Home › Drivetrain › JF2BM (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM38G0E _52 Drivetrain _100437 JF2BM TRANSFER / 4WD / AWD _0467431 TRANSFER SYSTEM C

JF2BM TRANSFER / 4WD / AWD  TRANSFER SYSTEM  P17C213  4WD/AWD Rear Differential Unit Actuator "A" Control Circuit Circuit Open  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
P17C213 4WD/AWD Rear Differential Unit Actuator "A" Control Circuit Circuit Open
Diagnosis Condition:
·

Ignition switch ON

·

Rear differential lock solenoid is not powered on or is operating


Malfunction Status:
·

Open circuit in solenoid drive circuit


Malfunction Time:
·

Not powered on: 1 second or more

·

Operating: 5 seconds or more


Number of Trips:
·

1 trip


·

Wire harness and connector

·

Rear differential lock solenoid (electronic differential lock case sub-assembly)

·

4 wheel drive control ECU


Four Wheel Drive

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Ignition switch ON ○ ○
Rear differential lock solenoid is not powered on ○ -
Rear differential lock solenoid is operating - ○
Malfunction Status Open circuit in the front differential lock solenoid drive circuit ○ ○
Detection Time 1 second or more 5 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - REAR DIFFERENTIAL LOCK SOLENOID (ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY))
a.

Disconnect the B11 4 wheel drive control ECU connector.


b.

Disconnect the V11 rear differential lock solenoid (electronic differential lock case sub-assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B11,V11)Location & Routing

Click Connector(B11)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

Click Connector(V11)Body>Differential Wire / Frame Wire>Differential Lock Solenoid (Rear Differential Assembly)

B11-10 (SL+) - V11-2 (M1) Always Below 1 Ω
B11-9 (SL-) - V11-1 (M2) Always Below 1 Ω
B11-10 (SL+) or V11-2 (M1) - Body ground Always 10 kΩ or higher
B11-9 (SL-) or V11-1 (M2) - Body ground Always 10 kΩ or higher



d.

Connect the B11 4 wheel drive control ECU connector.


e.

Connect the V11 rear differential lock solenoid (electronic differential lock case sub-assembly) connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT REAR DIFFERENTIAL LOCK SOLENOID (ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT REAR DIFFERENTIAL LOCK SOLENOID (ELECTRONIC DIFFERENTIAL LOCK CASE SUB-ASSEMBLY)
a.

Disconnect the B11 4 wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(B11)Location & Routing

Click Connector(B11)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>4 Wheel Drive Control ECU

B11-10 (SL+) - B11-9 (SL-) 20°C (68°F) 2.64 to 2.94 Ω



c.

Connect the B11 4 wheel drive control ECU connector.


Result:
Proceed to
OK
NG



OK

NG