Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467512 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B278187  Steering Lock System Missing Message  


DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock actuator with ECU assembly stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B278187 Steering Lock System Missing Message No communication between steering lock actuator with ECU assembly and certification ECU (smart key ECU assembly) for 10 seconds or more.
·

Certification ECU (smart key ECU assembly)

·

Steering lock actuator with ECU assembly

·

Harness or connector


Entry&Start A

WIRING DIAGRAM

B574468E18
0.646,1.375 2.479,1.802 1.833,0.427 10 false Certification ECU (Smart Key ECU Assembly) 0.667,1.24 1.125,1.438 0.458,0.198 10 false I39 1.927,0.927 2.385,1.125 0.458,0.198 10 false LIN 2.281,0.771 2.594,0.969 0.313,0.198 10 false 8 5.26,0.76 5.573,0.958 0.313,0.198 10 false 5 2.719,1.708 3.563,1.948 0.844,0.24 10 false from Battery 4.021,1.583 4.844,1.76 0.823,0.177 10 false STRG LOCK 5.26,1.625 5.417,1.823 0.156,0.198 10 false 7 5.281,3.104 5.438,3.302 0.156,0.198 10 false 1 0.823,4.448 2.458,4.698 1.635,0.25 10 false : LIN Communication Line 5.125,3.74 6.073,3.958 0.948,0.219 10 false I49 5.125,3.917 6.75,4.406 1.625,0.49 10 false Steering Lock Actuator with ECU Assembly 5.479,3.219 5.938,3.417 0.458,0.198 10 false GND 5.479,1.729 5.635,1.927 0.156,0.198 10 false B 5.479,0.906 5.938,1.104 0.458,0.198 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry & Start (CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK FOR DTC
a.

Clear DTCs.

Body Electrical > Entry&Start > Clear DTCs
50002 440

b.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 440

Result:
Result Proceed to
DTC B278187 and B278588 are output A
DTC B278187 and B278588 are not output B
Only DTC 278187 is output C



A

B

C

2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR WITH ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the I49 steering lock actuator with ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I49)Location & Routing

Click Connector(I49)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Steering Lock Actuator or Upper Bracket Assembly

I49-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ACTUATOR WITH ECU ASSEMBLY)
a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the I49 steering lock actuator with ECU assembly connector.



Result:
Proceed to
OK
NG



OK

REPLACE STEERING LOCK ACTUATOR WITH ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR