Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100611 METER / GAUGE / DISPLAY _0467504 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B150113  Sub Fuel Sender Circuit Open  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a No. 2 fuel sender gauge assembly malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B150113 Sub Fuel Sender Circuit Open When IG voltage is 9.5 V or more and the following condition is detected:
·

Average input signal of fuel sender gauge assembly is 630 Ω or more 3 times consecutively


·

Harness or connector

·

No. 2 fuel sender gauge assembly

·

Fuel tank vent tube assembly

·

Combination meter assembly


-

WIRING DIAGRAM

E466216E02
0.458,3.396 0.729,3.604 0.271,0.208 10 false V10 0.469,3.573 2.438,3.781 1.969,0.208 10 false Fuel Tank Vent Tube Assembly 5.417,1.969 6.313,2.302 0.896,0.333 10 false FR 2.75,1.938 3.458,2.281 0.708,0.344 10 false FR2 3.156,1.927 3.323,2.125 0.167,0.198 10 false 3 5.094,2.49 5.99,2.823 0.896,0.333 10 false 34 5.115,1.438 6.01,1.771 0.896,0.333 10 false 24 5.406,2.469 5.833,2.667 0.427,0.198 10 false FE 5.417,1.417 6.313,1.75 0.896,0.333 10 false FV 6.344,1.146 6.531,1.365 0.188,0.219 10 false IG 3.167,2.448 3.323,2.656 0.156,0.208 10 false 2 3.125,1.375 3.26,1.542 0.135,0.167 10 false 1 1.396,1.396 2,1.698 0.604,0.302 10 false 1 1.365,2.469 1.969,2.771 0.604,0.302 10 false 2 1.365,1.938 2.26,2.271 0.896,0.333 10 false 3 2.74,1.396 3.167,1.615 0.427,0.219 10 false FV2 2.75,2.49 3.281,2.76 0.531,0.271 10 false FE2 0.604,2.917 2.854,3.146 2.25,0.229 10 false No. 2 Fuel Sender Gauge Assembly 5.26,3.406 6.927,3.688 1.667,0.281 10 false I5 5.26,3.552 7.125,4.229 1.865,0.677 10 false Combination Meter Assembly 6.333,2.021 6.646,2.188 0.313,0.167 10 false CPU 5.917,2.042 6.115,2.25 0.198,0.208 10 false I/F 5.135,1.958 5.323,2.188 0.188,0.229 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY

OK

2.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

2.INSPECT FUEL TANK VENT TUBE ASSEMBLY
E442852E04
0.385,1.292 0.719,1.521 0.333,0.229 0.375,3.719 0.708,3.948 0.333,0.229 1.344,1.229 0.906,0.708 true 2.083,1.219 2.458,0.615 true 1.729,1.198 1.729,0.469 true 0.521,1.333 0.74,1.531 0.219,0.198 10 false A 0.51,3.76 0.729,3.958 0.219,0.198 10 false B 0.76,0.542 1.167,0.781 0.406,0.24 10 false FV2 1.625,0.281 2.135,0.615 0.51,0.333 10 false FE2 2.365,0.448 2.76,0.719 0.396,0.271 10 false FR2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (FV2) - B-1 Always Below 1 Ω
A-2 (FE2) - B-2 Always Below 1 Ω
A-3 (FR2) - B-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (FUEL TANK VENT TUBE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the V10 No. 2 fuel tank vent tube assembly connector.


b.

Disconnect the I5 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(V10,I5)Location & Routing

Click Connector(V10)Body>Differential Wire / Frame Wire>Fuel Pump (Fuel Tank Sub-Assembly)

Click Connector(I5)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Combination Meter Assembly

V10-3 (FR2) - I5-8 (FR) Always Below 1 Ω
V10-2 (FE2) - I5-34 (FE) Always Below 1 Ω
V10-1 (FV2) - I5-24 (FV) Always Below 1 Ω
I5-8 (FR) - Body ground Always 10 kΩ or higher
I5-34 (FE) - Body ground Always 10 kΩ or higher
I5-24 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR