The combination meter assembly and radio and display receiver assembly*1 or radio receiver assembly*2 communicate via local bus communication. This allows audio and visual system information to be displayed on the multi-information display. This DTC is stored when a communication error occurs between the radio and display receiver assembly*1 or radio receiver assembly*2 and combination meter assembly.
*1: for Radio and Display Type
*2: for Radio Receiver Type, with Multi-display
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B132187 | Lost Communication with EMV Missing Message | Diagnosis Condition:
·
Ignition switch ON
·
IG power source voltage is 9.5 V or more Malfunction Status: No communication with Radio and Display Receiver Assembly*1 or Radio Receiver Assembly*2 Malfunction Time: 3.0 seconds or more |
·
Harness or connector
·
Radio and Display Receiver Assembly (for Radio and Display Type)
·
Radio Receiver Assembly (for Radio Receiver Type, with Multi-display)
·
Combination meter assembly
·
Meter mirror sub-assembly (w/ Headup Display System) |
| Pattern | DTC Output Part Name (Display on GTS) |
Suspected Area (Malfunction Status) | |||
|---|---|---|---|---|---|
| Combination Meter | Navigation System | Head up Display | |||
| B132187 | B1324 | B1325 | B132187 | ||
|
○: DTC is output. -: DTC is not output |
|||||
| Pattern 1 | ○ | ○ | ○ | ○ | Local bus (Open or short) |
| Meter mirror sub-assembly (Internal malfunction) | |||||
| Combination meter assembly (Internal malfunction) | |||||
| Radio and Display Receiver Assembly (for Radio and Display Type) | |||||
| Radio Receiver Assembly (for Radio Receiver Type, with Multi-display) | |||||
| Pattern 2 | ○ | ○ | - | - | Local bus branch line (Open) |
| Combination meter assembly (Internal malfunction) | |||||
| Pattern 3 | ○ | - | - | - | Combination meter assembly (Internal malfunction) |
| Pattern 4 | ○ | - | - | ○ | Radio and Display Receiver Assembly (for Radio and Display Type) |
| Radio Receiver Assembly (for Radio Receiver Type, with Multi-display) | |||||
| Pattern | DTC Output Part Name (Display on GTS) |
Suspected Area (Malfunction Status) | |
|---|---|---|---|
| Combination Meter | Navigation System | ||
| B132187 | B1324 | ||
|
○: DTC is output. -: DTC is not output |
|||
| Pattern 1 | ○ | ○ | Local bus (Open or short) |
| Combination meter assembly (Internal malfunction) | |||
| Radio and Display Receiver Assembly (for Radio and Display Type) | |||
| Radio Receiver Assembly (for Radio Receiver Type, with Multi-display) | |||
| Pattern 2 | ○ | - | Radio and Display Receiver Assembly (for Radio and Display Type) |
| Radio Receiver Assembly (for Radio Receiver Type, with Multi-display) | |||
| Combination meter assembly (Internal malfunction) | |||
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
When the combination meter assembly is replaced, update the ECU security key.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY
After the ignition is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Check vehicle condition.
| Result | Proceed to |
|---|---|
| w/ Headup Display System | A |
| w/o Headup Display System | B |
A
B
Check if meter/gauge system DTCs are output.
Check if audio and visual system*1 or navigation system*2 DTCs are output.
*1: w/ Audio and Visual System
*2: w/ Navigation System
Check if headup display system DTCs are output.
Check for the DTCs and output pattern according to the following table.
| Pattern | DTC Output GTS Display Name | |||
|---|---|---|---|---|
| Combination Meter | Navigation System | Head up Display | ||
| B132187 | B1324 | B1325 | B132187 | |
|
○: DTC is output. -: DTC is not output |
||||
| Pattern 1 | ○ | ○ | ○ | ○ |
| Pattern 2 | ○ | ○ | - | - |
| Pattern 3 | ○ | - | - | - |
| Pattern 4 | ○ | - | - | ○ |
| Result | Proceed to |
|---|---|
| Pattern 1 | A |
| Pattern 2 | B |
| Pattern 3 | C |
| Pattern 4 (for Radio and Display Type) | D |
| Pattern 4 (for Radio Receiver Type, with Multi-display) | E |
A
B
C
D
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
E
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL
Disconnect the I17 meter mirror sub-assembly connector.
Clear the DTCs.
Check for DTCs.
If DTC B132187 is output from the meter / gauge system and is not output from the navigation system and audio and visual system or headup display system, it can be suspected that the combination meter assembly has an internal malfunction.
If DTC B132187 is output from the headup display system or meter / gauge system and is not output from the navigation system and audio and visual system, it can be suspected that the radio and display receiver assembly has an internal malfunction.
| Result | Proceed to |
|---|---|
| DTC B132187 is output. | A |
| DTC B132187 is not output. | B |
A
B
Disconnect the cable from the negative (-) battery terminal.
Disconnect the I5 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I5,I76)Location & Routingewd_type=routing;type=c,c;code=I5,I76 |
||
| I5-14 (MSCH) - I5-30 (MSCL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I5-14 (MSCH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I5-30 (MSCL) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I5-14 (MSCH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I5-30 (MSCL) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio and Display Type
*2: for Radio Receiver Type, with Multi-display
Disconnect the cable from the negative (-) battery terminal.
Disconnect the I12 radio and display receiver assembly connector.*1
Disconnect the I13 radio receiver assembly connector.*2
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I12,I76)Location & Routingewd_type=routing;type=c,c;code=I12,I76 |
||
| I12-5 (CNH1) - I12-6 (CNL1) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I12-5 (CNH1) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I12-6 (CNL1) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I12-5 (CNH1) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I12-6 (CNL1) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I13,I76)Location & Routingewd_type=routing;type=c,c;code=I13,I76 |
||
| I13-5 (CNH1) - I13-6 (CNL1) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I13-5 (CNH1) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I13-6 (CNL1) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I13-5 (CNH1) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I13-6 (CNL1) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK (for Radio and Display Type) |
| OK (for Radio Receiver Type, with Multi-display) |
| NG |
OK (for Radio and Display Type)
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
OK (for Radio Receiver Type, with Multi-display)
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the I5 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I5)Location & Routingewd_type=routing;type=c;code=I5 |
||
| I5-14 (MSCH) - I5-30 (MSCL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if meter/gauge system DTCs are output.
Check if audio and visual system*1 or navigation system*2 DTCs are output.
*1: w/ Audio and Visual System
*2: w/ Navigation System
Check for the DTCs and output pattern according to the following table.
| Pattern | DTC Output GTS Display Name | |
|---|---|---|
| Combination Meter | Navigation System | |
| B132187 | B1324 | |
|
○: DTC is output. -: DTC is not output |
||
| Pattern 1 | ○ | ○ |
| Pattern 2 | ○ | - |
| Result | Proceed to |
|---|---|
| Pattern 1 | A |
| Pattern 2 (for Radio and Display Type) | B |
| Pattern 2 (for Radio Receiver Type, with Multi-display) | C |
A
B
C
Disconnect the cable from the negative (-) battery terminal.
Disconnect the I5 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I5,I76)Location & Routingewd_type=routing;type=c,c;code=I5,I76 |
||
| I5-14 (MSCH) - I5-30 (MSCL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I5-14 (MSCH) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I5-30 (MSCL) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I5-14 (MSCH) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I5-30 (MSCL) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for Radio and Display Type
*2: for Radio Receiver Type, with Multi-display
Disconnect the cable from the negative (-) battery terminal.
Disconnect the I12 radio and display receiver assembly connector.*1
Disconnect the I13 radio receiver assembly connector.*2
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I12,I76)Location & Routingewd_type=routing;type=c,c;code=I12,I76 |
||
| I12-5 (CNH1) - I12-6 (CNL1) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I12-5 (CNH1) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I12-6 (CNL1) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I12-5 (CNH1) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I12-6 (CNL1) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
Click Location & Routing(I13,I76)Location & Routingewd_type=routing;type=c,c;code=I13,I76 |
||
| I13-5 (CNH1) - I13-6 (CNL1) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| I13-5 (CNH1) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I13-6 (CNL1) - I76-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| I13-5 (CNH1) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| I13-6 (CNL1) - I76-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK (for Radio and Display Type) |
| OK (for Radio Receiver Type, with Multi-display) |
| NG |
OK (for Radio and Display Type)
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
OK (for Radio Receiver Type, with Multi-display)
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL
NG
Disconnect the I5 combination meter assembly connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
Click Location & Routing(I5)Location & Routingewd_type=routing;type=c;code=I5 |
|||
| I5-14 (MSCH) - I5-30 (MSCL) | Ignition switch ON | 1 V/DIV., 100 μs./DIV. | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Disconnect the I5 combination meter assembly connector.
Using an oscilloscope, check the waveform.
| Tester Connection | Switch Condition | Tool Setting | Specified Condition |
|---|---|---|---|
Click Location & Routing(I5)Location & Routingewd_type=routing;type=c;code=I5 |
|||
| I5-14 (MSCH) - I5-30 (MSCL) | Ignition switch ON | 1 V/DIV., 100 μs./DIV. | Pulse generation |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio Receiver Type)>REMOVAL