Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE PEDAL STROKE SENSOR (for LHD) › 2021.04–2021.07
RM38G0E _54 Brake _100463 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0467255 BRAKE PEDAL STROKE SENSOR(for LHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE PEDAL STROKE SENSOR(for LHD)  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
C455198N01
5.948,2.208 6.958,2.396 1.01,0.188 5.917,2.177 7,2.427 1.083,0.25 6.5,0.24 6.833,0.24 false 6.5,0.677 6.833,0.677 false 5.688,2.615 5.771,2.292 5.771,2.292 5.938,2.292 false 5.375,2.99 5.875,2.99 false 5.948,0.083 6.615,0.5 0.667,0.417 18 false 1, 4 6.24,0.521 6.573,0.938 0.333,0.417 18 false 3 6.167,2.854 6.833,3.271 0.667,0.417 18 false 2 5.771,2.615 6.104,2.865 0.333,0.25 10 false x 2 6,2.219 7.01,2.469 1.01,0.25 8 false 8.5 (87, 75 in.*lbf)

Procedure Part Name Code
Z101186

Z101188

Z101187

1 INSPECT AND ADJUST BRAKE PEDAL HEIGHT - - - (Click here)
2 INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D (Click here) - -
3 CONNECT CABLE TO NEGATIVE BATTERY TERMINAL - - - -
4 ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY 89510D - - (Click here)

V111893

Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) - -

C457228N01
6.396,0.635 6.813,0.635 false 4.771,1.552 4.938,1.552 4.938,1.552 5.188,1.365 false 3.083,1.479 3.25,1.479 3.25,1.479 3.5,1.292 false 1.125,0.865 1.292,0.865 1.292,0.865 1.531,0.521 false 6.417,0.229 6.833,0.229 false 5.719,0.479 6.469,0.896 0.75,0.417 18 false 8, 10 2.823,1.323 3.073,1.656 0.25,0.333 18 false 5 6.115,0.073 6.531,0.49 0.417,0.417 18 false 9 2.135,0.813 2.385,1.146 0.25,0.333 10 false x 2 4.51,1.385 4.76,1.677 0.25,0.292 18 false 7 0.875,0.708 1.125,1.042 0.25,0.333 18 false 6

Procedure Part Name Code
Z101186

Z101188

Z101187

5 COWL SIDE TRIM BOARD LH 62112 - - -
6 NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY 55606 - - -
7 FRONT DOOR SCUFF PLATE LH 67914B - - -
8 PERFORM CALIBRATION - - - (Click here)
9 CHECK AND CLEAR DTC - - - -
10 INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL - - - (Click here)

CAUTION / NOTICE / HINT

PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

Hide 89510D 2.INSTALL BRAKE PEDAL STROKE SENSOR ASSEMBLY

a.

When installing a new brake pedal stroke sensor assembly:

C455202C02
2.875,0.458 3.052,0.271 true 2.813,0.875 2.979,0.604 true 4.052,0.698 4.229,0.594 true 2.635,0.813 2.813,0.99 0.177,0.177 10 true *a 3.073,0.146 3.229,0.313 0.156,0.167 10 true *b 3.875,0.656 4.042,0.844 0.167,0.188 10 true *c 2.552,0.052 2.688,0.302 0.135,0.25 18 true i 4.5,1.302 4.656,1.563 0.156,0.26 18 true ii 4.49,2.375 4.646,2.635 0.156,0.26 18 true ii 2.896,2.125 3.115,2.396 0.219,0.271 18 true iii 3.896,0.052 4.104,0.313 0.208,0.26 18 true iv
*a Brake Pedal Stroke Sensor Assembly Lever *b Brake Pedal Groove
*c Brake Pedal Stroke Sensor Assembly Lever Set Pin - -


i.

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.

NOTICE:

Do not break the brake pedal stroke sensor assembly lever set pin before installing the brake pedal stroke sensor assembly with the 2 nuts.



ii.

Install a new brake pedal stroke sensor assembly to the brake pedal support assembly with the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:
·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.




iii.

Connect the connector.


iv.

Firmly depress the brake pedal to break the brake pedal stroke sensor assembly lever set pin and remove the broken lever set pin.



b.

When reusing the brake pedal stroke sensor assembly:

C455204C01
2.198,0.896 2.427,0.677 true 2.302,0.542 2.458,0.406 true 2.021,0.896 2.208,1.073 0.188,0.177 10 true *a 2.51,0.302 2.667,0.49 0.156,0.188 10 true *b 2,0.135 2.135,0.406 0.135,0.271 18 true i 5.208,0.365 5.375,0.625 0.167,0.26 18 true ii 5.229,1.354 5.396,1.615 0.167,0.26 18 true ii 3.99,1.302 4.198,1.583 0.208,0.281 18 true iii
*a Brake Pedal Stroke Sensor Assembly Lever *b Brake Pedal Groove


i.

Engage the brake pedal stroke sensor assembly lever with the brake pedal groove.


ii.

Install the brake pedal stroke sensor assembly to the brake pedal support assembly and tighten the 2 nuts.

NOTICE:
·

Check that there is no foreign matter attached to the contact surface of the brake pedal stroke sensor assembly.

·

Check that the tip of the brake pedal stroke sensor assembly lever is protruding from the brake pedal groove.

·

Do not drop the brake pedal stroke sensor assembly.

·

If the brake pedal stroke sensor assembly has been dropped, replace the brake pedal stroke sensor assembly with a new one.



HINT:

The nuts will be fully tightened when adjusting the brake pedal stroke sensor assembly.



iii.

Connect the connector.



Hide 3.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 89510D 4.ADJUST BRAKE PEDAL STROKE SENSOR ASSEMBLY

Z101186

NOTICE:

When the brake pedal stroke sensor assembly is being reused, perform the following procedure to adjust it.



a.
C441118N01
0.417,0.063 0.698,0.417 0.281,0.354 18 false i

i.

Read the stroke sensor value in the Data List.

Chassis > Brake Booster > Data List
Tester Display
Stroke Sensor
50003 466 207


b.
C455206N01
4.635,0.833 4.792,1.083 0.156,0.25 18 true i 4.615,0.313 4.792,0.594 0.177,0.281 18 true ii 4.625,1.344 4.802,1.625 0.177,0.281 18 true ii

i.

Turn the brake pedal stroke sensor assembly slowly to the right or left to adjust the output voltage so that it is within the following range.

Standard Voltage (without the brake pedal depressed):

0.8 to 1.2 V



ii.

Tighten the 2 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

NOTICE:

Do not depress the brake pedal after turning the ignition switch to ON.




Hide 62112 5.INSTALL COWL SIDE TRIM BOARD LH

Hide 55606 6.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 67914B 7.INSTALL FRONT DOOR SCUFF PLATE LH

Hide 9. CHECK AND CLEAR DTC

Hide 10. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART