Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467512 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B120687  P/W Master SW System Missing Message  B124987  Double Locking System Missing Message  B127387  Sliding Roof System Missing Message  B232187  D-Door P/W System Missing Message  B232287  P-Door P/W System Missing Message  B232387  RR-Door P/W System Missing Message  B232487  RL-Door P/W System Missing Message  


DESCRIPTION

This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and multiplex network master switch assembly, front power window regulator motor assembly LH, front power window regulator motor assembly RH, rear power window regulator motor assembly RH, rear power window regulator motor assembly LH, sliding roof ECU (sliding roof drive gear assembly)*1 or double lock door control relay assembly*2 stops for 10 seconds or more.

*1: w/ Sliding Roof System

*2: w/ Double Locking System


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B120687 P/W Master SW System Missing Message No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Harness or connector


Main Body A
B124987 Double Locking System Missing Message No communication between double lock door control relay assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Double lock door control relay assembly

·

Harness or connector


Main Body A
B127387 Sliding Roof System Missing Message No communication between sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Sliding roof ECU (sliding roof drive gear assembly) (w/ Sliding Roof System)

·

Harness or connector


Main Body A
B232187 D-Door P/W System Missing Message
·

No communication between front power window regulator motor assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more. (for LHD)

·

No communication between front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more. (for RHD)


·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Front power window regulator motor assembly LH (for LHD)

·

Front power window regulator motor assembly RH (for RHD)

·

Harness or connector


Main Body A
B232287 P-Door P/W System Missing Message
·

No communication between front power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more. (for LHD)

·

No communication between front power window regulator motor assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more. (for RHD)


·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Front power window regulator motor assembly RH (for LHD)

·

Front power window regulator motor assembly LH (for RHD)

·

Harness or connector


Main Body A
B232387 RR-Door P/W System Missing Message No communication between rear power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Rear power window regulator motor assembly RH

·

Harness or connector


Main Body A
B232487 RL-Door P/W System Missing Message No communication between rear power window regulator motor assembly LH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Rear power window regulator motor assembly LH

·

Harness or connector


Main Body A

WIRING DIAGRAM

C436211E05
0.167,1.646 0.479,1.844 0.313,0.198 10 false MB 0.156,1.823 1.385,2.375 1.229,0.552 10 false Main Body ECU (Multiplex Network Body ECU) 1.156,1.229 1.469,1.427 0.313,0.198 10 false LIN2 1.563,1.052 1.875,1.25 0.313,0.198 10 false 15 1.646,1.667 2.906,2.052 1.26,0.385 10 false Power Distribution Box Assembly 2.698,1.219 3.01,1.417 0.313,0.198 10 false 5B 2.698,0.969 3.01,1.167 0.313,0.198 10 false 37 2.698,0.635 3.01,0.833 0.313,0.198 10 false 5F 2.708,0.375 3.021,0.573 0.313,0.198 10 false 17 0.698,2.76 1.542,3.063 0.844,0.302 10 false from Battery 0.698,4.698 1.594,4.969 0.896,0.271 10 false from Battery 1.729,4.552 2.969,4.844 1.24,0.292 10 false ECU-DCC NO.2*2 1.802,2.646 2.813,2.927 1.01,0.281 10 false S/ROOF*1 2.927,3.354 3.938,3.635 1.01,0.281 10 false d19 2.188,3.542 5.698,3.917 3.51,0.375 10 false Sliding Roof ECU (Sliding Roof Drive Gear Assembly)*1 3.26,3.177 4.271,3.458 1.01,0.281 10 false E 3.25,2.76 4.26,3.042 1.01,0.281 10 false B 3.083,2.677 4.094,2.958 1.01,0.281 10 false 1 3.083,3.094 4.094,3.375 1.01,0.281 10 false 2 3.927,2.99 4.938,3.271 1.01,0.281 10 false MPX 4.365,2.844 5.375,3.125 1.01,0.281 10 false 7 3.896,4.906 4.906,5.188 1.01,0.281 10 false MPX1 4.365,4.719 5.375,5 1.01,0.281 10 false 9 3.25,5.115 4.26,5.396 1.01,0.281 10 false GND 3.25,4.688 4.26,4.969 1.01,0.281 10 false CPUB 2.906,5.313 4.021,5.604 1.115,0.292 10 false I152 2.917,5.479 4.573,5.896 1.656,0.417 10 false Double Lock Door Control Relay Assembly*2 0.125,5.719 2.615,6.094 2.49,0.375 10 false *1: w/ Sliding Roof System 0.135,6.073 2.625,6.448 2.49,0.375 10 false *2: w/ Double Locking System 0.677,6.448 3.167,6.823 2.49,0.375 10 false : LIN Communication Line 3.021,4.604 4.031,4.885 1.01,0.281 10 false 11 3.083,4.99 4.094,5.271 1.01,0.281 10 false 7

C458681E01
2.969,1.167 3.26,1.385 0.292,0.219 10 false N3 2.969,1.323 4.563,1.854 1.594,0.531 10 false Multiplex Network Master Switch Assembly 3.99,0.615 4.344,0.844 0.354,0.229 10 false LIN1 3.979,1 4.333,1.229 0.354,0.229 10 false LIN2 4.354,0.844 4.708,1.073 0.354,0.229 10 false 16 4.365,0.427 4.719,0.656 0.354,0.229 10 false 17 3.25,1 3.604,1.229 0.354,0.229 10 false GND 3.25,0.604 3.74,0.833 0.49,0.229 10 false B 3.031,0.469 3.385,0.698 0.354,0.229 10 false 11 3.021,0.854 3.375,1.083 0.354,0.229 10 false 12 1.813,0.438 2.677,0.688 0.865,0.25 10 false ECU-B NO.3 1.771,5.167 2.635,5.417 0.865,0.25 10 false DOOR R/L 2.938,4.344 3.229,4.563 0.292,0.219 10 false M7 2.938,4.5 4.885,4.896 1.948,0.396 10 false Front Power Window Regulator Motor Assembly RH 4.031,4.01 4.385,4.24 0.354,0.229 10 false LIN 4.344,3.854 4.698,4.083 0.354,0.229 10 false 9 3.281,2.594 3.635,2.823 0.354,0.229 10 false GND 3.063,2.458 3.417,2.688 0.354,0.229 10 false 1 3.271,2.219 3.625,2.448 0.354,0.229 10 false B 3.083,2.083 3.438,2.313 0.354,0.229 10 false 2 1.854,3.656 2.719,3.906 0.865,0.25 10 false DOOR F/L 3.26,4.177 3.615,4.406 0.354,0.229 10 false GND 3.063,4.094 3.417,4.323 0.354,0.229 10 false 1 3.271,3.771 3.625,4 0.354,0.229 10 false B 3.073,3.719 3.427,3.948 0.354,0.229 10 false 2 4.052,2.427 4.406,2.656 0.354,0.229 10 false LIN 4.375,2.219 4.729,2.448 0.354,0.229 10 false 9 2.958,2.979 4.958,3.51 2,0.531 10 false Front Power Window Regulator Motor Assembly LH 2.979,2.792 3.271,3.01 0.292,0.219 10 false N5 2.99,6.115 4.958,6.635 1.969,0.521 10 false Rear Power Window Regulator Motor Assembly LH 3,5.969 3.292,6.188 0.292,0.219 10 false P4 3.25,5.719 3.604,5.948 0.354,0.229 10 false GND 3.26,5.354 3.615,5.583 0.354,0.229 10 false B 3.094,5.271 3.448,5.5 0.354,0.229 10 false 2 4.042,5.542 4.396,5.771 0.354,0.229 10 false LIN 4.354,5.385 4.708,5.615 0.354,0.229 10 false 9 1.833,6.948 2.698,7.198 0.865,0.25 10 false DOOR R/R 3.073,5.635 3.427,5.865 0.354,0.229 10 false 1 1.875,2.042 2.74,2.292 0.865,0.25 10 false DOOR F/R 2.969,7.719 3.26,7.938 0.292,0.219 10 false O4 2.969,7.885 4.875,8.354 1.906,0.469 10 false Rear Power Window Regulator Motor Assembly RH 4.042,7.281 4.396,7.51 0.354,0.229 10 false LIN 4.344,7.135 4.698,7.365 0.354,0.229 10 false 9 3.25,7.5 3.604,7.729 0.354,0.229 10 false GND 3.073,7.385 3.427,7.615 0.354,0.229 10 false 1 3.26,7.083 3.615,7.313 0.354,0.229 10 false B 3.094,6.958 3.448,7.188 0.354,0.229 10 false 2 0.635,8.219 2.49,8.51 1.854,0.292 10 false : LIN Communication Line 0.688,0.583 1.563,0.865 0.875,0.281 10 false from Battery 0.063,0.073 1.042,0.406 0.979,0.333 12 false for LHD: 0.688,2.198 1.594,2.469 0.906,0.271 10 false from Battery 0.688,3.792 1.635,4.063 0.948,0.271 10 false from Battery 0.688,5.375 1.615,5.635 0.927,0.26 10 false from Battery 0.698,7.104 1.635,7.375 0.938,0.271 10 false from Battery

C458681E02
2.969,1.167 3.26,1.385 0.292,0.219 10 false M4 2.969,1.323 4.563,1.854 1.594,0.531 10 false Multiplex Network Master Switch Assembly 3.99,0.615 4.344,0.844 0.354,0.229 10 false LIN1 3.979,1 4.333,1.229 0.354,0.229 10 false LIN2 4.354,0.844 4.708,1.073 0.354,0.229 10 false 16 4.365,0.427 4.719,0.656 0.354,0.229 10 false 17 3.25,1 3.604,1.229 0.354,0.229 10 false GND 3.25,0.604 3.74,0.833 0.49,0.229 10 false B 3.031,0.469 3.385,0.698 0.354,0.229 10 false 11 3.021,0.854 3.375,1.083 0.354,0.229 10 false 12 1.833,0.427 2.698,0.677 0.865,0.25 10 false ECU-B NO.3 1.771,5.167 2.635,5.417 0.865,0.25 10 false DOOR R/L 2.938,4.344 3.229,4.563 0.292,0.219 10 false N6 2.938,4.5 4.885,4.896 1.948,0.396 10 false Front Power Window Regulator Motor Assembly LH 4.031,4.01 4.385,4.24 0.354,0.229 10 false LIN 4.344,3.854 4.698,4.083 0.354,0.229 10 false 9 3.281,2.594 3.635,2.823 0.354,0.229 10 false GND 3.063,2.458 3.417,2.688 0.354,0.229 10 false 1 3.271,2.219 3.625,2.448 0.354,0.229 10 false B 3.083,2.083 3.438,2.313 0.354,0.229 10 false 2 1.854,3.656 2.719,3.906 0.865,0.25 10 false DOOR F/L 3.26,4.177 3.615,4.406 0.354,0.229 10 false GND 3.063,4.094 3.417,4.323 0.354,0.229 10 false 1 3.271,3.771 3.625,4 0.354,0.229 10 false B 3.073,3.719 3.427,3.948 0.354,0.229 10 false 2 4.052,2.427 4.406,2.656 0.354,0.229 10 false LIN 4.375,2.219 4.729,2.448 0.354,0.229 10 false 9 2.958,2.979 4.958,3.51 2,0.531 10 false Front Power Window Regulator Motor Assembly RH 2.979,2.792 3.271,3.01 0.292,0.219 10 false M6 2.99,6.115 4.958,6.635 1.969,0.521 10 false Rear Power Window Regulator Motor Assembly LH 3,5.969 3.292,6.188 0.292,0.219 10 false P4 3.25,5.719 3.604,5.948 0.354,0.229 10 false GND 3.26,5.354 3.615,5.583 0.354,0.229 10 false B 3.094,5.271 3.448,5.5 0.354,0.229 10 false 2 4.042,5.542 4.396,5.771 0.354,0.229 10 false LIN 4.354,5.385 4.708,5.615 0.354,0.229 10 false 9 1.833,6.948 2.698,7.198 0.865,0.25 10 false DOOR R/R 3.073,5.635 3.427,5.865 0.354,0.229 10 false 1 1.875,2.042 2.74,2.292 0.865,0.25 10 false DOOR F/R 2.969,7.719 3.26,7.938 0.292,0.219 10 false O4 2.969,7.885 4.875,8.354 1.906,0.469 10 false Rear Power Window Regulator Motor Assembly RH 4.042,7.281 4.396,7.51 0.354,0.229 10 false LIN 4.344,7.135 4.698,7.365 0.354,0.229 10 false 9 3.25,7.5 3.604,7.729 0.354,0.229 10 false GND 3.073,7.385 3.427,7.615 0.354,0.229 10 false 1 3.26,7.083 3.615,7.313 0.354,0.229 10 false B 3.094,6.958 3.448,7.188 0.354,0.229 10 false 2 0.635,8.219 2.49,8.51 1.854,0.292 10 false : LIN Communication Line 0.688,0.583 1.563,0.865 0.875,0.281 10 false from Battery 0.063,0.073 1.042,0.406 0.979,0.333 12 false for RHD: 0.688,2.198 1.594,2.469 0.906,0.271 10 false from Battery 0.688,3.792 1.635,4.063 0.948,0.271 10 false from Battery 0.688,5.375 1.615,5.635 0.927,0.26 10 false from Battery 0.698,7.104 1.635,7.375 0.938,0.271 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION



PROCEDURE

1.CHECK FOR VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR DTC

B

22.CHECK FOR DTC
2.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

b.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to

*1: w/ Double Locking System

*2: w/ Sliding Roof System

DTC B120687, B124987*1, B127387*2, B232187, B232287, B232387 and B232487 are all output A
Within DTC B120687, B124987*1, B127387*2, B232187, B232287, B232387 and B232487 one or more DTCs are output B
DTC is not output C



A

3.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

B

4.CHECK FOR DTC

C

3.INSPECT POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

C435656C02
1.875,0.333 2.292,0.583 0.417,0.25 5.5,0.083 5.917,0.333 0.417,0.25 2.5,1.396 2.313,1.396 2.313,1.396 2.313,0.927 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 2,0.385 2.313,0.542 0.313,0.156 10 false MB 5.635,0.135 5.948,0.292 0.313,0.156 10 false 5B 2.563,1.323 2.979,1.5 0.417,0.177 10 false LIN2
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5B-37 - MB-15 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

4.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to

*1: w/ Double Locking System

*2: w/ Sliding Roof System

DTC B120687, B124987*1, B127387*2, B232187, B232287 and B232487 are output A
Only DTCs B120687 and B232187 are output B
Only DTC B120687 is output C
Only DTC B124987 is output*1 D
Only DTC B127387 is output*2 E
Only DTC B232187 is output F
Only DTC B232287 is output G
Only DTC B232387 is output H
Only DTC B232487 is output I



A

5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

B

6.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

C

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY POWER SOURCE CIRCUIT)

D

8.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)

E

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))

F

12.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

G

15.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

H

17.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

I

20.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
5.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the N3 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Body>Front Door Wire LH>Multiplex Network Master Switch Assembly

5B-37 - N3-17 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the N3 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Body>Front Door Wire LH>Multiplex Network Master Switch Assembly

5B-37 - N3-17 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the N3 multiplex network master switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Body>Front Door Wire LH>Multiplex Network Master Switch Assembly

N3-11 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Body>Front Door Wire LH>Multiplex Network Master Switch Assembly

N3-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the I152 double lock door control relay assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I152)Location & Routing

Click Connector(I152)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Double Lock Door Control Relay Assembly

5B-37 - I152-9 (MPX1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the I152 double lock door control relay assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I152)Location & Routing

Click Connector(I152)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Double Lock Door Control Relay Assembly

I152-11 (CPUB) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I152)Location & Routing

Click Connector(I152)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Double Lock Door Control Relay Assembly

I152-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d19)Location & Routing

Click Connector(d19)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Assembly)

5B-37 - d19-7 (MPX) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) POWER SOURCE CIRCUIT)
a.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(d19)Location & Routing

Click Connector(d19)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Assembly)

d19-1 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d19)Location & Routing

Click Connector(d19)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Assembly)

d19-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the N5 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N5)Location & Routing

Click Connector(N5)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

5B-37 - N5-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH POWER SOURCE CIRCUIT)

NG

14.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
13.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH POWER SOURCE CIRCUIT)
a.

Disconnect the N5 front power window regulator motor assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(N5)Location & Routing

Click Connector(N5)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

N5-2 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N5)Location & Routing

Click Connector(N5)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

N5-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the N3 multiplex network master switch assembly connector.


b.

Disconnect the N5 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3,N5)Location & Routing

Click Connector(N3)Body>Front Door Wire LH>Multiplex Network Master Switch Assembly

Click Connector(N5)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

N3-16 (LIN2) - N5-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the M7 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M7)Location & Routing

Click Connector(M7)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

5B-37 - M7-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH POWER SOURCE CIRCUIT)
a.

Disconnect the M7 front power window regulator motor assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(M7)Location & Routing

Click Connector(M7)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

M7-2 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M7)Location & Routing

Click Connector(M7)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

M7-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Reconnect the 5F power distribution box assembly connector.


b.

Disconnect the O4 rear power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

5F-17 - O4-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH POWER SOURCE CIRCUIT)

NG

19.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
18.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH POWER SOURCE CIRCUIT)
a.

Disconnect the O4 rear power window regulator motor assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

O4-2 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

O4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the 5F power distribution box assembly connector.


b.

Disconnect the O4 rear power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

5F-17 - O4-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the P4 rear power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(P4)Location & Routing

Click Connector(P4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

5B-37 - P4-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH POWER SOURCE CIRCUIT)
a.

Disconnect the P4 rear power window regulator motor assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(P4)Location & Routing

Click Connector(P4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

P4-2 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(P4)Location & Routing

Click Connector(P4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

P4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

b.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to

*1: w/ Double Locking System

*2: w/ Sliding Roof System

DTC B120687, B124987*1, B127387*2, B232187, B232287, B232387 and B232487 are all output A
Within DTC B120687, B124987*1, B127387*2, B232187, B232287, B232387 and B232487 one or more DTCs are output B
DTC is not output C



A

23.INSPECT POWER DISTRIBUTION BOX ASSEMBLY

B

24.CHECK FOR DTC

C

23.INSPECT POWER DISTRIBUTION BOX ASSEMBLY
a.

Remove the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL

C435656C02
1.875,0.333 2.292,0.583 0.417,0.25 5.5,0.083 5.917,0.333 0.417,0.25 2.5,1.396 2.313,1.396 2.313,1.396 2.313,0.927 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a 2,0.385 2.313,0.542 0.313,0.156 10 false MB 5.635,0.135 5.948,0.292 0.313,0.156 10 false 5B 2.563,1.323 2.979,1.5 0.417,0.177 10 false LIN2
*a Component without harness connected
(Power Distribution Box Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5B-37 - MB-15 (LIN2) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

24.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to

*1: w/ Double Locking System

*2: w/ Sliding Roof System

DTC B120687, B124987*1, B127387*2, B232187, B232287 and B232487 are output A
Only DTCs B120687 and B232187 are output B
Only DTC B120687 is output C
Only DTC B124987 is output*1 D
Only DTC B127387 is output*2 E
Only DTC B232187 is output F
Only DTC B232287 is output G
Only DTC B232387 is output H
Only DTC B232487 is output I



A

25.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

B

26.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)

C

27.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY POWER SOURCE CIRCUIT)

D

28.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)

E

30.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))

F

32.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

G

35.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

H

37.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

I

40.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
25.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the N3 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3)Location & Routing

Click Connector(N3)Body>Front Door Wire LH>Multiplex Network Master Switch Assembly

5B-37 - N3-17 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the M4 multiplex network master switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M4)Location & Routing

Click Connector(M4)Body>Front Door Wire RH>Multiplex Network Master Switch Assembly

5B-37 - M4-17 (LIN1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the M4 multiplex network master switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(M4)Location & Routing

Click Connector(M4)Body>Front Door Wire RH>Multiplex Network Master Switch Assembly

M4-11 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M4)Location & Routing

Click Connector(M4)Body>Front Door Wire RH>Multiplex Network Master Switch Assembly

M4-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the I152 double lock door control relay assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I152)Location & Routing

Click Connector(I152)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Double Lock Door Control Relay Assembly

5B-37 - I152-9 (MPX1) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

29.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK HARNESS AND CONNECTOR (DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the I152 double lock door control relay assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(I152)Location & Routing

Click Connector(I152)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Double Lock Door Control Relay Assembly

I152-11 (CPUB) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(I152)Location & Routing

Click Connector(I152)Instrument Panel>Instrument Panel Wire / Mobile Wireless Charger Cord / No. 1 Navigation Wire / No. 2 Instrument Panel Wire / No. 5 Instrument Panel Wire / Telephone Computer Wire>Double Lock Door Control Relay Assembly

I152-7 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d19)Location & Routing

Click Connector(d19)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Assembly)

5B-37 - d19-7 (MPX) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

31.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) POWER SOURCE CIRCUIT)
a.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(d19)Location & Routing

Click Connector(d19)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Assembly)

d19-1 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(d19)Location & Routing

Click Connector(d19)Body>No. 1 Roof Wire>Sliding Roof Control ECU (Sliding Roof Drive Gear Assembly)

d19-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

32.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the M6 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M6)Location & Routing

Click Connector(M6)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

5B-37 - M6-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

33.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH POWER SOURCE CIRCUIT)

NG

34.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
33.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH POWER SOURCE CIRCUIT)
a.

Disconnect the M6 front power window regulator motor assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(M6)Location & Routing

Click Connector(M6)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

M6-2 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M6)Location & Routing

Click Connector(M6)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

M6-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the M4 multiplex network master switch assembly connector.


b.

Disconnect the M6 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M4,M6)Location & Routing

Click Connector(M4)Body>Front Door Wire RH>Multiplex Network Master Switch Assembly

Click Connector(M6)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

M4-16 (LIN2) - M6-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the M6 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M6)Location & Routing

Click Connector(M6)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

5B-37 - M6-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

36.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

36.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH POWER SOURCE CIRCUIT)
a.

Disconnect the N6 front power window regulator motor assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(N6)Location & Routing

Click Connector(N6)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

N6-2 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N6)Location & Routing

Click Connector(N6)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

N6-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Reconnect the 5F power distribution box assembly connector.


b.

Disconnect the O4 rear power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

5F-17 - O4-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

38.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH POWER SOURCE CIRCUIT)

NG

39.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
38.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH POWER SOURCE CIRCUIT)
a.

Disconnect the O4 rear power window regulator motor assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

O4-2 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

O4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

39.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the 5F power distribution box assembly connector.


b.

Disconnect the O4 rear power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(O4)Location & Routing

Click Connector(O4)Body>No. 1 Rear Door Wire>Rear Power Window Regulator Motor Assembly RH

5F-17 - O4-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.CHECK HARNESS AND CONNECTOR (POWER DISTRIBUTION BOX ASSEMBLY - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the 5B power distribution box assembly connector.


b.

Disconnect the P4 rear power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(P4)Location & Routing

Click Connector(P4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

5B-37 - P4-9 (LIN) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

41.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

41.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH POWER SOURCE CIRCUIT)
a.

Disconnect the P4 rear power window regulator motor assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

Click Location & Routing(P4)Location & Routing

Click Connector(P4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

P4-2 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(P4)Location & Routing

Click Connector(P4)Body>No. 2 Rear Door Wire>Rear Power Window Regulator Motor Assembly LH

P4-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR