Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The combination meter assembly receives vehicle speed signals from the brake actuator assembly (No. 2 skid control ECU) via CAN communication. The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly (No. 2 skid control ECU). The brake actuator assembly (No. 2 skid control ECU) supplies power to the vehicle speed sensor. The brake actuator assembly (No. 2 skid control ECU) detects vehicle speed signals based on pulses of the voltage.

HINT:
·

Factors that affect the indicated vehicle speed include the tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using the GTS. For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK

·

If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly (No. 2 skid control ECU) stores DTCs. Troubleshoot the electronically controlled brake system.



WIRING DIAGRAM

E407708E17
4.667,1.583 6.542,1.917 1.875,0.333 10 false Combination Meter Assembly 0.698,2.26 2.781,2.563 2.083,0.302 10 false : CAN Communication Line 1.052,1.594 2.698,2.031 1.646,0.438 10 false Brake Actuator Assembly (No. 2 Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

If the vehicle speed is outside the allowable range when tested, perform the operation check inspection.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

When the combination meter assembly is replaced, update the ECU security key.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>UPDATE ECU SECURITY KEY



HINT:

Before starting the following inspection, check tire size and tire air pressure.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.CHECK FOR DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)

B

2.CHECK FOR DTC (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Check for DTCs.

Chassis > Brake/EPB > Trouble Codes
50001 435

Result:
Result Proceed to
Electronically controlled brake system DTCs are not output. A
Electronically controlled brake system DTC is output. B



A

3.PERFORM ACTIVE TEST USING GTS

B

3.PERFORM ACTIVE TEST USING GTS
a.

Using the GTS, read the Data List.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST

Body Electrical > Combination Meter > Active Test
Tester Display Control Range Diagnostic Note
Speedometer Operation (0km/h,0MPH) Speedometer 0 km/h (0 mph) -
Speedometer Operation (40km/h,40MPH) Speedometer 40 km/h (40 mph) The value displayed on the speedometer may deviate.
Reference km/h:
40 → 42.0 to 46.0
Speedometer Operation (80km/h,80MPH) Speedometer 80 km/h (80 mph) The value displayed on the speedometer may deviate.
Reference km/h:
80 → 84.0 to 88.0
Speedometer Operation (120km/h,120MPH) Speedometer 120 km/h (120 mph) The value displayed on the speedometer may deviate.
Reference km/h:
120 → 125.0 to 130.0
Speedometer Operation (160km/h,160MPH) Speedometer 160 km/h (160 mph) The value displayed on the speedometer may deviate.
Reference km/h:
160 → 167.0 to 173.0
Speedometer Operation (200km/h,200MPH) Speedometer 200 km/h (200 mph) The value displayed on the speedometer may deviate.
Reference km/h:
200 → 208.0 to 215.0
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (0km/h,0MPH)
50004 409 199
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (40km/h,40MPH)
50004 409 200
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (80km/h,80MPH)
50004 409 201
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (120km/h,120MPH)
50004 409 202
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (160km/h,160MPH)
50004 409 203
Body Electrical > Combination Meter > Active Test
Tester Display
Speedometer Operation (200km/h,200MPH)
50004 409 204
OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY