Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG)  


DESCRIPTION

If the engine switch is pressed with the electrical key transmitter sub-assembly in the cabin, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to on (IG) but does change to on (ACC)
Power Source Control
·

Power Supply Condition

·

IGP Relay Circuit (Outside) Monitor

·

IGP Relay Circuit (Inside) Monitor

·

IGR Relay Circuit (Outside) Monitor

·

IGR Relay Circuit (Inside) Monitor



WIRING DIAGRAM

B612745E02
4.563,0.146 6.188,0.344 1.625,0.198 10 false from Battery 5.188,0.958 6.26,1.167 1.073,0.208 10 false ECU-IGR NO.1 5.146,2.063 6.24,2.25 1.094,0.188 10 false ECU-IGR NO.2 4.542,1.531 5.458,1.729 0.917,0.198 10 false IGR NO.1 4.542,2.625 5.458,2.823 0.917,0.198 10 false IGR NO.2 6.292,0.635 6.604,0.833 0.313,0.198 10 false 34 6.302,2.167 6.615,2.365 0.313,0.198 10 false 36 6.292,1.74 6.604,1.938 0.313,0.198 10 false 38 3.74,0.615 4.052,0.813 0.313,0.198 10 false 1 3.708,1.063 4.021,1.26 0.313,0.198 10 false 11 3.698,2.177 4.01,2.375 0.313,0.198 10 false 17 6.292,0.823 6.604,1.021 0.313,0.198 10 false 5C 6.292,1.917 6.604,2.115 0.313,0.198 10 false 5B 6.302,2.365 6.615,2.563 0.313,0.198 10 false 5B 3.688,0.823 4,1.021 0.313,0.198 10 false 5K 3.688,1.26 4,1.458 0.313,0.198 10 false 5B 3.698,2.385 4.01,2.583 0.313,0.198 10 false 5C 1.708,1.146 2.021,1.344 0.313,0.198 10 false 11 1.688,2.281 2,2.479 0.313,0.198 10 false 24 1.302,1.156 1.781,1.365 0.479,0.208 10 false IGRD 1.313,2.281 1.792,2.49 0.479,0.208 10 false IGPD 1.073,0.771 1.385,0.969 0.313,0.198 10 false +B 1.073,1.896 1.385,2.094 0.313,0.198 10 false +B 0.708,1.125 1.021,1.323 0.313,0.198 10 false IC 0.708,2.25 1.021,2.448 0.313,0.198 10 false IC 0.24,3.146 0.552,3.344 0.313,0.198 10 false I40 0.229,3.292 1.76,3.771 1.531,0.479 10 false Certification ECU (Smart Key ECU Assembly) 4.073,3.146 6.521,3.802 2.448,0.656 10 false Power Distribution Box Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.

·

If the entry and start system (for Start Function) has been disabled, enable the system before performing troubleshooting.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After performing repairs, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."



HINT:
·

If interior verification is unsuccessful, Vehicle Control History may be stored.

·

If Vehicle Control History has been stored, refer to the Vehicle Control History List to determine the detection conditions and narrow down trouble areas.



Body Electrical > Entry&Start > Utility
Tester Display
Vehicle Control History (RoB)
50005 440 62

PROCEDURE

1.CHECK FOR DTC
a.

Using the GTS, check for certification ECU (smart key ECU assembly) DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 454
Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTCs are not output A
Entry and start system (for Start Function) DTCs are output B



A

2.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) AND BODY GROUND)
a.

Disconnect the I40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 5B and 5C power distribution box assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I40)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I40-24 (IGPD) - 5C-17 Always Below 1 Ω
I40-11 (IGRD) - 5B-11 Always Below 1 Ω
5B-36 - Body ground Always Below 1 Ω
I40-24 (IGPD) or 5C-17 - Other terminals and body ground Always 10 kΩ or higher
I40-11 (IGRD) or 5B-11 - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.
B574625C53
1.354,0.031 1.74,0.25 0.385,0.219 2.094,2.01 1.979,2.01 1.979,2.01 1.688,0.917 false 2.281,1.854 2.167,1.854 2.167,1.854 1.76,0.802 false 1.448,0.073 1.906,0.271 0.458,0.198 10 false I40 2.333,1.771 2.948,1.969 0.615,0.198 10 false IGRD 2.156,1.948 2.771,2.146 0.615,0.198 10 false IGPD 0.188,0.052 0.802,0.25 0.615,0.198 10 false *a
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Connect the I40 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition

Click Location & Routing(I40)Location & Routing

Click Connector(I40)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Certification ECU

I40-11 (IGRD) - Body ground Ignition switch ACC → Ignition switch ON 1 V or less → 9 V or higher
I40-24 (IGPD) - Body ground Ignition switch ACC → Ignition switch ON 1 V or less → 9 V or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER SOURCE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - POWER SOURCE)
a.

Disconnect the I40 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the 5B, 5C and 5K power distribution box assembly connectors.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5K-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR