Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100610 THEFT DETERRENT / KEYLESS ENTRY _0467507 ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  System Malfunction Message is Displayed on the Multi-information Display  


SYSTEM DESCRIPTION

If an abnormal operation that may lead to a malfunction of the steering lock ECU (steering lock actuator with ECU assembly), or abnormal vehicle speed information is detected by the certification ECU (smart key ECU assembly), a system malfunction message is displayed on the multi-information display.

WIRING DIAGRAM

B612581E03
5.927,0.865 6.542,1.063 0.615,0.198 10 false SLR+ 5.938,1.385 6.552,1.583 0.615,0.198 10 false E 6.271,2.844 6.885,3.042 0.615,0.198 10 false +B 6.583,3.49 6.917,3.729 0.333,0.24 10 false IC 5.917,3.229 6.531,3.427 0.615,0.198 10 false STAR 5.927,4.333 6.542,4.531 0.615,0.198 10 false STA 5.594,0.688 6.208,0.885 0.615,0.198 10 false 24 5.604,1.177 6.219,1.375 0.615,0.198 10 false 29 5.604,3.135 6.219,3.333 0.615,0.198 10 false 10 5.646,4.125 6.26,4.323 0.615,0.198 10 false 3 5.573,0.885 6.188,1.083 0.615,0.198 10 false I39 5.573,1.385 6.188,1.583 0.615,0.198 10 false I39 5.594,3.333 6.208,3.531 0.615,0.198 10 false I40 5.594,4.333 6.208,4.531 0.615,0.198 10 false I40 5.615,4.802 7.146,5.354 1.531,0.552 10 false Certification ECU (Smart Key ECU Assembly) 2,0.24 2.615,0.438 0.615,0.198 10 false 7 2,0.781 2.615,0.979 0.615,0.198 10 false 3 2,1.271 2.615,1.469 0.615,0.198 10 false 1 1.813,0.333 2.438,0.531 0.625,0.198 10 false B 1.688,0.875 2.313,1.073 0.625,0.198 10 false IGE 1.635,1.375 2.26,1.573 0.625,0.198 10 false GND 0.125,1.833 0.74,2.031 0.615,0.198 10 false I49 0.115,2 2.792,2.521 2.677,0.521 10 false Steering Lock ECU (Steering Lock Actuator with ECU Assembly) 1.396,3.333 2.344,3.531 0.948,0.198 10 false C92 1.417,4.125 2.479,4.354 1.063,0.229 10 false 16 0.948,3.333 1.573,3.531 0.625,0.198 10 false NSW 0.99,4.313 1.604,4.51 0.615,0.198 10 false STA 0.677,4.802 1.896,5.365 1.219,0.563 10 false ECM 2.208,0.49 3.083,0.719 0.875,0.229 10 false STRG LOCK 3.396,0.354 5.094,0.656 1.698,0.302 10 false from Battery 0.417,5.344 2.104,5.583 1.688,0.24 10 false *1: for 1GR-FE 2.021,5.344 3.708,5.583 1.688,0.24 10 false *2: for V35A-FTS 1.833,4.125 2.896,4.354 1.063,0.229 10 false 34 1.427,4.333 2.49,4.563 1.063,0.229 10 false B2 1.448,4.573 2.51,4.802 1.063,0.229 10 false *1 1.844,4.563 2.906,4.792 1.063,0.229 10 false *2 1.833,4.333 2.896,4.563 1.063,0.229 10 false B1 1.427,3.146 2.375,3.344 0.948,0.198 10 false 48 1.438,3.542 2.385,3.74 0.948,0.198 10 false *1 1.802,3.323 2.75,3.521 0.948,0.198 10 false C37 1.844,3.531 2.792,3.729 0.948,0.198 10 false *2 1.906,3.146 2.854,3.344 0.948,0.198 10 false 7

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator with ECU assembly), refer to Service Bulletin.



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440
Body Electrical > Power Source Control > Trouble Codes
50001 454

Result:
Result Proceed to
DTCs are not output A
DTC is output. B



A

2.READ VALUE USING GTS (SENSOR MALFUNCTION HISTORY)

B

GO TO ENTRY AND START SYSTEM (for Entry Function) (DIAGNOSTIC TROUBLE CODE CHART)

2.READ VALUE USING GTS (SENSOR MALFUNCTION HISTORY)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sensor Malfunction History History of malfunction of position sensor in steering lock ECU (steering lock actuator with ECU assembly) (DTC B278196 is stored) OK or NG OK: History of malfunction for the lock or unlock sensor in the steering lock ECU (steering lock actuator with ECU assembly) does not exist.
NG: History of both the lock and unlock sensors in the steering lock ECU (steering lock actuator with ECU assembly) being on exists. (Under normal operation, neither sensor is on.)
When NG is displayed, either the position sensor in the steering lock ECU (steering lock actuator with ECU assembly) or the assembly itself may be malfunctioning.
Body Electrical > Entry&Start > Data List
Tester Display
Sensor Malfunction History
50003 440 48
OK:

OK is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (VEHICLE RUNNING CONDITION (LINE))

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

3.READ VALUE USING GTS (VEHICLE RUNNING CONDITION (LINE))
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Running Condition (Line) Vehicle being driven or stopped Stop or Driving Stop: Vehicle stopped
Driving: Vehicle being driven at 5 km/h (3 mph) or more
-
Body Electrical > Power Source Control > Data List
Tester Display
Vehicle Running Condition (Line)
50003 454 402
OK:

The GTS display changes correctly in response to the vehicle condition.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND BODY GROUND)

NG

GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE AND BODY GROUND)
a.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-1 (GND) - Body ground Always Below 1 Ω


NOTICE:

If the result is not as specified, check for looseness in the ground cable connection.



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.

Connect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.
B518305C32
1.49,0.99 1.896,1.25 0.406,0.26 2.354,2.885 1.885,2.885 1.885,2.885 1.885,1.979 true 2.719,2.677 2.25,2.677 2.25,2.677 2.25,1.99 true 0.188,0.281 0.5,0.438 0.313,0.156 10 false *a 1.573,1.031 2.073,1.302 0.5,0.271 10 false I49 2.448,2.802 2.948,3.073 0.5,0.271 10 false IGE 2.781,2.604 3.281,2.875 0.5,0.271 10 false GND
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator with ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-3 (IGE) - I49-1 (GND)

Steering lock motor operating when all conditions met, and then door opened:

-

The steering is unlocked.

-

The ignition switch is off.

-

The shift lever is in P.



11 to 14 V → Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
6.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY) - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.



Result:
Proceed to
OK
NG



OK

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.

Connect the I49 steering lock ECU (steering lock actuator with ECU assembly) connector.


b.
C435466C05
1.49,0.938 1.906,1.198 0.417,0.26 2.344,2.948 1.896,2.948 1.896,2.948 1.896,1.969 true 0.177,0.208 0.49,0.365 0.313,0.156 10 false *a 2.385,2.844 2.792,3.01 0.406,0.167 10 false IGE 1.563,0.969 1.885,1.208 0.323,0.24 10 false I49
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator with ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-3 (IGE) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)