Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP
RM38G0E _54 Brake _100464 BRAKE SYSTEM (OTHER) _0467269 BRAKE BOOSTER PUMP A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP  REMOVAL  


CAUTION / NOTICE / HINT

COMPONENTS (REMOVAL)
C452253N01
3.958,2.167 4.625,2.167 false 4.698,2.01 5.031,2.51 0.333,0.5 18 false 1

Procedure Part Name Code
Z101186

Z101188

Z101187

1 BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY 47210L - - -

C452255N01
4.521,4.844 4.521,5.24 4.521,5.24 4.771,5.24 false 2.896,4.188 2.896,4.583 2.896,4.583 3.146,4.583 false 5.844,2.729 5.844,3.313 5.844,3.313 6.01,3.313 false 0.875,2.604 0.875,2.25 0.875,2.25 1.125,2.25 false 1.073,3.281 1.333,3.281 1.333,3.281 1.333,2.948 false 5.125,5.104 5.542,5.521 0.417,0.417 18 false 3 3.229,4.417 3.646,4.833 0.417,0.417 18 false 2 6.354,3.198 6.688,3.531 0.333,0.333 18 false 4 0.865,3.188 1.198,3.521 0.333,0.333 10 false *2 1.188,2.146 1.521,2.479 0.333,0.333 10 false *1

Procedure Part Name Code
Z101186

Z101188

Z101187

2 NO. 2 RESERVOIR HOSE - - - -
3 NO. 1 BRAKE ACTUATOR TUBE - (Click here) - -
4 BRAKE BOOSTER PUMP WITH ACCUMULATOR ASSEMBLY 47070B (Click here) - -

*1 BRAKE ACTUATOR CASE COLLAR *2 BRAKE BOOSTER PUMP BUSHING

C452259N01
4.792,2.531 4.885,3.083 4.885,3.083 5.052,3.073 false 3.01,2.781 3.427,2.781 false 1.292,1.115 1.458,1.115 1.458,1.115 1.635,1.365 false 5.375,2.938 5.708,3.271 0.333,0.333 18 false 7 2.771,2.646 3.104,2.979 0.333,0.333 18 false 6 1.063,0.958 1.396,1.292 0.333,0.333 18 false 5 6.281,2.74 6.615,3.073 0.333,0.333 10 false x 2 3.594,3.375 3.927,3.625 0.333,0.25 10 false x 2

Procedure Part Name Code
Z101186

Z101188

Z101187

5 NO. 2 WIRE CLAMP BRACKET - (Click here) - -
6 NO. 1 BRAKE POWER SUPPLY BRACKET - (Click here) - -
7 NO. 2 BRAKE POWER SUPPLY BRACKET - (Click here) - -

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster pump with accumulator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedures Necessary procedures Effect/Inoperative Function when Necessary Procedures are not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:
·

When the cable is disconnected/reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)
Lighting system (EXT) Cornering lights Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Lane tracing assist system
Lane departure alert system
Adaptive high beam system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system After the ignition switch is turned to ON, the servo motor and expansion valve standard position is recognized. -




CAUTION / NOTICE / HINT

NOTICE:
·

While the battery is connected, even if the ignition switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.

·
C452240C10
2.25,0.667 2.25,0.417 2.25,0.417 2.5,0.417 false 2.354,1.74 2.521,1.74 false 2.188,1.5 2.604,1.417 2.604,1.417 2.854,1.417 true 0.719,0.521 0.969,0.521 false 0.771,1.448 1.104,1.448 false 0.729,1.01 1.063,1.01 false 1.854,0.917 2.021,0.167 2.021,0.167 2.188,0.167 true 0.938,1.833 1.271,1.833 false 2.542,0.354 2.792,0.521 0.25,0.167 10 false *a 0.521,0.927 0.771,1.094 0.25,0.167 10 false *b 2.573,1.656 2.823,1.906 0.25,0.25 10 false *c 2.896,1.375 3.229,1.708 0.333,0.333 10 false *d 0.49,0.427 0.74,0.677 0.25,0.25 10 false *e 0.583,1.354 0.917,1.604 0.333,0.25 10 false *f 2.25,0.073 2.5,0.323 0.25,0.25 10 false *g 0.74,1.771 1.073,2.021 0.333,0.25 10 false *h
*a No. 1 Skid Control ECU
*b No. 1 Reservoir Hose and No. 2 Reservoir Hose
*c Master Cylinder Push Rod Clevis
*d Boot
*e Brake Master Cylinder Reservoir
*f No. 1 Brake Actuator Tube
*g No. 1 Wire Clamp Bracket
*h Brake Booster Pump with Accumulator Assembly


Do not carry the brake master cylinder with pump assembly by the parts shown in the illustration.



PROCEDURE

Hide 47210L 1.REMOVE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

Hide 2.DISCONNECT NO. 2 RESERVOIR HOSE

a.
C452261


Hide 3.REMOVE NO. 1 BRAKE ACTUATOR TUBE

a.
C452263N01
0.396,0.073 0.677,0.427 0.281,0.354 18 false i

i.

Using a union nut wrench, remove the No. 1 brake actuator tube.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.





Hide 47070B 4.REMOVE BRAKE BOOSTER PUMP WITH ACCUMULATOR ASSEMBLY

Z101186

NOTICE:
·

Do not drop the brake booster pump assembly when carrying it.

·

Be careful not to allow brake fluid to enter the connector.




a.
C457217N01
0.115,0.063 0.396,0.417 0.281,0.354 18 false i 4.042,0.063 4.323,0.417 0.281,0.354 18 false ii

i.

Disengage the 3 clamps to separate the wire harness.


ii.

Remove the nut, brake booster pump with accumulator assembly, brake booster pump bushing and No. 1 brake actuator case collar.



Hide 5.REMOVE NO. 2 WIRE CLAMP BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 2 wire clamp bracket is necessary.



a.

for LHD:

C452267N02
0.385,0.073 0.719,0.406 0.333,0.333 18 false i

i.

Using a 5 mm long hexagon socket wrench, remove the bolt and No. 2 wire clamp bracket.



Hide 6.REMOVE NO. 1 BRAKE POWER SUPPLY BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 1 brake power supply bracket is necessary.



a.
C452269N01
0.375,0.073 0.958,0.406 0.583,0.333 18 false i

i.

Using a 5 mm long hexagon socket wrench, remove the 2 bolts and No. 1 brake power supply bracket.



Hide 7.REMOVE NO. 2 BRAKE POWER SUPPLY BRACKET

Z101186

HINT:

Perform this procedure only when replacement of the No. 2 brake power supply bracket is necessary.



a.
C452271N01
0.375,0.073 0.792,0.406 0.417,0.333 18 false i

i.

Using a 5 mm long hexagon socket wrench, remove the 2 bolts and No. 2 brake power supply bracket.