Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › CRANKSHAFT POSITION SENSOR
RM38G0E _51 Engine / Hybrid System _100527 1GR-FE ENGINE CONTROL _0467385 CRANKSHAFT POSITION SENSOR A

1GR-FE ENGINE CONTROL  CRANKSHAFT POSITION SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

COMPONENTS (INSTALLATION)
A516028N01
4.01,2.938 4.708,3.146 0.698,0.208 6.323,0.198 6.833,0.198 true 2.271,3.042 2.802,3.042 2.802,3.042 2.802,2.729 true 5.698,2.094 6.208,2.094 true 3.76,3.021 4.01,3.021 true 1.875,2.594 2.385,2.594 true 6.281,1.969 6.604,2.313 0.323,0.344 18 false 2 6.177,0.083 6.5,0.427 0.323,0.344 18 false 3 2.063,2.896 2.385,3.24 0.323,0.344 18 false 1 4.094,2.958 4.854,3.177 0.76,0.219 8 false 10 (102, 7) 1.771,2.49 1.927,2.688 0.156,0.198 10 false ●

Procedure Part Name Code
Z101186

Z101188

Z101187

1 CRANKSHAFT POSITION SENSOR 11401G (Click here) - -
2 COMPRESSOR WITH MAGNET CLUTCH - - - -
3 INSPECT FOR ENGINE OIL LEAK - - - (Click here)

V100146

N*m (kgf*cm, ft.*lbf): Specified torque ● Non-reusable part
V100135

Engine oil - -

PROCEDURE

Hide 11401G 1.INSTALL CRANKSHAFT POSITION SENSOR

a.
A516029C01
3.021,0.875 2.75,0.875 false 4.688,1.854 4.688,1.635 false 4.698,3.188 4.698,2.969 false 5.781,1.708 5.781,1.49 false 5.875,3.104 5.875,2.885 false 4.708,2.458 4.906,2.156 4.906,2.156 5.073,2.156 true 6.552,2.854 6.302,2.854 false 6.333,1.76 6.146,1.76 6.146,1.76 6.021,1.635 false 6.406,0.781 6.24,0.781 6.24,0.781 6.042,0.906 false 5.479,2.333 5.76,2.333 false 4.698,1.052 4.896,0.75 4.896,0.75 5.063,0.75 true 4.604,1.865 4.917,2.021 0.313,0.156 10 false *1 3.063,0.792 3.375,0.948 0.313,0.156 10 false *b 4.177,0.823 4.49,0.979 0.313,0.156 10 false *c 4.156,2.24 4.469,2.396 0.313,0.156 10 false *d 5.115,0.635 5.427,0.792 0.313,0.156 10 false *a 4.635,3.229 4.948,3.385 0.313,0.156 10 false *1 5.719,1.76 6.031,1.917 0.313,0.156 10 false *1 5.781,3.135 6.094,3.292 0.313,0.156 10 false *1 6.427,0.667 6.74,0.823 0.313,0.156 10 false *a 6.406,1.677 6.719,1.833 0.313,0.156 10 false *a 5.323,2.25 5.635,2.406 0.313,0.156 10 false *a 6.604,2.75 6.917,2.906 0.313,0.156 10 false *a 5.135,2.094 5.448,2.25 0.313,0.156 10 false *a 4.833,1.177 5.052,1.385 0.219,0.208 10 false A 4.854,2.51 5.073,2.719 0.219,0.208 10 false B 4.427,1.188 4.563,1.354 0.135,0.167 10 true A 4.448,2.51 4.583,2.677 0.135,0.167 10 true B 5.833,0.594 6.427,0.885 0.594,0.292 10 false A - A 5.865,1.99 6.458,2.281 0.594,0.292 10 false B - B 0.385,0.063 0.938,0.417 0.552,0.354 18 false i, ii 0.396,2.115 0.948,2.469 0.552,0.354 18 true iii, iv
*1 O-ring - -
*a Seam *b Crankshaft Position Sensor Tip
*c Correct *d Incorrect


i.

Perform this procedure only when reusing the crankshaft position sensor.

1. Clean the O-ring groove of the crankshaft position sensor.

NOTICE:

Make sure the O-ring groove is free of foreign matter.


2. Install a new O-ring to the crankshaft position sensor.

NOTICE:

Set the O-ring on the tip of the crankshaft position sensor and roll it into the O-ring groove with bare hands to install it.


3. Check if the O-ring is twisted.

HINT:

Check the entire circumference of the seam of the O-ring for twisting.



ii.

Apply a light coat of engine oil to the O-ring of the crankshaft position sensor.


iii.

Install the crankshaft position sensor to the cylinder block sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

If the crankshaft position sensor has been struck or dropped, replace it.

·

Make sure that the O-ring is not cracked or moved out of place when installing the crankshaft position sensor.




iv.

Connect the crankshaft position sensor connector.



Hide 3.INSPECT FOR ENGINE OIL LEAK