Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM38G0E _57 Power Source / Network _100626 NETWORKING _0467512 LIN COMMUNICATION SYSTEM U

NETWORKING  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK POWER DISTRIBUTION BOX ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E448686C15
3.458,7.583 3.854,7.885 0.396,0.302 5.594,3.219 6.01,3.458 0.417,0.24 1.146,3.198 1.563,3.438 0.417,0.24 1.219,4.469 1.635,4.708 0.417,0.24 1.458,6.042 1.875,6.281 0.417,0.24 3.615,6.063 4.031,6.302 0.417,0.24 4.385,4.458 4.802,4.698 0.417,0.24 6.375,6.073 6.792,6.313 0.417,0.24 4.719,6.094 5.135,6.333 0.417,0.24 6.208,4.479 6.625,4.719 0.417,0.24 5.49,6.094 5.906,6.333 0.417,0.24 3.469,3.188 3.885,3.427 0.417,0.24 2.219,0.917 2.219,0.698 2.219,0.698 2.385,0.698 true 0.646,1.229 0.927,1.229 true 2.229,1.51 2.469,1.51 true 2.219,1.802 2.458,1.802 true 0.646,2.073 0.885,2.073 true 0.635,2.302 0.875,2.302 true 0.646,2.542 1.125,2.542 true 0.635,1.698 0.917,1.698 true 6.292,1.156 6.573,1.156 true 6.271,1.75 6.552,1.75 true 6.292,2.208 6.573,2.208 true 2.229,2.125 2.469,2.125 true 1.177,0.542 1.177,0.323 1.177,0.323 1.344,0.323 true 4.865,0.563 4.865,0.344 4.865,0.344 5.031,0.344 true 6.146,0.51 6.146,0.292 6.146,0.292 6.313,0.292 true 4.25,0.969 4.719,1.542 0.469,0.573 10 false MB 3.563,7.656 4.063,8.281 0.5,0.625 10 false MB 0.469,1.635 0.781,1.833 0.313,0.198 10 false 5E 0.479,2.031 0.792,2.229 0.313,0.198 10 false 5K 2.521,1.448 2.979,1.646 0.458,0.198 10 false I1 2.51,1.74 2.969,1.938 0.458,0.198 10 false I2 0.448,2.24 0.948,2.469 0.5,0.229 10 false 5J 2.458,0.635 2.917,0.833 0.458,0.198 10 false *2 6.656,1.083 6.969,1.281 0.313,0.198 10 false 5C 6.615,1.677 6.927,1.875 0.313,0.198 10 false 5B 5.75,3.26 6.208,3.458 0.458,0.198 10 false I1 3.615,3.229 4.073,3.427 0.458,0.198 10 false I2 1.344,4.521 1.656,4.719 0.313,0.198 10 false 5C 4.531,4.521 4.844,4.719 0.313,0.198 10 false 5B 1.583,6.094 1.896,6.292 0.313,0.198 10 false 5F 3.74,6.125 4.052,6.323 0.313,0.198 10 false 5E 6.479,6.125 6.792,6.323 0.313,0.198 10 false 5H 4.865,6.146 5.219,6.302 0.354,0.156 10 false 5K 0.448,1.146 1.063,1.344 0.615,0.198 10 false 5F 0.469,2.49 0.969,2.719 0.5,0.229 10 false 5H 6.615,2.135 6.927,2.333 0.313,0.198 10 false 5A 6.344,4.542 6.656,4.74 0.313,0.198 10 false 5A 5.635,6.146 5.948,6.344 0.313,0.198 10 false 5J 2.521,2.063 2.979,2.26 0.458,0.198 10 false I3 1.323,3.25 1.781,3.448 0.458,0.198 10 false I3 1.406,0.24 1.865,0.438 0.458,0.198 10 false *1 5.104,0.25 5.563,0.448 0.458,0.198 10 false *1 6.375,0.188 6.833,0.385 0.458,0.198 10 false *1
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.



b.

Connect the power distribution box assembly connectors.


c.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-13 (GND1) - Body ground Ground Always Below 1 Ω
MB-26 (BECU) - Body ground Battery power supply Always 11 to 14 V
MB-27 (IGR) - Body ground Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
5F-17 - Body ground LIN communication line Ignition switch ON Pulse generation
5B-37 - Body ground LIN communication line Ignition switch ON Pulse generation
I2-11 (LIN4) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


*1: for LHD

*2: for RHD


a.
B290827C08
0.969,0.229 1.385,0.5 0.417,0.271 1.906,0.219 2.323,0.49 0.417,0.271 1.125,0.302 1.583,0.5 0.458,0.198 10 false N3 2.042,0.281 2.5,0.479 0.458,0.198 10 false M4 1.469,0.292 1.927,0.49 0.458,0.198 10 false *A 2.406,0.281 2.865,0.479 0.458,0.198 10 false *B
*A for LHD
*B for RHD


Disconnect the N3*1 or M4*2 multiplex network master switch assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
N3-11 (B) - Body ground Battery power supply Always 11 to 14 V
N3-12 (GND) - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M4-11 (B) - Body ground Battery power supply Always 11 to 14 V
M4-12 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the N3*1 or M4*2 multiplex network master switch assembly connector.


d.

Measure the pulse according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
N3-17 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M4-17 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


*1: for LHD

*2: for RHD


a.
B290829C03
1.75,0.323 2.146,0.583 0.396,0.26 0.844,0.313 1.24,0.573 0.396,0.26 1.865,0.365 2.083,0.542 0.219,0.177 10 false N6 0.99,0.365 1.208,0.542 0.219,0.177 10 false N5 1.281,0.365 1.5,0.542 0.219,0.177 10 false *A 2.208,0.354 2.427,0.531 0.219,0.177 10 false *B
*A for LHD
*B for RHD


Disconnect the N5*1 or N6*2 front power window regulator motor assembly LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
N5-2 (B) - Body ground Battery power supply Always 11 to 14 V
N5-1 (GND) - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
N6-2 (B) - Body ground Battery power supply Always 11 to 14 V
N6-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the N5*1 or N6*2 front power window regulator motor assembly LH connector.


d.

Measure the pulse according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
N5-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
N6-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


*1: for LHD

*2: for RHD


a.
B290829C04
1.75,0.323 2.146,0.583 0.396,0.26 0.844,0.313 1.24,0.573 0.396,0.26 1.865,0.365 2.083,0.542 0.219,0.177 10 false M6 0.99,0.365 1.208,0.542 0.219,0.177 10 false M7 1.281,0.365 1.5,0.542 0.219,0.177 10 false *A 2.208,0.354 2.427,0.531 0.219,0.177 10 false *B
*A for LHD
*B for RHD


Disconnect the M7*1 or M6*2 front power window regulator motor assembly RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M7-2 (B) - Body ground Battery power supply Always 11 to 14 V
M7-1 (GND) - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M6-2 (B) - Body ground Battery power supply Always 11 to 14 V
M6-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the M7*1 or M6*2 front power window regulator motor assembly RH connector.


d.

Measure the pulse according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M7-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
M6-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


a.
B290829N41
1.458,0.323 1.854,0.583 0.396,0.26 1.583,0.365 1.906,0.583 0.323,0.219 10 false P4

Disconnect the P4 rear power window regulator motor assembly LH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
P4-2 (B) - Body ground Battery power supply Always 11 to 14 V
P4-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the L5 rear power window regulator motor assembly LH connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
P4-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH


a.
B290829N42
1.458,0.323 1.854,0.583 0.396,0.26 1.583,0.365 1.802,0.542 0.219,0.177 10 false O4

Disconnect the O4 rear power window regulator motor assembly RH connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
O4-2 (B) - Body ground Battery power supply Ignition switch off 11 to 14 V
O4-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the O4 rear power window regulator motor assembly RH connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
O4-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK SLIDING ROOF DRIVE GEAR ASSEMBLY (w/ Slide Roof System)


a.
B493581N11
1.573,0.219 1.906,0.427 0.333,0.208 1.625,0.25 1.938,0.448 0.313,0.198 10 false d19

Disconnect the d19 sliding roof drive gear assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
d19-1 (B) - Body ground Battery power supply Always 11 to 14 V
d19-2 (E) - Body ground Ground Always Below 1 Ω


c.

Reconnect the d19 sliding roof drive gear assembly connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
d19-7 (MPX1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK DOUBLE LOCK DOOR CONTROL RELAY ASSEMBLY (w/Double Locking System)


B473206N02
3.031,0.135 3.427,0.354 0.396,0.219 3.094,0.167 3.5,0.396 0.406,0.229 10 false I152

a.

Disconnect the I152 double lock door control relay assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I152-11 (CPUB) - Body ground Battery power supply Always 11 to 14 V
I152-12 (+B) - Body ground Battery power supply Always 11 to 14 V
I152-7 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the I152 double lock door control relay assembly connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I152-9 (MPX1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK ENGINE SWITCH (w/ Fingerprint Authentication)


B516200N13
3.385,0.208 3.781,0.458 0.396,0.25 3.479,0.25 3.938,0.448 0.458,0.198 10 false I75

a.

Disconnect the I75 engine switch connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I75-10 (+B) - Body ground Battery power supply Always 11 to 14 V
I75-3 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the I75 engine switch connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I75-4 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B574584N26
4.802,0.406 5.219,0.656 0.417,0.25 4.896,0.458 5.417,0.677 0.521,0.219 10 false I39

a.

Disconnect the I39 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
I39-6 (+B) - Body ground Battery power supply Always 11 to 14 V
I39-29 (E) - Body ground Ground Always Below 1 Ω


c.

Reconnect the I39 certification ECU (smart key ECU assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I39-8 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK STEERING LOCK ACTUATOR WITH ECU ASSEMBLY


B439652N21
3.417,0.313 3.833,0.563 0.417,0.25 3.521,0.354 3.833,0.552 0.313,0.198 10 false I49

a.

Disconnect the I49 steering lock actuator with ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I49-7 (B) - Body ground Battery power supply Always 11 to 14 V
I49-1 (GND) - Body ground Ground Always Below 1 Ω


c.

Reconnect the I49 steering lock actuator with ECU assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I49-5 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK ID CODE BOX (IMMOBILISER CODE ECU)


B463711N07
3.24,0.24 3.677,0.49 0.438,0.25 3.344,0.302 3.802,0.5 0.458,0.198 10 false I66

a.

Disconnect the I66 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
I66-5 (GND) - Body ground Ground Always Below 1 Ω
I66-1 (+B) - Body ground +B power supply Always 11 to 14 V


c.

Reconnect the I66 ID code box (immobiliser code ECU) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
I66-2 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK RAIN SENSOR


E379797N16
3.438,0.177 3.781,0.385 0.344,0.208 3.5,0.208 3.969,0.469 0.469,0.26 10 false d23

a.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
d23-3 (MPX) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK MAP LIGHT ASSEMBLY


C458691N01
3.448,0.115 3.865,0.354 0.417,0.24 3.542,0.156 3.854,0.354 0.313,0.198 10 false d2

a.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
d2-13 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation