615,2.177 0.438,0.146 10 false E119 5.177,2.198 7.125,2.542 1.948,0.344 10 false Combination Meter Assembly 5.917,1.854 6.417,2 0.5,0.146 10 false CANL 5.917,1.104 6.417,1.25 0.5,0.146 10 false CANH 5.635,1.104 6.135,1.25 0.5,0.146 10 false 39 5.656,1.635 6.156,1.781 0.5,0.146 10 false 40 4.052,1.073 4.552,1.219 0.5,0.146 10 false 7 4.052,1.604 4.552,1.75 0.5,0.146 10 false 17 2.792,2.198 4.875,2.448 2.083,0.25 10 false No. 2 CAN Junction Connector 2.792,2.031 3.229,2.177 0.438,0.146 10 false E133 0.802,1.719 1.302,1.865 0.5,0.146 10 false CANL 0.802,1.177 1.302,1.323 0.5,0.146 10 false CANH 1.417,1.521 1.917,1.667 0.5,0.146 10 false 3*1 1.406,0.99 1.906,1.135 0.5,0.146 10 false 4*1 1.865,1.521 2.365,1.667 0.5,0.146 10 false 2*2 1.854,0.99 2.354,1.135 0.5,0.146 10 false 3*2 2.302,1.521 2.802,1.667 0.5,0.146 10 false 2*3 2.292,0.99 2.792,1.135 0.5,0.146 10 false 3*3 0.406,2.146 1.99,2.51 1.583,0.365 10 false Steering Sensor 1.344,1.198 1.708,1.344 0.365,0.146 10 false E181 1.344,1.729 1.708,1.875 0.365,0.146 10 false E181 1.792,1.198 2.156,1.344 0.365,0.146 10 false E121 1.792,1.729 2.156,1.875 0.365,0.146 10 false E121 2.24,1.198 2.604,1.344 0.365,0.146 10 false E163 2.24,1.729 2.604,1.875 0.365,0.146 10 false E163 0.24,3.219 5.396,3.365 5.156,0.146 10 false *1: w/o Variable Gear Ratio Steering System, w/o Entry and Start System 0.24,3.698 5.396,3.844 5.156,0.146 10 false *2: w/o Variable Gear Ratio Steering System, w/ Entry and Start System 0.24,4.177 3.208,4.323 2.969,0.146 10 false *3: w/ Variable Gear Ratio Steering System

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.
U166177E02
2.406,1.177 2.625,1.063 2.625,1.063 2.667,1.063 false 1.865,0.448 1.948,0.448 1.948,0.448 2.323,0.802 false 2.031,1.833 2.115,1.833 2.115,1.833 2.396,1.313 false 2.01,0.219 2.094,0.219 2.094,0.219 2.396,0.792 false 2.406,0.896 2.583,0.469 2.583,0.469 2.667,0.469 false 0.323,1.021 0.74,1.219 0.417,0.198 10 false A38 0.094,0.063 0.427,0.302 0.333,0.24 10 false *a 1.219,0.354 1.948,0.521 0.729,0.167 10 false CANH*A 0.781,0.125 2.25,0.302 1.469,0.177 10 false CANL*A, CANH*C 2.698,0.979 3.385,1.167 0.688,0.188 10 false CANH*B 2.698,0.375 3.365,0.573 0.667,0.198 10 false CANL*C 1.375,1.75 2.094,1.938 0.719,0.188 10 false CANL*B

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1UR-FE, 1GR-FE:
Tester Connection Condition Specified Condition
A38-10 (CANH) - A38-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1VD-FTV:
Tester Connection Condition Specified Condition
A38-41 (CANH) - A38-49 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 3UR-FE:
Tester Connection Condition Specified Condition
A38-11 (CANH) - A38-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*A for 1UR-FE
*B for 1VD-FTV
*C for 3UR-FE
*a Front view of wire harness connector
(to ECM)

Result
Result Proceed to
OK (for 1UR-FE) A
OK (for 1VD-FTV) B
OK (for 1GR-FE) C
OK (for 3UR-FE) D
NG E



A

B

C

D

E

2.CONNECT CONNECTOR
2.CONNECT CONNECTOR
a.

Reconnect the A38 ECM connector.



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
a.
U165131E01
1.539,0.276 1.951,0.414 0.412,0.137 10 E119 0.252,1.752 0.671,1.889 0.419,0.137 10 CANH 0.14,1.372 0.550,1.510 0.409,0.137 10 CANL 0.074,0.061 0.262,0.198 0.188,0.137 10 *a 0.978,1.264 0.752,1.454 0.752,1.454 0.624,1.454 false 1.061,1.264 0.939,1.845 0.939,1.845 0.76,1.845 false

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-39 (CANH) - E119-40 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter Assembly)



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CONNECT CONNECTOR
4.CONNECT CONNECTOR
a.

Reconnect the E119 combination meter assembly connector.



NEXT

5.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU - NO. 1 CAN JUNCTION CONNECTOR)
a.
U165594E01
0.071,0.041 0.241,0.194 0.170,0.153 10 *a 1.505,0.138 1.852,0.277 0.347,0.139 10 E145 2.384,1.67 3.026,1.821 0.642,0.151 10 CA4H 2.032,1.888 2.674,2.039 0.642,0.151 10 CA4L 1.78,1.197 2.245,1.773 2.245,1.773 2.359,1.773 false 2.014,1.971 1.825,1.971 1.825,1.971 1.646,1.197 false

Disconnect the central gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-18 (CA4H) - E145-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Central Gateway ECU)



OK

NG

6.CONNECT CONNECTOR
6.CONNECT CONNECTOR
a.

Reconnect the E145 central gateway ECU connector.



NEXT

7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

U165477E01
0.123,0.087 0.348,0.257 0.225,0.170 10 *a 0.932,0.84 1.275,0.982 0.343,0.142 10 E135 1.676,0.519 2.245,0.662 0.569,0.144 10 CANH*b 1.711,1.133 2.280,1.277 0.569,0.144 10 CANL*b 1.898,1.317 2.468,1.460 0.569,0.144 10 CANL*c 2.454,1.386 2.646,1.386 2.646,1.386 2.834,0.999 false 2.063,1.573 2.632,1.716 0.569,0.144 10 CANL*d 3.128,1.564 3.697,1.707 0.569,0.144 10 CANL*e 2.073,0.195 2.643,0.338 0.569,0.144 10 CANH*d 1.814,0.352 2.384,0.496 0.569,0.144 10 CANH*c 2.343,0.03 2.913,0.174 0.569,0.144 10 CANH*e 4.737,0.41 5.307,0.554 0.569,0.144 10 CANH*h 3.924,0.053 4.494,0.197 0.569,0.144 10 CANH*f 4.366,0.235 4.935,0.379 0.569,0.144 10 CANH*g 4.537,1.253 5.107,1.396 0.569,0.144 10 CANL*h 4.373,1.417 4.942,1.561 0.569,0.144 10 CANL*g 3.956,1.596 4.525,1.740 0.569,0.144 10 CANL*f 4.172,0.839 4.617,0.469 4.617,0.469 4.715,0.469 false 4.947,0.62 5.517,0.764 0.569,0.144 10 CANH*i 4.368,0.867 4.827,0.679 4.827,0.679 4.925,0.679 false 3.471,0.844 3.813,0.117 3.813,0.117 3.911,0.117 false 2.609,0.839 2.364,0.595 2.364,0.595 2.266,0.595 false 2.412,0.418 2.604,0.418 2.604,0.418 2.834,0.847 false 2.629,0.271 2.87,0.271 2.87,0.271 3.044,0.836 false 2.916,0.096 3.158,0.096 3.158,0.096 3.235,0.831 false 3.981,0.841 4.14,0.308 4.14,0.308 4.354,0.308 false 4.186,1.021 4.421,1.308 4.421,1.308 4.519,1.308 false 4.818,1.085 5.387,1.228 0.569,0.144 10 CANL*i 4.368,1.021 4.701,1.139 4.701,1.139 4.799,1.139 false 3.485,1.017 3.827,1.667 3.827,1.667 3.925,1.667 false 2.609,1.007 2.364,1.198 2.364,1.198 2.266,1.198 false 2.454,1.386 2.646,1.386 2.646,1.386 2.834,0.999 false 2.599,1.633 2.841,1.633 2.841,1.633 3.044,1.024 false 3.114,1.628 2.988,1.628 2.988,1.628 3.235,1.029 false 3.981,1.02 4.126,1.483 4.126,1.483 4.34,1.483 false

Text in Illustration
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to 4WD Control ECU *d to Power Steering ECU Assembly (w/ Variable Flow Control Solenoid Valve)
*e to Airbag Sensor Assembly *f to Tire Pressure Warning ECU (w/ Tire Pressure Warning System)
*g to ECM *h to Air Conditioning Amplifier Assembly
*i to Central Gateway ECU - -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E135-1 (CANH) - E135-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
E135-2 (CANH) - E135-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4WD control ECU
E135-3 (CANH) - E135-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly*1
E135-4 (CANH) - E135-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
E135-5 (CANH) - E135-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Tire pressure warning ECU*2
E135-7 (CANH) - E135-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
E135-8 (CANH) - E135-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
E135-9 (CANH) - E135-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU


*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System


Result
Result Proceed to
OK A
NG (ECM CAN main wire) B
NG (Central gateway ECU CAN branch wire) C
NG (No. 2 CAN junction connector CAN main wire) D
NG (ECU or sensor CAN branch wires) E



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - ECM)

C

REPAIR OR REPLACE CAN BRANCH WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU)

D

8.CONNECT CONNECTOR

E

10.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
8.CONNECT CONNECTOR
a.

Reconnect the E135 No. 1 CAN junction connector.



NEXT

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)
9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.

U165478E01
0.123,0.083 0.348,0.253 0.225,0.170 10 *a 0.511,0.836 0.855,0.978 0.343,0.142 10 E133 1.55,0.641 2.119,0.785 0.569,0.144 10 CANH*b 1.571,1.003 2.140,1.147 0.569,0.144 10 CANL*b 1.716,1.187 2.286,1.331 0.569,0.144 10 CANL*c 2.271,1.257 2.394,1.257 2.394,1.257 2.792,1.009 false 1.839,1.359 2.408,1.502 0.569,0.144 10 CANL*d 1.923,1.518 2.492,1.661 0.569,0.144 10 CANL*e 1.807,0.317 2.377,0.461 0.569,0.144 10 CANH*d 1.674,0.475 2.244,0.618 0.569,0.144 10 CANH*c 1.937,0.181 2.506,0.324 0.569,0.144 10 CANH*e 4.893,0.627 5.463,0.770 0.569,0.144 10 CANH*i 4.404,0.217 5.132,0.394 0.727,0.177 10 CANH*g 4.66,0.399 5.229,0.543 0.569,0.144 10 CANH*h 4.945,1.073 5.515,1.217 0.569,0.144 10 CANL*i 4.597,1.21 5.166,1.354 0.569,0.144 10 CANL*h 4.467,1.403 5.243,1.567 0.776,0.164 10 CANL*g 4.13,0.836 4.524,0.451 4.524,0.451 4.622,0.451 false 3.737,0.84 4.034,0.127 4.034,0.127 4.132,0.127 false 2.271,0.54 2.38,0.54 2.38,0.54 2.806,0.844 false 2.363,0.393 2.492,0.393 2.492,0.393 3,0.847 false 3.939,0.823 4.154,0.297 4.154,0.297 4.368,0.297 false 4.13,1.003 4.471,1.275 4.471,1.275 4.569,1.275 false 3.737,0.999 3.967,1.677 3.967,1.677 4.065,1.677 false 4.557,0.836 4.773,0.679 4.773,0.679 4.871,0.679 false 4.557,1.017 4.802,1.146 4.802,1.146 4.9,1.146 false 2.623,0.85 2.238,0.717 2.238,0.717 2.14,0.717 false 2.609,1.003 2.224,1.068 2.224,1.068 2.126,1.068 false 2.271,1.257 2.394,1.257 2.394,1.257 2.792,1.009 false 2.389,1.433 2.518,1.433 2.518,1.433 3.014,1.006 false 3.939,1.016 4.231,1.465 4.231,1.465 4.445,1.465 false 2.493,0.259 2.622,0.259 2.622,0.259 3.186,0.839 false 2.462,1.598 2.592,1.598 2.592,1.598 3.171,1.016 false 4.094,1.614 4.664,1.758 0.569,0.144 10 CANL*f 4.164,0.076 4.734,0.219 0.569,0.144 10 CANH*f

Text in Illustration
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 1 CAN Junction Connector
*c to Main Body ECU (Multiplex Network Body ECU) *d to Master Cylinder Solenoid (Skid Control ECU)
*e to Headlight Leveling ECU Assembly *f to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System)
*g to Combination Meter Assembly *h to Steering Control ECU (w/ Variable Gear Ratio Steering System)
*i to Steering Sensor - -


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connect to
E133-1 (CANH) - E133-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector
E133-2 (CANH) - E133-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
E133-3 (CANH) - E133-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Master cylinder solenoid (skid control ECU)
E133-4 (CANH) - E133-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Headlight leveling ECU assembly
E133-6 (CANH) - E133-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*1
E133-7 (CANH) - E133-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
E133-8 (CANH) - E133-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering control ECU*2
E133-10 (CANH) - E133-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor


*1: w/ Entry and Start System

*2: w/ Variable Gear Ratio Steering System


Result
Result Proceed to
OK A
NG (Combination meter assembly CAN main wire) B
NG (No. 1 CAN junction connector CAN main wire) C
NG (ECU or sensor CAN branch wires) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

D

10.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
10.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
U165586E02
1.76,1.104 2.26,1.646 2.26,1.646 2.385,1.646 false 1.677,1.104 1.917,1.917 1.917,1.917 2.031,1.917 false 1.563,0.302 2.135,0.531 0.573,0.229 10 false E145 0.115,0.073 0.448,0.281 0.333,0.208 10 false *a 2.063,1.823 2.729,2.042 0.667,0.219 10 false CA4H 2.417,1.563 3.083,1.781 0.667,0.219 10 false CA4L

Reconnect the CAN junction connector.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch wire is connected.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E145-18 (CA4H) - E145-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


Text in Illustration
*a Component with harness connected
(Central Gateway ECU)

HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.




OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR CAN BRANCH WIRES OR CONNECTOR