Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › 2021.04–2021.07
RM38G0E _58 Vehicle Interior _100628 SEAT _0467514 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat does not Return to Memorized Position  


DESCRIPTION

When the M1, M2 or M3 switch of the seat memory switch is pressed, the main body ECU (multiplex network body ECU) sends a switch signal to the position control ECU assembly via CAN communication. Then, the main body ECU (multiplex network body ECU) sends a recall request signal to the position control ECU assembly. The position control ECU assembly operates each motor to move the seat to the memorized position.

WIRING DIAGRAM

for LHD:


B613105E01
0.344,1.052 1.667,1.51 1.323,0.458 10 false Position Control ECU Assembly 3.156,3.156 4.813,3.594 1.656,0.438 10 false Outer Mirror Control ECU Assembly LH 5.469,3.333 7.052,3.667 1.583,0.333 10 false Seat Memory Switch LH 4.396,0.458 5.042,0.74 0.646,0.281 10 false M1 4.385,1.146 5.031,1.427 0.646,0.281 10 false M2 4.385,1.792 5.031,2.073 0.646,0.281 10 false M3 5.542,1.688 6.188,1.969 0.646,0.281 10 false M3 5.542,0.344 6.188,0.625 0.646,0.281 10 false M1 5.542,1.031 6.188,1.313 0.646,0.281 10 false M2 4.688,0.354 5.333,0.635 0.646,0.281 10 false 2 4.688,1.031 5.333,1.313 0.646,0.281 10 false 3 4.698,1.688 5.344,1.969 0.646,0.281 10 false 4 5.344,0.344 5.99,0.625 0.646,0.281 10 false 1 5.344,1.021 5.99,1.302 0.646,0.281 10 false 2 5.354,1.677 6,1.958 0.646,0.281 10 false 3 3.156,2.958 3.802,3.24 0.646,0.281 10 false N1 5.479,3.146 6.458,3.427 0.979,0.281 10 false N20 0.719,3.458 2.688,3.677 1.969,0.219 10 false : CAN Communication Line 5.542,2.615 6.188,2.896 0.646,0.281 10 false E 5.354,2.615 6,2.896 0.646,0.281 10 false 5 5.531,2.281 6.177,2.563 0.646,0.281 10 false MRY 5.354,2.281 6,2.563 0.646,0.281 10 false 4 4.688,2.292 5.333,2.573 0.646,0.281 10 false 1 4.344,2.375 4.99,2.656 0.646,0.281 10 false MM 0.167,2.74 1.99,3.125 1.823,0.385 10 false Main Body ECU (Multiplex Network Body ECU)


for RHD:


B613105E02
0.271,1.031 1.604,1.542 1.333,0.51 10 false Position Control ECU Assembly 3.156,3.135 4.75,3.594 1.594,0.458 10 false Outer Mirror Control ECU Assembly RH 5.469,3.333 7.063,3.635 1.594,0.302 10 false Seat Memory Switch RH 4.396,0.458 5.042,0.74 0.646,0.281 10 false M1 4.385,1.146 5.031,1.427 0.646,0.281 10 false M2 4.385,1.792 5.031,2.073 0.646,0.281 10 false M3 5.542,1.688 6.188,1.969 0.646,0.281 10 false M3 5.542,0.344 6.188,0.625 0.646,0.281 10 false M1 5.542,1.031 6.188,1.313 0.646,0.281 10 false M2 4.688,0.354 5.333,0.635 0.646,0.281 10 false 2 4.688,1.031 5.333,1.313 0.646,0.281 10 false 3 4.698,1.688 5.344,1.969 0.646,0.281 10 false 4 5.344,0.344 5.99,0.625 0.646,0.281 10 false 5 5.344,1.021 5.99,1.302 0.646,0.281 10 false 4 5.354,1.677 6,1.958 0.646,0.281 10 false 3 3.156,2.958 3.802,3.24 0.646,0.281 10 false M1 5.479,3.146 6.458,3.427 0.979,0.281 10 false M8 0.719,3.458 2.688,3.677 1.969,0.219 10 false : CAN Communication Line 5.542,2.615 6.188,2.896 0.646,0.281 10 false E 5.354,2.615 6,2.896 0.646,0.281 10 false 1 5.531,2.281 6.177,2.563 0.646,0.281 10 false MRY 5.354,2.281 6,2.563 0.646,0.281 10 false 2 4.688,2.292 5.333,2.573 0.646,0.281 10 false 1 4.344,2.375 4.99,2.656 0.646,0.281 10 false MM 0.177,2.719 1.896,3.188 1.719,0.469 10 false Main Body ECU (Multiplex Network Body ECU)


CAUTION / NOTICE / HINT

NOTICE:
·

The interference prevention function stops the recall operation when the head restraint may contact the roof headlining during a recall operation.

·

The seat position will not be stored if the SET switch and 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a memorizing operation has failed, release all of the switches. The seat memory function will not operate unless the switches are released.

·

The seat will not return to the memorized position if 2 or more of the seat memory switches (for example, M1 switch and M2 switch) are pressed simultaneously.

If a restoring operation has failed, release all of the switches. The seat memory restoring function will not operate unless the switches are released.

·

The front power seat control system (w/ Memory) uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for LHD A
for RHD B



A

2.CHECK FRONT POWER SEAT CONTROL OPERATION

B

10.CHECK FRONT POWER SEAT CONTROL OPERATION
2.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch LH.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the front power seat switch LH.



Result:
Proceed to
OK
NG



OK

3.CHECK SEAT POSITION MEMORY FUNCTION

NG

3.CHECK SEAT POSITION MEMORY FUNCTION
a.

Check the seat position memory function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory function is normal.



Result:
Proceed to
OK
NG



OK

4.CHECK SEAT POSITION RESTORING FUNCTION

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

4.CHECK SEAT POSITION RESTORING FUNCTION
a.

Under each of the following conditions, check that the seat position restoring function operates by pressing the M1, M2 or M3 switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

·

The ignition switch is ON, and the shift lever is in P.*1

·

Within 180 seconds after the driver door is opened with the ignition switch off.*2

·

Within 60 seconds after the driver door is opened and then closed with the ignition switch off.*3



Result:
Result Proceed to
Seat position restoring function does not operate at all. A
Seat position restoring function does not operate when the condition is *1. B
·

Seat position restoring function does not operate when the condition is *2.

·

Seat position restoring function does not operate when the condition is *3.


C



A

5.READ VALUE USING GTS (SEAT POSITION MEMORY)

B

8.READ VALUE USING GTS (SHIFT P POSITION)

C

9.READ VALUE USING GTS (FL DOOR COURTESY SWITCH STATUS)
5.READ VALUE USING GTS (SEAT POSITION MEMORY)
a.

Store a seat position in memory for the M1, M2 and M3 switches.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK


b.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Memory No3 Seat position memorized with M3 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Memory No1
Memory No2
Memory No3
50003 162 700,701,702
OK:

Mem is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

6.REPLACE POSITION CONTROL ECU ASSEMBLY

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

6.REPLACE POSITION CONTROL ECU ASSEMBLY
a.

Replace the position control ECU assembly with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU (for Front Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
7.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

8.READ VALUE USING GTS (SHIFT P POSITION)
a.

Read the Data List according to the display on the GTS.

i.

for 1GR-FE:

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (N,P Range) Park/Neutral position switch ON or OFF ON: Shift lever in N or P
OFF: Shift lever not in N or P
-
Powertrain > Engine > Data List
Tester Display
Shift SW Status (N,P Range)
50003 372 263

ii.

for V35A-FTS:

Powertrain > Transmission
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (N,P Range) Park/Neutral position switch ON or OFF ON: Shift lever in N or P
OFF: Shift lever not in N or P
-
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (N,P Range)
50003 373 263


OK:

On the GTS screen, ON or OFF is displayed accordingly.


Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

9.READ VALUE USING GTS (FL DOOR COURTESY SWITCH STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Door Courtesy Switch Status Front door courtesy light switch assembly (LH) signal Close or Open Close: Front door LH closed
Open: Front door LH open
-
Body Electrical > Main Body > Data List
Tester Display
FL Door Courtesy Switch Status
50003 449 31
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)

10.CHECK FRONT POWER SEAT CONTROL OPERATION
a.

Check that each function of the power seat operates normally by using the front power seat switch RH.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Each function of the power seat operates normally using the front power seat switch RH.



Result:
Proceed to
OK
NG



OK

11.CHECK SEAT POSITION MEMORY FUNCTION

NG

11.CHECK SEAT POSITION MEMORY FUNCTION
a.

Check the seat position memory function.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory function is normal.



Result:
Proceed to
OK
NG



OK

12.CHECK SEAT POSITION RESTORING FUNCTION

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

12.CHECK SEAT POSITION RESTORING FUNCTION
a.

Under each of the following conditions, check that the seat position restoring function operates by pressing the M1, M2 or M3 switch.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

·

The ignition switch is ON, and the shift lever is in P.*1

·

Within 180 seconds after the driver door is opened with the ignition switch off.*2

·

Within 60 seconds after the driver door is opened and then closed with the ignition switch off.*3



Result:
Result Proceed to
Seat position restoring function does not operate at all. A
Seat position restoring function does not operate when the condition is *1. B
·

Seat position restoring function does not operate when the condition is *2.

·

Seat position restoring function does not operate when the condition is *3.


C



A

13.READ VALUE USING GTS (SEAT POSITION MEMORY)

B

16.READ VALUE USING GTS (SHIFT P POSITION)

C

17.READ VALUE USING GTS (FR DOOR COURTESY SWITCH STATUS)
13.READ VALUE USING GTS (SEAT POSITION MEMORY)
a.

Store a seat position in memory for the M1, M2 and M3 switches.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK


b.

Read the Data List according to the display on the GTS.

Body Electrical > Driver Seat > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Memory No1 Seat position memorized with M1 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Memory No2 Seat position memorized with M2 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Memory No3 Seat position memorized with M3 switch Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Body Electrical > Driver Seat > Data List
Tester Display
Memory No1
Memory No2
Memory No3
50003 162 700,701,702
OK:

Mem is displayed on the GTS screen.



Result:
Proceed to
OK
NG



OK

14.REPLACE POSITION CONTROL ECU ASSEMBLY

NG

GO TO OTHER DIAGNOSIS PROCEDURE (Power Seat Position is not Memorized)

14.REPLACE POSITION CONTROL ECU ASSEMBLY
a.

Replace the position control ECU assembly with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT CONTROL ECU (for Front Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
15.CHECK SEAT POSITION MEMORY AND RESTORING FUNCTION
a.

Check the seat position memory and restoring functions.

Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK

OK:

Seat position memory and restoring functions operate normally.



Result:
Proceed to
OK
NG



OK

END (POSITION CONTROL ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

16.READ VALUE USING GTS (SHIFT P POSITION)
a.

Read the Data List according to the display on the GTS.

i.

for 1GR-FE:

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (N,P Range) Park/Neutral position switch ON or OFF ON: Shift lever in N or P
OFF: Shift lever not in N or P
-
Powertrain > Engine > Data List
Tester Display
Shift SW Status (N,P Range)
50003 372 263

ii.

for V35A-FTS:

Powertrain > Transmission
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (N,P Range) Park/Neutral position switch ON or OFF ON: Shift lever in N or P
OFF: Shift lever not in N or P
-
Powertrain > Transmission > Data List
Tester Display
Shift SW Status (N,P Range)
50003 373 263


OK:

On the GTS screen, ON or OFF is displayed accordingly.


Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

17.READ VALUE USING GTS (FR DOOR COURTESY SWITCH STATUS)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy Switch Status Front door courtesy light switch assembly (RH) signal Close or Open Open: Front door RH open
Close: Front door RH closed
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy Switch Status
50003 449 30
OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY

NG

GO TO LIGHTING SYSTEM (Door Courtesy Switch Circuit)