Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM38G0E _58 Vehicle Interior _100628 SEAT _0467514 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Position is not Memorized  


DESCRIPTION

The position control ECU assembly receives seat memory switch signals from the main body ECU (multiplex network body ECU) via CAN communication. If the SET switch is being pressed when one of the M1, M2 or M3 switches is pressed, or if one of the M1, M2 or M3 switches is pressed within 3 seconds of pressing the SET switch, the main body ECU (multiplex network body ECU) sends a memory request signal to the position control ECU assembly. After receiving the request signal, the position control ECU assembly memorizes the location data of each motor.

WIRING DIAGRAM

for LHD:


B613105E01
0.344,1.052 1.667,1.51 1.323,0.458 10 false Position Control ECU Assembly 3.156,3.156 4.813,3.594 1.656,0.438 10 false Outer Mirror Control ECU Assembly LH 5.469,3.333 7.052,3.667 1.583,0.333 10 false Seat Memory Switch LH 4.396,0.458 5.042,0.74 0.646,0.281 10 false M1 4.385,1.146 5.031,1.427 0.646,0.281 10 false M2 4.385,1.792 5.031,2.073 0.646,0.281 10 false M3 5.542,1.688 6.188,1.969 0.646,0.281 10 false M3 5.542,0.344 6.188,0.625 0.646,0.281 10 false M1 5.542,1.031 6.188,1.313 0.646,0.281 10 false M2 4.688,0.354 5.333,0.635 0.646,0.281 10 false 2 4.688,1.031 5.333,1.313 0.646,0.281 10 false 3 4.698,1.688 5.344,1.969 0.646,0.281 10 false 4 5.344,0.344 5.99,0.625 0.646,0.281 10 false 1 5.344,1.021 5.99,1.302 0.646,0.281 10 false 2 5.354,1.677 6,1.958 0.646,0.281 10 false 3 3.156,2.958 3.802,3.24 0.646,0.281 10 false N1 5.479,3.146 6.458,3.427 0.979,0.281 10 false N20 0.719,3.458 2.688,3.677 1.969,0.219 10 false : CAN Communication Line 5.542,2.615 6.188,2.896 0.646,0.281 10 false E 5.354,2.615 6,2.896 0.646,0.281 10 false 5 5.531,2.281 6.177,2.563 0.646,0.281 10 false MRY 5.354,2.281 6,2.563 0.646,0.281 10 false 4 4.688,2.292 5.333,2.573 0.646,0.281 10 false 1 4.344,2.375 4.99,2.656 0.646,0.281 10 false MM 0.167,2.74 1.99,3.125 1.823,0.385 10 false Main Body ECU (Multiplex Network Body ECU)


for RHD:


B613105E02
0.271,1.031 1.604,1.542 1.333,0.51 10 false Position Control ECU Assembly 3.156,3.135 4.75,3.594 1.594,0.458 10 false Outer Mirror Control ECU Assembly RH 5.469,3.333 7.063,3.635 1.594,0.302 10 false Seat Memory Switch RH 4.396,0.458 5.042,0.74 0.646,0.281 10 false M1 4.385,1.146 5.031,1.427 0.646,0.281 10 false M2 4.385,1.792 5.031,2.073 0.646,0.281 10 false M3 5.542,1.688 6.188,1.969 0.646,0.281 10 false M3 5.542,0.344 6.188,0.625 0.646,0.281 10 false M1 5.542,1.031 6.188,1.313 0.646,0.281 10 false M2 4.688,0.354 5.333,0.635 0.646,0.281 10 false 2 4.688,1.031 5.333,1.313 0.646,0.281 10 false 3 4.698,1.688 5.344,1.969 0.646,0.281 10 false 4 5.344,0.344 5.99,0.625 0.646,0.281 10 false 5 5.344,1.021 5.99,1.302 0.646,0.281 10 false 4 5.354,1.677 6,1.958 0.646,0.281 10 false 3 3.156,2.958 3.802,3.24 0.646,0.281 10 false M1 5.479,3.146 6.458,3.427 0.979,0.281 10 false M8 0.719,3.458 2.688,3.677 1.969,0.219 10 false : CAN Communication Line 5.542,2.615 6.188,2.896 0.646,0.281 10 false E 5.354,2.615 6,2.896 0.646,0.281 10 false 1 5.531,2.281 6.177,2.563 0.646,0.281 10 false MRY 5.354,2.281 6,2.563 0.646,0.281 10 false 2 4.688,2.292 5.333,2.573 0.646,0.281 10 false 1 4.344,2.375 4.99,2.656 0.646,0.281 10 false MM 0.177,2.719 1.896,3.188 1.719,0.469 10 false Main Body ECU (Multiplex Network Body ECU)


CAUTION / NOTICE / HINT

NOTICE:
·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1, M2 or M3 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1, M2 or M3 switch) are pressed simultaneously.

If a restoring operation has failed, release all of the switches. The seat memory restoring function will not operate unless the switches are released.

·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FRONT POWER SEAT CONTROL OPERATION

B

10.CHECK FRONT POWER SEAT CONTROL OPERATION
2.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch LH.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the front power seat switch LH.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (DRIVER SEAT MEMORY SWITCH)

NG

3.READ VALUE USING GTS (DRIVER SEAT MEMORY SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Mirror L > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 switch signal OFF or ON OFF: Seat memory switch M1 switch off
ON: Seat memory switch M1 switch on
-
Seat Memory Switch2 Seat memory switch M2 switch signal OFF or ON OFF: Seat memory switch M2 switch off
ON: Seat memory switch M2 switch on
-
Seat Memory Switch3 Seat memory switch M3 switch signal OFF or ON OFF: Seat memory switch M3 switch off
ON: Seat memory switch M3 switch on
-
Seat Memory Set SW Seat memory switch SET switch signal OFF or ON OFF: Seat memory switch SET switch off
ON: Seat memory switch SET switch on
-
Body Electrical > Mirror L > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Switch3
Seat Memory Set SW
50003 225 1,2,3,4
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

4.PERFORM ACTIVE TEST USING GTS (BUZZER)

NG

7.INSPECT SEAT MEMORY SWITCH LH
4.PERFORM ACTIVE TEST USING GTS (BUZZER)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Buzzer operation OFF/ON -
Body Electrical > Driver Seat > Active Test
Tester Display
Buzzer
50004 162 5
OK:

Buzzer sounds normally.



Result:
Proceed to
OK
NG



OK

5.REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPLACE POSITION CONTROL ECU ASSEMBLY

5.REPLACE POSITION CONTROL ECU ASSEMBLY
a.

Replace the position control ECU assembly with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU (for Front Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
6.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

7.INSPECT SEAT MEMORY SWITCH LH

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - SEAT MEMORY SWITCH LH)

NG

REPLACE SEAT MEMORY SWITCH LH

8.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - SEAT MEMORY SWITCH LH)
a.

Disconnect the N1 outer mirror control ECU assembly LH connector.


b.

Disconnect the N20 seat memory switch LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N1,N20)Location & Routing

Click Connector(N1)Body>Front Door Wire LH>Outer Mirror Control ECU Assembly LH

Click Connector(N20)Body>Front Door Wire LH>Seat Memory Switch LH

N1-2 (M1) - N20-1 (M1) Always Below 1 Ω
N1-2 (M1) or N20-1 (M1) - Body ground Always 10 kΩ or higher
N1-3 (M2) - N20-2 (M2) Always Below 1 Ω
N1-3 (M2) or N20-2 (M2) - Body ground Always 10 kΩ or higher
N1-4 (M3) - N20-3 (M3) Always Below 1 Ω
N1-4 (M3) or N20-3 (M3) - Body ground Always 10 kΩ or higher
N1-1 (MM) - N20-4 (MRY) Always Below 1 Ω
N1-1 (MM) or N20-4 (MRY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH LH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH LH - BODY GROUND)
a.

Disconnect the N20 seat memory switch LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(N20)Location & Routing

Click Connector(N20)Body>Front Door Wire LH>Seat Memory Switch LH

N20-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch RH.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the front power seat switch RH.



Result:
Proceed to
OK
NG



OK

11.READ VALUE USING GTS (DRIVER SEAT MEMORY SWITCH)

NG

11.READ VALUE USING GTS (DRIVER SEAT MEMORY SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Mirror R > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Seat Memory Switch1 Seat memory switch M1 switch signal OFF or ON OFF: Seat memory switch M1 switch off
ON: Seat memory switch M1 switch on
-
Seat Memory Switch2 Seat memory switch M2 switch signal OFF or ON OFF: Seat memory switch M2 switch off
ON: Seat memory switch M2 switch on
-
Seat Memory Switch3 Seat memory switch M3 switch signal OFF or ON OFF: Seat memory switch M3 switch off
ON: Seat memory switch M3 switch on
-
Seat Memory Set SW Seat memory switch SET switch signal OFF or ON OFF: Seat memory switch SET switch off
ON: Seat memory switch SET switch on
-
Body Electrical > Mirror R > Data List
Tester Display
Seat Memory Switch1
Seat Memory Switch2
Seat Memory Switch3
Seat Memory Set SW
50003 224 1,2,3,4
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

12.PERFORM ACTIVE TEST USING GTS (BUZZER)

NG

15.INSPECT SEAT MEMORY SWITCH RH
12.PERFORM ACTIVE TEST USING GTS (BUZZER)
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Buzzer Buzzer operation OFF/ON -
Body Electrical > Driver Seat > Active Test
Tester Display
Buzzer
50004 162 5
OK:

Buzzer sounds normally.



Result:
Proceed to
OK
NG



OK

13.REPLACE POSITION CONTROL ECU ASSEMBLY

NG

REPLACE POSITION CONTROL ECU ASSEMBLY

13.REPLACE POSITION CONTROL ECU ASSEMBLY
a.

Replace the position control ECU assembly with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU (for Front Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
14.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

15.INSPECT SEAT MEMORY SWITCH RH

Click hereVehicle Interior>SEAT>SEAT MEMORY SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - SEAT MEMORY SWITCH RH)

NG

REPLACE SEAT MEMORY SWITCH RH

16.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - SEAT MEMORY SWITCH RH)
a.

Disconnect the M1 outer mirror control ECU assembly RH connector.


b.

Disconnect the M8 seat memory switch RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M1,M8)Location & Routing

Click Connector(M1)Body>Front Door Wire RH>Outer Mirror Control ECU Assembly RH

Click Connector(M8)Body>Front Door Wire RH>Seat Memory Switch RH

M1-2 (M1) - M8-5 (M1) Always Below 1 Ω
M1-2 (M1) or M8-5 (M1) - Body ground Always 10 kΩ or higher
M1-3 (M2) - M8-4 (M2) Always Below 1 Ω
M1-3 (M2) or M8-4 (M2) - Body ground Always 10 kΩ or higher
M1-4 (M3) - M8-3 (M3) Always Below 1 Ω
M1-4 (M3) or M8-3 (M3) - Body ground Always 10 kΩ or higher
M1-1 (MM) - M8-2 (MRY) Always Below 1 Ω
M1-1 (MM) or M8-2 (MRY) - Body ground Always 10 kΩ or higher
M8-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH RH - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH RH - BODY GROUND)
a.

Disconnect the M8 seat memory switch RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition

Click Location & Routing(M8)Location & Routing

Click Connector(M8)Body>Front Door Wire RH>Seat Memory Switch RH

M8-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR