Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467512 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B232588  Door LIN Bus off  


DESCRIPTION

The main body ECU (multiplex network body ECU) intermittently monitors the LIN communication bus between the components related to the doors. DTC B232588 is stored when a malfunction in the LIN communication bus between the components related to the doors is detected consecutively 3 times.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Priority
B232588 Door LIN Bus off The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more.
·

Main body ECU (multiplex network body ECU)

·

Power distribution box assembly

·

Multiplex network master switch assembly

·

Front power window regulator motor assembly LH

·

Front power window regulator motor assembly RH

·

Rear power window regulator motor assembly LH

·

Rear power window regulator motor assembly RH

·

Double lock door control relay assembly (w/ Double Looking System)

·

Sliding roof drive gear assembly (w/ Sliding Roof System)

·

Harness or connector


Main Body A

WIRING DIAGRAM

for LHD
C458682E01
1.323,2.26 1.563,2.479 0.24,0.219 10 false LIN 1.25,0.823 1.625,1.021 0.375,0.198 10 false LIN2 5.396,1.115 5.781,1.323 0.385,0.208 10 false LIN2 5.417,5.156 5.656,5.375 0.24,0.219 10 false LIN 1.323,3.698 1.896,4.042 0.573,0.344 10 false LIN 5.385,3.635 5.625,3.854 0.24,0.219 10 false LIN 5.438,2.396 7.094,2.875 1.656,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 0.177,2.708 2.208,3.146 2.031,0.438 10 false Front Power Window Regulator Motor Assembly LH 0.208,1.167 1.854,1.698 1.646,0.531 10 false Multiplex Network Master Switch Assembly 0.125,4.167 2.083,4.656 1.958,0.49 10 false Front Power Window Regulator Motor Assembly RH 4.885,4.167 6.792,4.75 1.906,0.583 10 false Rear Power Window Regulator Motor Assembly RH 4.896,5.667 6.844,6.094 1.948,0.427 10 false Rear Power Window Regulator Motor Assembly LH 1.271,0.531 1.615,0.75 0.344,0.219 10 false LIN1 0.646,8.396 2.573,8.698 1.927,0.302 10 false : LIN Communication Line 0.208,1.021 0.646,1.271 0.438,0.25 10 false N3 0.208,2.531 0.823,2.844 0.615,0.313 10 false N5 4.906,5.49 5.823,5.76 0.917,0.271 10 false P4 0.146,3.948 0.583,4.198 0.438,0.25 10 false M7 4.896,3.938 5.333,4.188 0.438,0.25 10 false O4 5.427,2.219 5.865,2.469 0.438,0.25 10 false MB 4.063,0.542 4.5,0.792 0.438,0.25 10 false 5B 5.146,0.958 5.583,1.208 0.438,0.25 10 false 15 4.052,0.927 4.49,1.177 0.438,0.25 10 false 17 1.615,0.344 2.052,0.594 0.438,0.25 10 false 17 5.208,3.49 5.646,3.74 0.438,0.25 10 false 9 1.615,2.115 2.052,2.365 0.438,0.25 10 false 9 5.219,5.052 5.656,5.302 0.438,0.25 10 false 9 1.615,3.542 2.052,3.792 0.438,0.25 10 false 9 1.615,0.677 2.052,0.927 0.438,0.25 10 false 16 4.063,1.135 4.5,1.385 0.438,0.25 10 false 5F 4.063,0.302 4.5,0.552 0.438,0.25 10 false 37 0.125,5.427 0.563,5.677 0.438,0.25 10 false d19 0.135,5.625 2.063,6.031 1.927,0.406 10 false Slide Roof ECU (Sliding Roof Drive Gear Assembly)*1 1.24,5.219 1.677,5.469 0.438,0.25 10 false MPX 5.396,6.698 5.938,6.969 0.542,0.271 10 false MPX1 5.208,6.531 5.646,6.781 0.438,0.25 10 false 9 4.083,2.104 5.313,2.552 1.229,0.448 10 false Power Distribution Box Assembly 0.156,8.052 2.833,8.323 2.677,0.271 10 false *1: w/ Sliding Roof System 1.656,5.031 2.094,5.281 0.438,0.25 10 false 7 4.969,6.927 5.406,7.177 0.438,0.25 10 false I152 5,7.104 6.594,7.542 1.594,0.438 10 false Double Lock Door Control Relay Assembly*2 2.625,8.052 5.302,8.323 2.677,0.271 10 false *2: w/ Double Locking System

for RHD
C458682E02
1.323,2.26 1.563,2.479 0.24,0.219 10 false LIN 1.25,0.823 1.625,1.021 0.375,0.198 10 false LIN2 5.396,1.115 5.781,1.323 0.385,0.208 10 false LIN2 5.417,5.156 5.656,5.375 0.24,0.219 10 false LIN 1.323,3.698 1.896,4.042 0.573,0.344 10 false LIN 5.385,3.635 5.625,3.854 0.24,0.219 10 false LIN 5.438,2.396 7.094,2.875 1.656,0.479 10 false Main Body ECU (Multiplex Network Body ECU) 0.115,4.135 2.146,4.573 2.031,0.438 10 false Front Power Window Regulator Motor Assembly LH 0.208,1.167 1.854,1.698 1.646,0.531 10 false Multiplex Network Master Switch Assembly 0.135,2.75 2.094,3.24 1.958,0.49 10 false Front Power Window Regulator Motor Assembly RH 4.885,4.167 6.792,4.75 1.906,0.583 10 false Rear Power Window Regulator Motor Assembly RH 4.896,5.667 6.844,6.094 1.948,0.427 10 false Rear Power Window Regulator Motor Assembly LH 1.271,0.531 1.615,0.75 0.344,0.219 10 false LIN1 0.646,8.396 2.573,8.698 1.927,0.302 10 false : LIN Communication Line 0.208,1.021 0.646,1.271 0.438,0.25 10 false M4 0.115,3.969 0.729,4.281 0.615,0.313 10 false N6 4.906,5.49 5.823,5.76 0.917,0.271 10 false P4 0.135,2.552 0.573,2.802 0.438,0.25 10 false M6 4.896,3.938 5.333,4.188 0.438,0.25 10 false O4 5.427,2.219 5.865,2.469 0.438,0.25 10 false MB 4.063,0.542 4.5,0.792 0.438,0.25 10 false 5B 5.146,0.958 5.583,1.208 0.438,0.25 10 false 15 4.052,0.927 4.49,1.177 0.438,0.25 10 false 17 1.615,0.344 2.052,0.594 0.438,0.25 10 false 17 5.208,3.49 5.646,3.74 0.438,0.25 10 false 9 1.615,2.115 2.052,2.365 0.438,0.25 10 false 9 5.219,5.052 5.656,5.302 0.438,0.25 10 false 9 1.615,3.542 2.052,3.792 0.438,0.25 10 false 9 1.615,0.677 2.052,0.927 0.438,0.25 10 false 16 4.063,1.135 4.5,1.385 0.438,0.25 10 false 5F 4.063,0.302 4.5,0.552 0.438,0.25 10 false 37 0.125,5.427 0.563,5.677 0.438,0.25 10 false d19 0.135,5.625 2.063,6.031 1.927,0.406 10 false Slide Roof ECU (Sliding Roof Drive Gear Assembly)*1 1.24,5.219 1.677,5.469 0.438,0.25 10 false MPX 5.396,6.698 5.875,6.99 0.479,0.292 10 false MPX1 5.208,6.531 5.646,6.781 0.438,0.25 10 false 9 4.083,2.104 5.313,2.552 1.229,0.448 10 false Power Distribution Box Assembly 0.156,8.052 2.833,8.323 2.677,0.271 10 false *1: w/ Sliding Roof System 1.656,5.031 2.094,5.281 0.438,0.25 10 false 7 4.969,6.927 5.406,7.177 0.438,0.25 10 false I152 5,7.104 6.594,7.542 1.594,0.438 10 false Double Lock Door Control Relay Assembly*2 2.625,8.052 5.302,8.323 2.677,0.271 10 false *2: w/ Double Locking System

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off to troubleshoot:

Connect the GTS to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

When the front power window regulator motor assembly LH*1 or RH*2 is removed and reinstalled or replaced, the front power window regulator motor assembly LH*1 or RH*2 must be initialized.

*1: for LHD

*2: for RHD


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE



PROCEDURE

1.CHECK FOR VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FOR DTC

B

15.CHECK FOR DTC
2.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

b.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232588 is not output B



A

3.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

3.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the N5 front power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232187 is output B



A

4.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

4.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Disconnect the N3 multiplex network master switch assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTCs B120687 and B232187 are output B



A

5.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

B

13.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
5.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the M7 front power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232287 is output B



A

6.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

6.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the O4 rear power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232387 is output B



A

7.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

7.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the P4 rear power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232487 is output B



A

8.CHECK FOR VEHICLE TYPE

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

8.CHECK FOR VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
Vehicle type with sliding roof system A
Vehicle type without sliding roof system B



A

9.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

B

10.CHECK FOR VEHICLE TYPE
9.CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
a.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B127387 is output B



A

10.CHECK FOR VEHICLE TYPE

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

10.CHECK FOR VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
Vehicle type with double locking system A
Vehicle type without double locking system B



A

11.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

B

12.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
11.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
a.

Disconnect the I152 double lock door control relay assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B124987 is output B



A

12.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

B

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


b.

Reconnect the power distribution box assembly connectors.


c.

Disconnect the N5 front power window regulator motor assembly LH connector.


d.

Disconnect the M7 front power window regulator motor assembly RH connector.


e.

Disconnect the P4 rear power window regulator motor assembly LH connector.


f.

Disconnect the O4 rear power window regulator motor assembly RH connector.


g.

w/ Sliding Roof System:

i.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.



h.

w/ Double Locking System:

i.

Disconnect the I152 double lock door control relay assembly connector.



i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-15 (LIN2) - Body ground Always 10 kΩ or higher
MB-15 (LIN2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

14.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
13.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the N3 multiplex network master switch assembly connector.


b.

Disconnect the N5 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N3,N5)Location & Routing

Click Connector(N3)Body>Front Door Wire LH>Multiplex Network Master Switch Assembly

Click Connector(N5)Body>Front Door Wire LH>Front Power Window Regulator Motor Assembly LH

N3-16 (LIN2) - N5-9 (LIN) Always Below 1 Ω
N3-16 (LIN2) or N5-9 (LIN) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
a.

Disconnect the 5B and 5F power distribution box assembly connectors.


b.

Disconnect the N5 front power window regulator motor assembly LH connector.


c.

Disconnect the M7 front power window regulator motor assembly RH connector.


d.

Disconnect the P4 rear power window regulator motor assembly LH connector.


e.

Disconnect the O4 rear power window regulator motor assembly RH connector.


f.

w/ Sliding Roof System:

i.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.



g.

w/ Double Locking System:

i.

Disconnect the I152 double lock door control relay assembly connector.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5F-17 - Body ground Always 10 kΩ or higher
5B-37 - Body ground Always 10 kΩ or higher
5F-17 - Other terminals Always 10 kΩ or higher
5B-37 - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

b.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232588 is not output B



A

16.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

B

16.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the M6 front power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232187 is output B



A

17.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

17.CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Disconnect the M4 multiplex network master switch assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTCs B120687 and B232187 are output B



A

18.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

26.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
18.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the N6 front power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232287 is output B



A

19.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

19.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the O4 rear power window regulator motor assembly RH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232387 is output B



A

20.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

20.CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the P4 rear power window regulator motor assembly LH connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B232487 is output B



A

21.CHECK FOR VEHICLE TYPE

B

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

21.CHECK FOR VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
Vehicle type with sliding roof system A
Vehicle type without sliding roof system B



A

22.CHECK SLIDING ROOF DRIVE GEAR ASSEMBLY

B

23.CHECK FOR VEHICLE TYPE
22.CHECK SLIDING ROOF DRIVE GEAR ASSEMBLY
a.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B127387 is output B



A

23.CHECK FOR VEHICLE TYPE

B

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)

23.CHECK FOR VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
Vehicle type with double locking system A
Vehicle type without double locking system B



A

24.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

B

25.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
24.CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY
a.

Disconnect the I152 double lock door control relay assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 449

c.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 449

Result:
Result Proceed to
DTC B232588 is output A
DTC B124987 is output B



A

25.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)

B

REPLACE DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY

25.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


b.

Reconnect the power distribution box assembly connectors.


c.

Disconnect the N6 front power window regulator motor assembly LH connector.


d.

Disconnect the M6 front power window regulator motor assembly RH connector.


e.

Disconnect the P4 rear power window regulator motor assembly LH connector.


f.

Disconnect the O4 rear power window regulator motor assembly RH connector.


g.

w/ Sliding Roof System:

i.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.



h.

w/ Double Locking System:

i.

Disconnect the I152 double lock door control relay assembly connector.



i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-15 (LIN2) - Body ground Always 10 kΩ or higher
MB-15 (LIN2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

27.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
26.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the M4 multiplex network master switch assembly connector.


b.

Disconnect the M6 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M4,M6)Location & Routing

Click Connector(M4)Body>Front Door Wire RH>Multiplex Network Master Switch Assembly

Click Connector(M6)Body>Front Door Wire RH>Front Power Window Regulator Motor Assembly RH

M4-16 (LIN2) - M6-9 (LIN) Always Below 1 Ω
M4-16 (LIN2) or M6-9 (LIN) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK HARNESS AND CONNECTOR (LIN BUS CIRCUIT)
a.

Disconnect the 5B and 5F power distribution box assembly connectors.


b.

Disconnect the N6 front power window regulator motor assembly LH connector.


c.

Disconnect the M6 front power window regulator motor assembly RH connector.


d.

Disconnect the P4 rear power window regulator motor assembly LH connector.


e.

Disconnect the O4 rear power window regulator motor assembly RH connector.


f.

w/ Sliding Roof System:

i.

Disconnect the d19 sliding roof ECU (sliding roof drive gear assembly) connector.



g.

w/ Double Locking System:

i.

Disconnect the I152 double lock door control relay assembly connector.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5F-17 - Body ground Always 10 kΩ or higher
5B-37 - Body ground Always 10 kΩ or higher
5F-17 - Other terminals Always 10 kΩ or higher
5B-37 - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER DISTRIBUTION BOX ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR