Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › CAMSHAFT POSITION SENSOR
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0467384 CAMSHAFT POSITION SENSOR A

1GR-FE ENGINE CONTROL  CAMSHAFT POSITION SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A516021N01
6.021,0.969 6.667,1.167 0.646,0.198 5.135,0.76 5.833,0.969 0.698,0.208 3.896,1.031 4.542,1.208 0.646,0.177 1.854,1.031 2.5,1.208 0.646,0.177 3.729,1.104 3.896,1.104 true 4.427,0.542 4.917,0.542 true 6.052,2.208 6.052,1.771 6.052,1.771 5.781,1.771 true 5.125,0.865 4.792,0.865 4.792,0.865 4.792,1.51 true 6.01,1.063 5.625,1.063 5.625,1.063 5.625,1.375 true 6.313,0.26 6.802,0.26 true 4.479,2.146 4.479,2.344 4.479,2.344 4.688,2.344 true 3.281,1.635 3.729,1.635 true 2.5,1.115 2.875,1.115 2.875,1.115 2.875,1.385 true 1.667,1.781 2.198,1.781 true 2.042,2.063 2.365,2.063 true 3.417,1.99 3.646,1.99 true 4.042,2.156 4.271,2.156 true 5.375,1.948 5.604,1.948 true 4.99,2.219 5.271,2.573 0.281,0.354 18 false 2 6.219,2.208 6.5,2.563 0.281,0.354 18 false 1 6.135,0.135 6.417,0.49 0.281,0.354 18 false 6 6.073,0.99 6.75,1.177 0.677,0.188 8 false 10 (102, 7) 5.198,0.781 5.875,0.969 0.677,0.188 8 false 10 (102, 7) 2.344,1.969 2.563,2.24 0.219,0.271 10 false ● 3.958,2.063 4.177,2.333 0.219,0.271 10 false ● 2.938,3.729 3.156,4 0.219,0.271 10 false ● 4.979,0.427 5.26,0.781 0.281,0.354 18 false 5 4.021,1.5 4.302,1.854 0.281,0.354 18 false 3 3.958,1.042 4.635,1.229 0.677,0.188 8 false 10 (102, 7) 1.906,1.052 2.583,1.24 0.677,0.188 8 false 10 (102, 7) 1.427,1.646 1.708,2 0.281,0.354 18 false 4 5.313,1.854 5.531,2.125 0.219,0.271 10 false ● 3.646,1.896 3.865,2.167 0.219,0.271 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 VVT SENSOR (for Exhaust Side of Bank 2) 11401M (Click here) - -
2 VVT SENSOR (for Intake Side of Bank 2) 11401M (Click here) - -
3 VVT SENSOR (for Exhaust Side of Bank 1) 11401M (Click here) - -
4 VVT SENSOR (for Intake Side of Bank 1) 11401M (Click here) - -
5 INTAKE AIR SURGE TANK 17129 - - -
6 INSPECT FOR ENGINE OIL LEAK - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Engine oil - -

PROCEDURE

Hide 11401M 1.INSTALL VVT SENSOR (for Exhaust Side of Bank 2)

a.
A516022C01
3.031,1.021 2.635,1.021 false 4.688,1.854 4.688,1.635 false 4.698,3.188 4.698,2.969 false 5.792,1.719 5.792,1.5 false 5.802,3.073 5.802,2.854 false 4.729,2.438 4.927,2.135 4.927,2.135 5.094,2.135 true 6.542,2.854 6.292,2.854 false 6.354,1.76 6.167,1.76 6.167,1.76 6.042,1.635 false 6.417,0.781 6.25,0.781 6.25,0.781 6.052,0.906 false 5.5,2.354 5.781,2.354 false 4.698,1.052 4.896,0.75 4.896,0.75 5.063,0.75 true 4.625,1.885 4.938,2.042 0.313,0.156 10 false *1 3.094,0.948 3.427,1.219 0.333,0.271 10 false *b 4.167,0.813 4.479,0.969 0.313,0.156 10 false *c 4.146,2.125 4.458,2.281 0.313,0.156 10 false *d 5.104,0.677 5.417,0.833 0.313,0.156 10 false *a 4.635,3.219 4.979,3.479 0.344,0.26 10 false *1 5.708,1.74 6.021,1.896 0.313,0.156 10 false *1 5.729,3.146 6.042,3.302 0.313,0.156 10 false *1 6.479,0.708 6.792,0.865 0.313,0.156 10 false *a 6.448,1.667 6.76,1.823 0.313,0.156 10 false *a 5.333,2.26 5.646,2.417 0.313,0.156 10 false *a 6.583,2.771 6.896,2.927 0.313,0.156 10 false *a 5.146,2.042 5.458,2.198 0.313,0.156 10 false *a 4.833,1.177 5.052,1.385 0.219,0.208 10 false A 4.854,2.49 5.073,2.698 0.219,0.208 10 false B 4.438,1.177 4.573,1.344 0.135,0.167 10 true A 4.458,2.5 4.594,2.667 0.135,0.167 10 true B 5.833,0.583 6.427,0.875 0.594,0.292 10 false A - A 5.865,2.021 6.458,2.313 0.594,0.292 10 false B - B 0.417,0.115 0.969,0.469 0.552,0.354 18 false i, ii 0.385,2.146 0.938,2.5 0.552,0.354 18 true iii, iv
*1 O-ring - -
*a Seam *b VVT Sensor Tip
*c Correct *d Incorrect


i.

Perform this procedure only when reusing the VVT sensor.

1. Clean the O-ring groove of the VVT sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.


2. Install a new O-ring to the VVT sensor.

NOTICE:

Set the O-ring on the tip of the VVT sensor and roll it into the O-ring groove with bare hands to install it.


3. Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



ii.

Apply a light coat of engine oil to the O-ring of the VVT sensor.


iii.

Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iv.

Connect the VVT sensor connector.



Hide 11401M 2.INSTALL VVT SENSOR (for Intake Side of Bank 2)

a.
A516023C01
2.99,1.021 2.594,1.021 false 4.688,1.854 4.688,1.635 false 4.698,3.188 4.698,2.969 false 5.792,1.719 5.792,1.5 false 5.802,3.073 5.802,2.854 false 4.729,2.438 4.927,2.135 4.927,2.135 5.094,2.135 true 6.542,2.854 6.292,2.854 false 6.354,1.76 6.167,1.76 6.167,1.76 6.042,1.635 false 6.417,0.781 6.25,0.781 6.25,0.781 6.052,0.906 false 5.5,2.354 5.781,2.354 false 4.698,1.052 4.896,0.75 4.896,0.75 5.063,0.75 true 4.625,1.885 4.938,2.042 0.313,0.156 10 false *1 3.021,0.948 3.354,1.219 0.333,0.271 10 false *b 4.167,0.813 4.479,0.969 0.313,0.156 10 false *c 4.146,2.125 4.458,2.281 0.313,0.156 10 false *d 5.104,0.677 5.417,0.833 0.313,0.156 10 false *a 4.635,3.219 4.979,3.479 0.344,0.26 10 false *1 5.708,1.74 6.021,1.896 0.313,0.156 10 false *1 5.729,3.146 6.042,3.302 0.313,0.156 10 false *1 6.479,0.708 6.792,0.865 0.313,0.156 10 false *a 6.448,1.667 6.76,1.823 0.313,0.156 10 false *a 5.333,2.26 5.646,2.417 0.313,0.156 10 false *a 6.583,2.771 6.896,2.927 0.313,0.156 10 false *a 5.146,2.042 5.458,2.198 0.313,0.156 10 false *a 4.833,1.177 5.052,1.385 0.219,0.208 10 false A 4.854,2.49 5.073,2.698 0.219,0.208 10 false B 4.438,1.177 4.573,1.344 0.135,0.167 10 true A 4.458,2.5 4.594,2.667 0.135,0.167 10 true B 5.833,0.583 6.427,0.875 0.594,0.292 10 false A - A 5.865,2.021 6.458,2.313 0.594,0.292 10 false B - B 0.417,0.104 0.969,0.458 0.552,0.354 18 false i, ii 0.448,2 1,2.302 0.552,0.302 18 true iii, iv
*1 O-ring - -
*a Seam *b VVT Sensor Tip
*c Correct *d Incorrect


i.

Perform this procedure only when reusing the VVT sensor.

1. Clean the O-ring groove of the VVT sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.


2. Install a new O-ring to the VVT sensor.

NOTICE:

Set the O-ring on the tip of the VVT sensor and roll it into the O-ring groove with bare hands to install it.


3. Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



ii.

Apply a light coat of engine oil to the O-ring of the VVT sensor.


iii.

Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iv.

Connect the VVT sensor connector.



Hide 11401M 3.INSTALL VVT SENSOR (for Exhaust Side of Bank 1)

a.
A516024C01
2.938,1 2.542,1 false 4.688,1.854 4.688,1.635 false 4.698,3.188 4.698,2.969 false 5.792,1.719 5.792,1.5 false 5.802,3.073 5.802,2.854 false 4.729,2.438 4.927,2.135 4.927,2.135 5.094,2.135 true 6.542,2.854 6.292,2.854 false 6.354,1.76 6.167,1.76 6.167,1.76 6.042,1.635 false 6.417,0.781 6.25,0.781 6.25,0.781 6.052,0.906 false 5.5,2.354 5.781,2.354 false 4.698,1.052 4.896,0.75 4.896,0.75 5.063,0.75 true 4.625,1.885 4.938,2.042 0.313,0.156 10 false *1 2.99,0.885 3.323,1.156 0.333,0.271 10 false *b 4.167,0.813 4.479,0.969 0.313,0.156 10 false *c 4.146,2.125 4.458,2.281 0.313,0.156 10 false *d 5.104,0.677 5.417,0.833 0.313,0.156 10 false *a 4.635,3.219 4.979,3.479 0.344,0.26 10 false *1 5.708,1.74 6.021,1.896 0.313,0.156 10 false *1 5.729,3.146 6.042,3.302 0.313,0.156 10 false *1 6.479,0.708 6.792,0.865 0.313,0.156 10 false *a 6.448,1.667 6.76,1.823 0.313,0.156 10 false *a 5.333,2.26 5.646,2.417 0.313,0.156 10 false *a 6.583,2.771 6.896,2.927 0.313,0.156 10 false *a 5.146,2.042 5.458,2.198 0.313,0.156 10 false *a 4.833,1.177 5.052,1.385 0.219,0.208 10 false A 4.854,2.49 5.073,2.698 0.219,0.208 10 false B 4.438,1.177 4.573,1.344 0.135,0.167 10 true A 4.458,2.5 4.594,2.667 0.135,0.167 10 true B 5.833,0.583 6.427,0.875 0.594,0.292 10 false A - A 5.865,2.021 6.458,2.313 0.594,0.292 10 false B - B 0.417,0.073 0.969,0.427 0.552,0.354 18 false i, ii 0.365,2.135 0.917,2.49 0.552,0.354 18 true iii, iv
*1 O-ring - -
*a Seam *b VVT Sensor Tip
*c Correct *d Incorrect


i.

Perform this procedure only when reusing the VVT sensor.

1. Clean the O-ring groove of the VVT sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.


2. Install a new O-ring to the VVT sensor.

NOTICE:

Set the O-ring on the tip of the VVT sensor and roll it into the O-ring groove with bare hands to install it.


3. Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



ii.

Apply a light coat of engine oil to the O-ring of the VVT sensor.


iii.

Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iv.

Connect the VVT sensor connector.



Hide 11401M 4.INSTALL VVT SENSOR (for Intake Side of Bank 1)

a.
A516025C01
3,0.969 2.604,0.969 false 4.688,1.854 4.688,1.635 false 4.698,3.188 4.698,2.969 false 5.792,1.719 5.792,1.5 false 5.802,3.073 5.802,2.854 false 4.729,2.438 4.927,2.135 4.927,2.135 5.094,2.135 true 6.542,2.854 6.292,2.854 false 6.354,1.76 6.167,1.76 6.167,1.76 6.042,1.635 false 6.417,0.781 6.25,0.781 6.25,0.781 6.052,0.906 false 5.5,2.354 5.781,2.354 false 4.698,1.052 4.896,0.75 4.896,0.75 5.063,0.75 true 4.625,1.885 4.938,2.042 0.313,0.156 10 false *1 3.031,0.885 3.365,1.156 0.333,0.271 10 false *b 4.167,0.813 4.479,0.969 0.313,0.156 10 false *c 4.146,2.125 4.458,2.281 0.313,0.156 10 false *d 5.104,0.677 5.417,0.833 0.313,0.156 10 false *a 4.635,3.219 4.979,3.479 0.344,0.26 10 false *1 5.708,1.74 6.021,1.896 0.313,0.156 10 false *1 5.729,3.146 6.042,3.302 0.313,0.156 10 false *1 6.479,0.708 6.792,0.865 0.313,0.156 10 false *a 6.448,1.667 6.76,1.823 0.313,0.156 10 false *a 5.333,2.26 5.646,2.417 0.313,0.156 10 false *a 6.583,2.771 6.896,2.927 0.313,0.156 10 false *a 5.146,2.042 5.458,2.198 0.313,0.156 10 false *a 4.833,1.177 5.052,1.385 0.219,0.208 10 false A 4.854,2.49 5.073,2.698 0.219,0.208 10 false B 4.438,1.177 4.573,1.344 0.135,0.167 10 true A 4.458,2.5 4.594,2.667 0.135,0.167 10 true B 5.833,0.583 6.427,0.875 0.594,0.292 10 false A - A 5.865,2.021 6.458,2.313 0.594,0.292 10 false B - B 0.417,0.052 0.969,0.406 0.552,0.354 18 false i, ii 0.385,2.052 0.938,2.333 0.552,0.281 18 true iii, iv
*1 O-ring - -
*a Seam *b VVT Sensor Tip
*c Correct *d Incorrect


i.

Perform this procedure only when reusing the VVT sensor.

1. Clean the O-ring groove of the VVT sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.


2. Install a new O-ring to the VVT sensor.

NOTICE:

Set the O-ring on the tip of the VVT sensor and roll it into the O-ring groove with bare hands to install it.


3. Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



ii.

Apply a light coat of engine oil to the O-ring of the VVT sensor.


iii.

Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the VVT sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the VVT sensor.




iv.

Connect the VVT sensor connector.



Hide 6.INSPECT FOR ENGINE OIL LEAK