Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM38G0E _58 Vehicle Interior _100628 SEAT _0467514 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK POSITION CONTROL ECU ASSEMBLY (for LHD)


E360013N41
5.021,0.333 5.438,0.583 0.417,0.25 2.552,0.333 2.969,0.583 0.417,0.25 1.5,0.333 1.917,0.583 0.417,0.25 5.104,0.365 5.417,0.563 0.313,0.198 10 false i19 2.635,0.365 2.948,0.563 0.313,0.198 10 false i18 1.583,0.365 1.896,0.563 0.313,0.198 10 false i17

a.

Disconnect the i17 and i19 position control ECU assembly connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Terminal Description Condition Specified Condition
i17-3 (+B) - Body ground Battery power supply Always 11 to 14 V
i19-1 (IG) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
i19-15 (SYSB) - Body ground System power source Always 11 to 14 V
i17-2 (GND) - Body ground Ground Always Below 1 Ω
i19-27 (DBCL) - Body ground Driver seat belt buckle switch signal Driver seat belt unfastened 10 kΩ or higher
Driver seat belt fastened Below 1 Ω


c.

Reconnect the i17 and i19 position control ECU assembly connectors.


d.

Measure the voltage and resistance according to the value (s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
i17-1 (SLD+) - Body ground Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
i17-5 (SLD-) - Body ground Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
i17-6 (LFT+) - Body ground Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
i18-5 (LFT-) - Body ground Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V
i17-10 (RCL+) - Body ground Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
i18-6 (RCL-) - Body ground Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
i17-7 (FRV+) - Body ground Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
i18-4 (FRV-) - Body ground Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
i17-9 (L+) - Body ground Lumbar support adjuster motor signal (forward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Forward) 11 to 14 V
i18-3 (L-) - Body ground Lumbar support adjuster motor signal (rearward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Rearward) 11 to 14 V
i19-4 (LFLF) - Body ground Front power seat switch LH (lumbar support adjuster switch (forward)) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Forward) Below 1 V
i19-18 (LFLR) - Body ground Front power seat switch LH (lumbar support adjuster switch (rearward)) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Rearward) Below 1 V
i19-9 (SLDF) - Body ground Front power seat switch LH (slide switch (forward)) signal Slide switch off 11 to 14 V
Slide switch on (Forward) Below 1 V
i19-23 (SLDR) - Body ground Front power seat switch LH (slide switch (rearward)) signal Slide switch off 11 to 14 V
Slide switch on (Rearward) Below 1 V
i19-8 (RCLF) - Body ground Front power seat switch LH (reclining switch (forward)) signal Reclining switch off 11 to 14 V
Reclining switch on (Forward) Below 1 V
i19-22 (RCLR) - Body ground Front power seat switch LH (reclining switch (rearward)) signal Reclining switch off 11 to 14 V
Reclining switch on (Rearward) Below 1 V
i19-6 (FRVU) - Body ground Front power seat switch LH (front vertical switch (upward)) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Upward) Below 1 V
i19-20 (FRVD) - Body ground Front power seat switch LH (front vertical switch (downward)) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Downward) Below 1 V
i19-7 (LFTU) - Body ground Front power seat switch LH (lifter switch (upward)) signal Lifter switch off 11 to 14 V
Lifter switch on (Upward) Below 1 V
i19-21 (LFTD) - Body ground Front power seat switch LH (lifter switch (downward)) signal Lifter switch off 11 to 14 V
Lifter switch on (Downward) Below 1 V
i19-12 (SGND) - Body ground Sensor ground Always Below 1 Ω


e.

Check for pulses according to the value (s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
i19-10 (SSFV) - Body ground Front vertical position signal Front vertical function operating Pulse generation
i19-11 (SSRR) - Body ground Reclining position signal Reclining function operating Pulse generation
i19-25 (SSRL) - Body ground Lifter position signal Lifter function operating Pulse generation
i19-26 (SSRS) - Body ground Slide position signal Slide function operating Pulse generation



CHECK POSITION CONTROL ECU ASSEMBLY (for RHD)


E360013N42
5.021,0.333 5.438,0.583 0.417,0.25 2.552,0.333 2.969,0.583 0.417,0.25 1.5,0.333 1.917,0.583 0.417,0.25 5.104,0.365 5.417,0.563 0.313,0.198 10 false h24 2.635,0.365 2.948,0.563 0.313,0.198 10 false h23 1.583,0.365 1.896,0.563 0.313,0.198 10 false h22

a.

Disconnect the h22 and h24 position control ECU assembly connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Tester Connection Terminal Description Condition Specified Condition
h22-3 (+B) - Body ground Battery power supply Always 11 to 14 V
h24-1 (IG) - Body ground Ignition power supply Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
h24-15 (SYSB) - Body ground System power source Always 11 to 14 V
h22-2 (GND) - Body ground Ground Always Below 1 Ω
h24-27 (DBCL) - Body ground Driver seat belt buckle switch signal Driver seat belt unfastened 10 kΩ or higher
Driver seat belt fastened Below 1 Ω


c.

Reconnect the h22 and h24 position control ECU assembly connectors.


d.

Measure the voltage and resistance according to the value (s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
h22-1 (SLD+) - Body ground Slide motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
h22-5 (SLD-) - Body ground Slide motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
h22-6 (LFT+) - Body ground Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
h23-5 (LFT-) - Body ground Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V
h22-10 (RCL+) - Body ground Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
h23-6 (RCL-) - Body ground Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
h22-7 (FRV+) - Body ground Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
h23-4 (FRV-) - Body ground Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
h22-9 (L+) - Body ground Lumbar support adjuster motor signal (forward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Forward) 11 to 14 V
h23-3 (L-) - Body ground Lumbar support adjuster motor signal (rearward) Lumbar support adjuster switch off Below 1 V
Lumbar support adjuster switch on (Rearward) 11 to 14 V
h24-4 (LFLF) - Body ground Front power seat switch RH (lumbar support adjuster switch (forward)) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Forward) Below 1 V
h24-18 (LFLR) - Body ground Front power seat switch RH (lumbar support adjuster switch (rearward)) signal Lumbar support adjuster switch off 11 to 14 V
Lumbar support adjuster switch on (Rearward) Below 1 V
h24-9 (SLDF) - Body ground Front power seat switch RH (slide switch (forward)) signal Slide switch off 11 to 14 V
Slide switch on (Forward) Below 1 V
h24-23 (SLDR) - Body ground Front power seat switch RH (slide switch (rearward)) signal Slide switch off 11 to 14 V
Slide switch on (Rearward) Below 1 V
h24-8 (RCLF) - Body ground Front power seat switch RH (reclining switch (forward)) signal Reclining switch off 11 to 14 V
Reclining switch on (Forward) Below 1 V
h24-22 (RCLR) - Body ground Front power seat switch RH (reclining switch (rearward)) signal Reclining switch off 11 to 14 V
Reclining switch on (Rearward) Below 1 V
h24-6 (FRVU) - Body ground Front power seat switch RH (front vertical switch (upward)) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Upward) Below 1 V
h24-20 (FRVD) - Body ground Front power seat switch RH (front vertical switch (downward)) signal Front vertical switch off 11 to 14 V
Front vertical switch on (Downward) Below 1 V
h24-7 (LFTU) - Body ground Front power seat switch RH (lifter switch (upward)) signal Lifter switch off 11 to 14 V
Lifter switch on (Upward) Below 1 V
h24-21 (LFTD) - Body ground Front power seat switch RH (lifter switch (downward)) signal Lifter switch off 11 to 14 V
Lifter switch on (Downward) Below 1 V
h24-12 (SGND) - Body ground Sensor ground Always Below 1 Ω


e.

Check for pulses according to the value (s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
h24-10 (SSFV) - Body ground Front vertical position signal Front vertical function operating Pulse generation
h24-11 (SSRR) - Body ground Reclining position signal Reclining function operating Pulse generation
h24-25 (SSRL) - Body ground Lifter position signal Lifter function operating Pulse generation
h24-26 (SSRS) - Body ground Slide position signal Slide function operating Pulse generation



CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND POWER DISTRIBUTION BOX ASSEMBLY


E448686C15
3.458,7.583 3.854,7.885 0.396,0.302 5.594,3.219 6.01,3.458 0.417,0.24 1.146,3.198 1.563,3.438 0.417,0.24 1.219,4.469 1.635,4.708 0.417,0.24 1.458,6.042 1.875,6.281 0.417,0.24 3.615,6.063 4.031,6.302 0.417,0.24 4.385,4.458 4.802,4.698 0.417,0.24 6.375,6.073 6.792,6.313 0.417,0.24 4.719,6.094 5.135,6.333 0.417,0.24 6.208,4.479 6.625,4.719 0.417,0.24 5.49,6.094 5.906,6.333 0.417,0.24 3.469,3.188 3.885,3.427 0.417,0.24 2.219,0.917 2.219,0.698 2.219,0.698 2.385,0.698 true 0.646,1.229 0.927,1.229 true 2.229,1.51 2.469,1.51 true 2.219,1.802 2.458,1.802 true 0.646,2.073 0.885,2.073 true 0.635,2.302 0.875,2.302 true 0.646,2.542 1.125,2.542 true 0.635,1.698 0.917,1.698 true 6.292,1.156 6.573,1.156 true 6.271,1.75 6.552,1.75 true 6.292,2.208 6.573,2.208 true 2.229,2.125 2.469,2.125 true 1.177,0.542 1.177,0.323 1.177,0.323 1.344,0.323 true 4.865,0.563 4.865,0.344 4.865,0.344 5.031,0.344 true 6.146,0.51 6.146,0.292 6.146,0.292 6.313,0.292 true 4.25,0.969 4.719,1.542 0.469,0.573 10 false MB 3.563,7.656 4.063,8.281 0.5,0.625 10 false MB 0.469,1.635 0.781,1.833 0.313,0.198 10 false 5E 0.479,2.031 0.792,2.229 0.313,0.198 10 false 5K 2.521,1.448 2.979,1.646 0.458,0.198 10 false I1 2.51,1.74 2.969,1.938 0.458,0.198 10 false I2 0.448,2.24 0.948,2.469 0.5,0.229 10 false 5J 2.458,0.635 2.917,0.833 0.458,0.198 10 false *2 6.656,1.083 6.969,1.281 0.313,0.198 10 false 5C 6.615,1.677 6.927,1.875 0.313,0.198 10 false 5B 5.75,3.26 6.208,3.458 0.458,0.198 10 false I1 3.615,3.229 4.073,3.427 0.458,0.198 10 false I2 1.344,4.521 1.656,4.719 0.313,0.198 10 false 5C 4.531,4.521 4.844,4.719 0.313,0.198 10 false 5B 1.583,6.094 1.896,6.292 0.313,0.198 10 false 5F 3.74,6.125 4.052,6.323 0.313,0.198 10 false 5E 6.479,6.125 6.792,6.323 0.313,0.198 10 false 5H 4.865,6.146 5.219,6.302 0.354,0.156 10 false 5K 0.448,1.146 1.063,1.344 0.615,0.198 10 false 5F 0.469,2.49 0.969,2.719 0.5,0.229 10 false 5H 6.615,2.135 6.927,2.333 0.313,0.198 10 false 5A 6.344,4.542 6.656,4.74 0.313,0.198 10 false 5A 5.635,6.146 5.948,6.344 0.313,0.198 10 false 5J 2.521,2.063 2.979,2.26 0.458,0.198 10 false I3 1.323,3.25 1.781,3.448 0.458,0.198 10 false I3 1.406,0.24 1.865,0.438 0.458,0.198 10 false *1 5.104,0.25 5.563,0.448 0.458,0.198 10 false *1 6.375,0.188 6.833,0.385 0.458,0.198 10 false *1
*1 Power Distribution Box Assembly *2 Main Body ECU (Multiplex Network Body ECU)


a.

Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL


b.

Reconnect the power distribution box assembly connectors.


c.

Measure the voltage and resistance according to the value (s) in the table below.

Tester Connection Terminal Description Condition Specified Condition
MB-26 (BECU) - Body ground Battery power supply Always 11 to 14 V
MB-27 (IGR) - Body ground Ignition power supply Ignition switch ON 11 to 14 V
MB-27 (IGR) - Body ground Ignition power supply Ignition switch off Below 1 V
MB-13 (GND1) - Body ground Ground Always Below 1 Ω


d.

Install the main body ECU (multiplex network body ECU) to power distribution box assembly.

for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>INSTALLATION

for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>INSTALLATION


e.

Measure the voltage for pulses according to the value(s) in the table below.

Tester Connection Terminal Description Condition Specified Condition

*1: for RHD

*2: for LHD

MB-4 (FRCY) - Body ground*1 Front door courtesy light switch assembly (for RH) signal Front door RH open Below 1 V
Front door RH closed 4.7 to 5.3 V
MB-2 (FLCY) - Body ground*2 Front door courtesy light switch assembly (for LH) signal Front door LH open Below 1 V
Front door LH closed 4.7 to 5.3 V