Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  P057162  Brake Switch "A" Signal Compare Failure  


DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority Note
P057162 Brake Switch "A" Signal Compare Failure The brake signal sent via direct line and the brake signal sent via CAN communication do not match. (1-trip detection logic*)
·

Electronically controlled brake system

·

Stop light switch assembly

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Power Source Control A
DTC Output Confirmation Operation:

Connect the cable to the negative (-) battery terminal, release the brake pedal and wait at least 20 seconds. Then depress the brake pedal for 20 seconds or more.



*: Only detected while a malfunction is present and the ignition switch is ON.


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
·

If there is a malfunction when the brake signal sent via direct line is on, the engine can be started by pressing the engine switch with the brake pedal released.

·

If there is a malfunction when the brake signal sent via direct line is off, the engine cannot be started by pressing the engine switch with the brake pedal depressed.

-

With the electrical key transmitter sub-assembly in the cabin, even if an engine start operation is performed, the engine does not start (the key indicator display is not displayed on the multi-information display). However, the engine can be started by turning the ignition switch to ACC and then pressing and holding it.



-

Related Data List and Active Test Items
DTC No. Data List and Active Test
P057162
Power Source Control
·

Stop Light Switch



WIRING DIAGRAM

B616492E01
5.333,2.583 5.792,2.781 0.458,0.198 10 false L 5.719,2.698 6.177,2.896 0.458,0.198 10 false IC 5.958,0.896 6.417,1.094 0.458,0.198 10 false IC 5.313,0.719 5.771,0.917 0.458,0.198 10 false STP1 1.594,0.823 2.125,1.052 0.531,0.229 10 false STP2 1.656,2.708 2.115,2.906 0.458,0.198 10 false STP 1.667,4.323 2.125,4.521 0.458,0.198 10 false STP 5.063,0.708 5.521,0.906 0.458,0.198 10 false 21 5.125,2.583 5.583,2.781 0.458,0.198 10 false 3 2.052,0.74 2.51,0.938 0.458,0.198 10 false 37 2.063,2.583 3.208,2.813 1.146,0.229 10 false 7*1, 22*2 2.063,4.208 2.521,4.406 0.458,0.198 10 false 36 4.24,1.385 4.698,1.583 0.458,0.198 10 false I40 4.938,3.01 5.396,3.208 0.458,0.198 10 false B43 0.25,1.375 0.844,1.646 0.594,0.271 10 false B20 1.031,3.135 2.104,3.365 1.073,0.229 10 false B2*1, B1*2 0.521,4.615 0.979,4.813 0.458,0.198 10 false C36 0.583,5.427 2.698,5.646 2.115,0.219 10 false : CAN Communication Line 0.521,4.781 2.865,5.073 2.344,0.292 10 false Transmission Control ECU 1.229,3.323 1.625,3.719 0.396,0.396 10 false ECM 0.24,1.542 3.521,2.01 3.281,0.469 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 4.219,1.542 7.094,1.885 2.875,0.344 10 false Certification ECU (Smart Key ECU Assembly) 4.927,3.167 6.875,3.583 1.948,0.417 10 false Stop Light Switch Assembly 3.01,5.01 5.156,5.208 2.146,0.198 10 false *1: for 1GR-FE 3.01,5.375 5.156,5.573 2.146,0.198 10 false *2: for V35A-FTS

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

After the ignition is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch State of brake pedal OFF or ON OFF: Brake pedal released
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch
50003 454 206
OK:

The GTS display changes correctly in response to the brake pedal operation.


Result:
Result Proceed to
The value of Stop Light Switch is OFF A
The value of Stop Light Switch is not OFF B




A

2.READ VALUE USING GTS (STOP LIGHT SWITCH)

B

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
2.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch State of brake pedal OFF or ON ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch
50003 454 206
OK:

The GTS display changes correctly in response to the brake pedal operation.


Result:
Result Proceed to
The value of Stop Light Switch is ON A
The value of Stop Light Switch is not ON B




A

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

Pre-procedure1

a.

Disconnect the I40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the B43 stop light switch assembly connector.


c.

Disconnect the B20 No. 2 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the B2*1, B1*2 ECM connector.

*1: for 1GR-FE

*2: for V35A-FTS


e.

Disconnect the C36 transmission control ECU connector.


Procedure1

f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I40,B43)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

Click Connector(B43)Instrument Panel>Engine Room Main Wire / Heater Blower Wire>Stop Light Switch Assembly

I40-21 (STP1) - B43-3 (L) Always Below 1 Ω


Result:
Proceed to
OK
NG



Post-procedure1

g.

None



OK

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

Pre-procedure1

a.

Connect the I40 certification ECU (smart key ECU assembly) connector.


b.

Connect the B43 stop light switch assembly connector.


Procedure1

c.
B574625C52
1.354,0.052 1.719,0.24 0.365,0.188 0.917,2 1.333,2 1.333,2 2.146,0.938 true 0.156,0.073 0.469,0.229 0.313,0.156 10 false *a 1.417,0.063 1.729,0.219 0.313,0.156 10 false I40 0.531,1.917 0.969,2.104 0.438,0.188 10 false STP1
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I40)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I40-21 (STP1) - Body ground Brake pedal released 1 V or less
I40-21 (STP1) - Body ground Brake pedal depressed 9 V or higher


Result:
Proceed to
OK
NG



Post-procedure1

d.

None



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY